MATERIAL SAFETY DATA SHEET Aerocel / Aeroseal
Contact Adhesive
_________________________________ __________________________________
I. PRODUCT IDENTIFICATION__________________________________
Prepared 12/04
Name: AEROFLEX AEROSEAL CONTACT ADHESIVE
Description: Solvent-dispersed synthetic rubber resin adhesive
___________________________________________________________
II. DEPARTMENT OF TRANSPORTATION INFORMATION___________ Aeroflex USA, Inc.
Shipping Name: Adhesive containing a flammable liquid (Hexane & Acetone) 9051 Executive Park Drive
Hazard Class: 3 (Flammable Liquid) ID #: UN 1133 PG: II (AEROCEL
Suite 400
Contact Adhesive)
Reportable Quantity (RQ): 6250 lb. Knoxville, TN 37923
EMERGENCY ONLY CONTACT: CHEM-TEL 1-800-255-3924___________
Tel 865-690-5740
III HMIS (0=minimal hazard; 4=severe hazard____________________________
Health = 2 Flammability = 3 Reactivity = 0
Fax 865-690-5695
___________________________________________________________________
IV.PRODUCT CONTENT________________________________________
This product contains chemicals subject to the reporting requirements of Manufactured in Sweetwater, TN
Section 313 of Title III of the Superfund Amendment and Reauthorization Act USA
Of 1986 and 40 CFR Part 372. All components are on TSCA inventory. This
Product does NOT contain asbestos or polychlorinated biphenyls.
______________________________________________________________________________________________________________
V. HAZARDOUS INGREDIENTS__________________________________________________________________________________________________
INGREDIENT: C.A.S. NO. PERCENT Phosphate
Acetone 67-64-1 disocyanate Chemical Name: Tri phosphate
Toluene 108-88-3 Formal Name: Methylene Diphonyl Formal Name: Tri phosphate
Hexane 110-54-3 Diisocyanate Chemical Family: Alkyl Phosphate
Synthetic Rubber N/A Chemical Formula: OCN-R-NCO Chemical Formula: O-P-(OC3H3CI)3
Phenolic Resin 25085-50-1 CAS No.: 9016-87-9 CAS No. 13674-84-5
Rubber Curing Ingredients 1309-48-4
______________________________________________________________________________________________________________
____________________________________________________
________________________________________________________________
V. FIRE AND EXPLOSION HAZARDS___________________________
X. PHYSICAL AND CHEMICAL PROPERTIES______________________
Rigid polyurethane is similar to other organic materials such as wood,
Appearance: Expanded rubber foam. Specific gravity (H2O=1): 0.04-
wool or rubber, and can present unreasonable fire risks in certain
0.09; Service Temperature: -57 50 +105 C (-70 tp +220 F); Thermal
misapplications when exposed to ignition sources in air. Once ignited,
Conductivity (W/mK): 0.040 at mean temp 40 C; Water vapor
such fire can produce heat, smoke and irritating or toxic gases. Carbon
permeability: 0.10 perm-inch (0.15X10-12Kg/Pa s m): Water Absorption
dioxide, carbon monoxide, possible traces of hydrogen cyanide, halogen
(% by weight): 5% by weight; Compression set: Excellent; Flammability:
acids, and nitrogen oxides can be evolved under fire condition. Install
Self-extinguishing
conditions: Install Aerofix only after all welding, cutting or other hot work
________________________________________________________________
has been completed. If hot work must be done after Aerofix has been
XI. FIRE-FIGHTING MEASURES___________________________________
installed, the hot work trade personnel must be warned. Remove
Extinguishing Media: Use water spray, foam, carbon dioxide or dry
combustible material from the vicinity immediately below the work area.
chemical extinguishers. Use self contained breathing apparatus for
Post a fire guard equipped with a fire extinguisher during and for 30
smoke protection and usual body protection.
minutes after hot operations. Stop work immediately if foam begins to
________________________________________________________________
smoke and remove material from the work area. Work should be carried
XII. HANDLING AND STORAGE_______________________________
out in a well ventilated area. Do not breathe fumes.
________________________________________________________________ Storage: Potential risks associated with rigid polyurethane arise from
dust, fire and toxic thermal decomposition products and may result from
VI. DISPOSAL CONSIDERATION______________________________
improper storage. Keep in cool dry and ventilated area. Handling: Keep
Waste material may be disposed of in an approved landfill or may be
work areas clean and remove settled dust.
incinerated under conditions which meet Federal, State and local
________________________________________________________________
environmental regulations.
________________________________________________________________ XIII. PHYSICAL HAZARD_____________________________________
Flash Point: N/A, Auto Ignition Temperature: 650-800 F (343-427 C);
VII. HAZARDOUS IDENTIFICATION ____________________________
Flammable Limits (STP): N/A, toxic fumes are released in fire situations,
Inhalation: Dust exposure from Aerofix is very low; however, dust may
Stability: Stable under recommended storage conditions, Polymerization:
cause irritation to upper respiratory tract. Eye contact: No significant
Will not occur.
signs of any adverse health hazards are expected to occur as a result of
_______________________________________________________________
eye contact. Skin Contact: Essentially no-irritation to skin. Minor
XIV. OTHER INFORMATION__________________________________
mechanical injury may occur. Ingestion: Practically non-toxic.
The information supplied herein is related to material specified and may
__________________________________________________________
not be valid if used in combination with other materials or processes.
VIII. FIRST AID MEASURES___________________________________
Further, the information contained here is believed to be reliable and
Inhalation: Remove to fresh air if effects occur. If irritation persists,
based on correct state of our knowledge; however, no guarantees of any
consult a physician.
kind can be given as to its accuracy.
Ingestion: No adverse effects anticipated by this route except for the
hazard of choking. Eye: Flush eyes with plenty of water for at least 5
minutes. Skin: Wash off in flowing water or shower.
__________________________________________________________
IX. DISPOSAL CONSIDERATION______________________________
Waste material may be disposed of in an approved landfill or may be
incinerated under conditions which meet Federal, State and local
environmental regulations.