PRO CHEM, INC. MATERIAL SAFETY DATA SHEET HEALTH 2
1475 BLUEGRASS LAKES PKWY.
INSTA-SEAL / 1464
ALPHARETTA, GA 30004 FIRE 4
EMERGENCY/INFO # (800) 241-8180
DECEMBER 2009 REACTIVITY 0
ADDITIONAL EMERGENCY # INFO TRAC 1-800-535-5053
PAGE 1 P.P.E. B
Complies With USDL Safety and Health Regulations, (29 CFR 1910.200)
EXTINGUISHING MEDIA: Dry Chemical. CO2. Halogenated Extinguishing Agent. Stop Gas Flow.
SECTION 1 ?Chemical and Company Identification
SPECIAL FIREFIGHTING PROCEDURES: Gas fires should not be extinguished unless the gas flow
PRODUCT DESCRIPTION: Elastomer
can be stopped immediately. Allow the fire to burn itself out. If the source cannot be shut off
SECTION 2 ?Composition on Ingredients immediately, all equipment and surfaces exposed to the fire should be cooled with water to prevent
over-heating, flash-backs, or explosions. Control fire until gas supply can be shut off. Use proper
NAME CAS # PEL TLV
protective equipment. Use fresh air respirator when exposure to hazardous concentrations of toxic
Xylene 1330-20-7 100 ppm 100 ppm
gases is possible.
TWA of 100 ppm (375 mg/m3) TWA of 50 ppm (147 mg/m3)
Aromatic Hydrocarbon 108-88-3
FIRE FIGHTING: Use water spray to cool fire exposed surfaces and to protect personnel. Isolate
Aliphatic Hydrocarbon 110-54-3 500 ppm 50 ppm
"fuel" supply from fire. Use foam, dry chemical, or water spray to extinguish fire. Avoid spraying water
Poly (Butadiene-co-styrene) 9003-55-8 Not Established Not Established
directly into storage containers due to danger of boiling over. This liquid is volatile and gives off
Ceramic Microspheres 66402-68-4 Not Applicable Not Applicable
3 3
invisible vapors. Either the liquid or vapor may settle in low areas or travel some distance along the
Titanium Dioxide 13463-67-7 10 mg/m 10 mg/m
N-Tallowalkyl Trimethylene 61791-53-5 Not Determined Not Determined ground or surface to ignition sources where they may ignite or explode.
Diamines Ole.
SECTION 6 ?Accidental Release Measures
80.00 mg/m3 10.00 mg/m3
Inorganic Metal Oxide 7631-86-9
Hydrocarbon Propellant 68476-86-8 800 ppm 800 ppm STEPS TO BE TAKEN IN CASE CONTAINER IS PUNCTURED AND MATERIAL IS RELEASED:
"*" If present, IARL, NTP and OSHA carcinogens and chemical subject to this reporting requirements of SARA TITLE III, SECTION 313
Clean up area by mopping or with absorbent materials and place in closed container for disposal.
are identified in this section.
Consult Federal, State, and local disposal authorities.
SECTION 3 ?Hazards Information
SECTION 7 ?Handling and Storage
GENERAL: This material is an aspiration hazard and defats the skin. Breathing vapors of high
HANDLING STORAGE AND DECONTAMINATION PROCEDURES: When utilizing pressurized
concentrations may cause CNS depression.
containers follow standard safety practices for handling aerosols.
EYE CONTACT: Slightly irritating but does not injure eye tissue.
GENERAL COMMENTS: Do not store at temperatures above 120F. Odor is not an adequate
SKIN CONTACT: Low order of toxicity. Frequent or prolonged contact may irritate and cause
warning of potentially hazardous concentrations in air. Releases of these gases may cause a
dermatitis. Skin contact may aggravate an existing dermatitis condition.
flammable atmosphere with explosion potential.
INHALATION: High vapor/aerosol concentrations (greater than approximately 100 ppm) are irritating
PRECAUTIONARY STATEMENTS: Please read and follow the directions on the product label. They
to the eyes and the respiratory tract, may cause headaches, dizziness, anesthesia,
are your best guide to using this product in the most effective way, and give the necessary safety
drowsiness, unconsciousness, and other central nervous system effects, including
precautions to protect your health.
death.
INGESTION: Small amounts of this product aspirated into the respiratory system during ingestion or
SECTION 8 ?Exposure Controls/Personal Protection
vomiting may cause mild to severe pulmonary injury, possibly minimal toxicity.
PRECAUTIONS:
SECTION 4 ?First Aid Measures SPECIAL PRECAUTIONS: Health studies have shown that many hydrocarbons pose potential
human health risks which may vary from person to person. As a precaution, exposure to liquids,
EYE CONTACT: Flush eyes with large amounts of water until irritation subsides. If irritation
vapors, mists or fumes should be minimized.
persists, get medical attention.
PERSONAL PROTECTION: For open systems where contact is likely, wear safety glasses with
SKIN CONTACT: Flush with large amounts of water; use soap if available. Remove grossly
side shields, long sleeves, and chemical resistant gloves. Where concentrations in air may
contaminated clothing, including shoes, and launder before reuse.
exceed the limits, work practice or other means of exposure reduction are not adequate,
INHALATION: Using proper respiratory protection, immediately remove the affected victim from
NIOSH/MSHA approved respirators may be necessary to prevent overexposure by inhalation.
exposure. Administer artificial respiration if breathing is stopped. Keep at rest. Call
VENTILATION: The use of mechanical dilution ventilation is recommended whenever this product
for prompt medical attention.
is used in a confined space, is heated above ambient temperatures, or is agitated.
INGESTION: If swallowed, DO NOT induce vomiting. Keep at rest. Get prompt medical attention.
