POLYURETHANE FOAM SYSTEMS
440 Conestogo Road
Waterloo, Ontario, N2L 4E2
Phone: 519 884-0688, Fax: 519 884-7300
MATERIAL SAFETY DATA SHEET
PRODUCT ?POLARFOAM PF-7300-0 SOYA
1. General Information WHMIS Classification
Manufacturer: Demilec, Broisbriand, Quebec Class D, Division 2B
Emergency Number: Canutec ?1 6l3 996-6666
Product Name: Resin Polarfoam PF-7300 Soya
Chemical Name: Polarfoam Soya
2. Hazardous Ingredients
Components CAS # % WEEL(AIHA)-
TWA- 8 hr.
1,1,1,3,3-Pentafluoropropane 460-73-1 7-13 300 ppm.
Trans 1,2 dichloroethylene 156-60-5 1-5 200 ppm*
Polyols blend N/A 40-70 N/A
Tertiary amine blend N/A 1.0-5.0 N/A
Tris-iso-chloropropyl phosphate 13674-84-5 7-13 Not listed
3. Physical Properties
Physical State: Peach liquid
Odour: Ester odour
Boiling Point: N/D
Freezing Point: N/D
Vapour Pressure: 7-9 psig at 25癈 (77癋), Static
Vapour Density: 4.6 (1,1,1,3,3,-Pentafluoropropane)
Specific Gravity: 1.2 @ 25癈 (77癋)
Solubility in Water: Moderate
4. Fire & Explosion Data
Flash Point: >200癋 (93癈)
Auto Ignition Temperature: N/D
Upper flammable limit (% vol.): N/D
Lower flammable limit (% vol.): ND
Extinguishing Media: Dry chemical, carbon dioxide, chemical foam and water spray.
Special Fire Fighting Procedures: Full emergency equipment with self-contained breathing
apparatus should be worn by fire fighters for protection against suffocation and possible toxic
decomposition products. Use cold water to cool fire-exposed containers. Heat will c;ause pressure
build up and may cause explosive rupture. A solid stream of water directed into hot burning liquid
could cause frothing.
5. Reactivity Data
Stability: Stable under normal storage conditions. See section 10.
Incompatibility (Material to avoid): Alkali or alkaline earth materials, (A1,Zn,Be,Cu), strong acids
and strong oxidizing agents. This material reacts rapidly with isocyanate.
Hazardous Decomposition Products: By high heat and fire: carbon monoxide, carbon dioxide,
oxides of nitrogen, ammonia, aldehydes, ketones & low molecular weight organic fragments.
Hazardous Polymerization: Will not occur.
6. Health Hazard Data
Eye Contact: Product liquids, aerosols or vapours are irritating. Vapours may cause a transient
condition known as glaucopsia, resulting in a blurring of vision against a bluish haze and the
appearance of halos around bright objects.
Skin Contact: May cause moderate irritation, defatting and dermatitis. May cause allergic skin
reaction.
Ingestion: May cause nausea, abdominal pains, vomiting and diarrhea. May also cause irritation to
throat, esophagus and stomach.
Inhalation: At high concentrations, fluorocarbons can lead to light-headedness, giddiness, shortness
of breath and possible narcosis. There have been reports that exposure to high concentrations of
fluorocarbons may include cardiac arrhythmia in some individuals. Vapourization of excessive
amounts of the fluorocarbon components can delete or replace oxygen necessary for breathing.
Excessive inhalation of vapours can cause respiration irritation, dizziness, headache, nausea and
asphyxiation.
7. First Aid Procedures
Eye Contact: Flush with running water for at least 15 minutes, holding eyelids open. Obtain medical
attention.
Skin Contact: Remove contaminated clothing. Wash affected areas with soap and water for at least
15 minutes. Wash contaminated clothing before reuse.
Ingestion: Obtain immediate medical attention from physician. Treat any ill effects symptomatically
and supportively.
Inhalation: Remove patient to an area free from further exposure, fresh air. Administer artificial
respiration if not breathing. If breathing is difficult, give oxygen. Obtain immediate medical attention.
8. Spill or Leak Procedures
Action to take for Spills/Leaks: Ventilate. Eliminate all sources of ignition. Utilize recommended
protective clothing. Dike area to avoid spreading. Absorb with sawdust, vermiculite or other
absorbent material. Collect and contain in suitable containers.
Clean-Up: Wash down surfaces with soap and warm water.
Waste Disposal: Dispose of waste according to federal, provincial and local regulations. Empty
containers must be handled with care due to product residue. Do not heat or cut empty containers with
electric or gas torch.
Polarfoam PF-7300-0 Soya, MSDS, Page 2
9. Handling Precautions
Eye Protection: Use liquid chemical goggles. Eyewash fountain and emergency shower should be in
close proximity.
Skin Protection: Use protective clothing impervious to chemicals. Selection of specific items such as
gloves (butyl or nitrile rubber), boots or apron will depend on operation. Practice good hygiene, wash
hands thoroughly before handling any food.
Respiratory Protection: An air-supplied respirator should be worn during liquid atomization and
when the product is being heated or in environments of high concentrations above the TLV.
Ventilation: Ventilation is necessary during processing. Local exhaust should be used to maintain
levels below the TWA-8hr. If it is not, an air-supplied respirator should be worn by all the people
located in the atomization area..
10. Storage and Handling
Storage Temperature (Min.-Max.): 15 - 25癈 (59-77癋).
Precaution to be taken in Storage and Handling: Store in tightly closed containers in a cool, dry
place. This product is hygroscopic. Avoid breathing vapours and contact with eyes or skin. Use only
with adequate ventilation. Employee education and training are important. Maintain good personal
hygiene.
11. Shipping Data
Technical Shipping Name: Polyol blend, Polarfoam PF-7300-0 Soya
T.D.G. Classification: Non-regulated
IMO Non-regulated
IATA/ICAO CLASS Non-regulated
12. Regulatory Information
All ingredients are listed on the DSL (Domestic Substance List)
13. Preparation
By: Demilec Inc.
Date: May 10, 2006
Polarfoam PF-7300-0 Soya, MSDS Page 3
|