VENTILATION REQUIREMENT: Use adequate level exhaust ventilation. Note: Where carbon
SECTION 5 ?Fire Fighting Measures monoxide may be generated, special ventilation may be required. Local exhaust recommended when
appropriate to control employee exposure.
FLASH POINT (N/A): Level 3 Aerosol
RESPIRATORY PROTECTION: Based on contamination level and working limits of the respirator,
EXPLOSIVE LIMIT (PRODUCT): LOWER: N/D UPPER: N/D
use a respirator approved by NIOSH/MSHA.
FIRE AND EXPLOSION HAZARDS: This product releases Flammable Vapors at well below ambient
EYES: Face shield and goggles or chemical goggles should be worn.
temperatures and readily forms flammable mixtures with air exposed to an ignition source. It will burn
GLOVES: Impervious gloves should be worn. Gloves contaminated with the product should be
in the open or be explosive in confined spaces. Its vapors are heavier than air and may travel long
discarded. Polyfluorinated polyethylene has been suggested.
distances to a point of ignition, and then flash back. Alkaline/chlorine gas mixtures have produced
explosions.
THIS INFORMATION MUST BE ON ALL MSDS'S COPIED AND DISTRIBUTED FOR THIS MATERIAL.
NO WARRANTY IS EXPRESSED/IMPLIED REGARDING THE ACCURACY OF THIS DATA OR
RESULTS OBTAINED FROM USE. PROCHEM ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE TO USER. VENDEE/USER ASSUMES ALL RISKS ASSOCIATED
WITH USE.
PRO CHEM, INC. MATERIAL SAFETY DATA SHEET HEALTH 2
1475 BLUEGRASS LAKES PKWY.
INSTA-SEAL / 1464
ALPHARETTA, GA 30004 FIRE 4
EMERGENCY/INFO # (800) 241-8180
DECEMBER 2009 REACTIVITY 0
ADDITIONAL EMERGENCY # INFO TRAC 1-800-535-5053
PAGE 2 P.P.E. B
Complies With USDL Safety and Health Regulations, (29 CFR 1910.200)
OTHER CLOTHING EQUIPMENT: Standard work clothing. Standard work shoes; discard if shoes SECTION 15 ?Regulatory Information
cannot be decontaminated. Store contaminated clothing in well ventilated cabinets or closed This MSDS complies with 29 CFR 1910.1200 (The Hazard Communication Standard)
containers. Wash contaminated clothing and dry before reuse. PROPOSITION 65: SEC05
RESPIRATORY PROTECTION: In situations where vapor concentrations exceed the recommended State of California SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT OF 1986.
exposure limits, a NIOSH approved organic vapor cartridge or air-supplying respirator should be worn. WARNING: In accordance with PROP 65, this product contains a chemical(s) known to the State
of California to cause cancer, birth defects and other reproductive harm.
SECTION 9 ?Physical and Chemical Properties CALIFORNIA AIR RESOURSE BOARD: This product complies with "REGULATION FOR
REDUCING VOLATILE ORGANIC COMPOUND EMISSIONS FROM CONSUMER PRODUCTS" for
BOILING POINT FOR PRODUCT: Not determined
the State of California.
VAPOR PRESSURE FOR PRODUCT: < 75 psi @ 60F
VAPOR DENSITY FOR PRODUCT: Heavier than air
SECTION 16 ?Other Information
SPECIFIC GRAVITY: 0.91 V.O.C. (GRAMS PER LITER): Not determined
WATER SOLUBILITY: Nil APPEARANCE: White rubber coating This Material Safety Data Sheet contains environmental, health and toxicology information for your
NON FLAT PAINT: MIR < 1.4 employees. Please make sure this information is given to them. It also contains information to help
you meet community Right To Know emergency response reporting requirements under SARA TITLE
SECTION 10 ?Stability and Reactivity III and many other laws. If you resell this product, this MSDS must be given to the buyer or the
information incorporated in your MSDS.
STABILITY: Stable
CONDITIONS TO AVOID: Temperatures above 130F.
The above information is based on the data of which we are aware and is believed to be correct as of
HAZARDOUS POLYMERIZATION: Will not occur.
the date hereof. Since the information contained herein may be applied under conditions beyond our
MATERIALS AND CONDITIONS TO AVOID INCOMPATIBILITY: Strong oxidizing agents.
control and with which we may be unfamiliar and since data made available subsequent to the date
HAZARDOUS DECOMPOSITION PRODUCTS: None
hereof may suggest modification of the information, we do not assume any responsibility for the results
of its use. This information is furnished upon condition that the person receiving it shall make his own
SECTION 11 ?Toxicological Information determination of the suitability of the material for his particular purpose.
No Data Available
SECTION 12 ?Ecological Information
No Data Available
SECTION 13 ?Disposal Consideration
WASTE DISPOSAL METHOD: Consult local authorities for proper waste disposal procedures. Empty
de-pressurized containers cannot be reused. Cans which are pressurized or contain liquid must be
disposed of in a permitted waste management facility. Consult Federal, State, and local disposal
authorities for approved procedures.
SECTION 14 ?Transport Information
D.O.T. PROPER SHIPPING NAME: ORM-D
Consumer Commodity
THIS INFORMATION MUST BE ON ALL MSDS'S COPIED AND DISTRIBUTED FOR THIS MATERIAL.
NO WARRANTY IS EXPRESSED/IMPLIED REGARDING THE ACCURACY OF THIS DATA OR
RESULTS OBTAINED FROM USE. PROCHEM ASSUMES NO RESPONSIBILITY FOR PERSONAL
INJURY OR PROPERTY DAMAGE TO USER. VENDEE/USER ASSUMES ALL RISKS ASSOCIATED
WITH USE.
|