MATERIAL SAFETY DATA SHEET
Johnsonite, Inc. Product: 940 Part B Adhesive
Supplier:
16910 Munn Road
Chagrin Falls, Ohio 44023
Section 1 ?Product Identification
Product Identifier\ Trade Name\ Material Name: Tarkett 940 Part B, DT 940 Part B,
Adhesive
Product Code\Internal ID: 940
Product Use or Description: Solvent free two component adhesive
MSDS Date: 10/10/06
Hazardous Materials Identification System (HMIS)
Health Hazard: 2 Chronic Hazard: No
Flammability: 0
Reactivity: 1
Personal Protection: H
For 24 HOUR MEDICAL AND DOT EMERGENCY For technical information, please call Technical
Services at: (800) 899-8916
RESPONSE COMMUNICATIONS AND INFORMATION, PLEASE CALL:
CANUTEC in Canada at (613) 996-6666 or (440) 543-8916
CHEMTREC in U.S.A. at (800) 424-9300 (440) 543-8920 ?Fax
Section 2 ?Chemical Composition \ Hazardous Ingredients
Ingredients CAS # % by Weight OSHA PEL ACGIH TLV
Nonyl Phenol 84852-15-3 40-70% N\Av N\Av
Aminoethylpiperazine 140-31-8 10-30% N\Av N\Av
Polyamine 68410-23-1 7-13% N\Av N\Av
2,4,6 90-72-2 1-5% N\Av N\Av
Trisdimethylaminomethyl
phenol
For California (Proposition 65): This product contains chemicals known to the state of California
to cause cancer, birth defects or other reproductive toxicity. All ingredients are listed within the
US TSA and Canadian DSL
Section 3 ?Hazards Identification
Route of Entry:
Eye Contact: Yes
Skin Contact: Yes
Inhalation: Yes
Ingestion: Yes
Effects of acute exposure to product: Inhalation or contact can cause irritation to eyes,
skin, nose, or throat to sensitive people. If
ingested can cause nausea, vomiting, gripping,
and diarrhea
Effects of chronic exposure to product: See Section 2
Other important hazards Allergies, skin, and respiratory disorders. Product
sensitivity.
N/Ap: Not applicable
N/Av: Not available
See last page for other abbreviations
MSDS #940 Part B 0207 Page 1 of 5
MATERIAL SAFETY DATA SHEET
Johnsonite, Inc. Product: 940 Part B Adhesive
Supplier:
16910 Munn Road
Chagrin Falls, Ohio 44023
Section 4 ?First Aid Measures
Eye Contact: Flush with cool water for 15 minutes while holding eyelid open. If
irritation persists, seek medical attention immediately.
Skin Contact: Avoid contact with skin. Remove contaminated clothing. Wash
affected area thoroughly with soap and water. If irritation persists,
seek immediate medical attention.
Inhalation: Remove to fresh air. If not breathing, trained personnel should
initiate artificial respiration and immediate medical attention
should be obtained.
Ingestion: Do not induce vomiting. Do not give anything by mouth to an
unconscious person. Seek medical attention immediately.
Section 5 ?Fire Fighting Measures
Fire hazards\conditions of flammability: Product will not burn until all water content has
evaporated.
Means of extinction: Water spray, carbon dioxide, dry chemical or
foam.
Flashpoint and method of determinations: Not established
Lower flammable limit (% by volume): Not established
Upper flammable limit (% by volume): Not established
Special fire-fighting procedures\equipment: Wear standard fire fighting gear with self-
contained breathing apparatus.
Unusual fire and explosion hazards: Some decomposition products may be harmful.
Section 6 ?Accidental Release Measures
Personal Precautions: Avoid prolonged skin contact and dusty conditions
Environmental precautions: Dispose of in accordance with local, state, provincial, and federal
regulations governing your location.
Spill response/cleanup: While using appropriate protective equipment, place spilled
material in poly drum, or container requirement by local disposal
company, and store in a safe place till material can be disposed
of in accordance with regulations.
Prohibited materials: Not established.
Section 7 ?Handling and Storage
Safe handling procedures: During work with dry product, it is recommended to wear NIOSH
approved particulate filter respirator rated N95.
Store at 60 - 95o F (15 ?35o C) and out of the sun. Use adequate
Storage requirements:
ventilation to avoid breathing vapors when cover is removed.
Incompatible materials: Strong oxidizing agents, strong acids, and strong bases.
Special packaging materials: Not established.
N/Ap: Not applicable
N/Av: Not available
See last page for other abbreviations
MSDS #940 Part B 0207 Page 2 of 5
MATERIAL SAFETY DATA SHEET
Johnsonite, Inc. Product: 940 Part B Adhesive
Supplier:
16910 Munn Road
Chagrin Falls, Ohio 44023
Section 8 ?Exposure Controls and Personal Protection
Ventilation and engineering controls: Use in WELL VENTILATED area only.
Respiratory protection: During work with dry product it is recommended to wear a
NIOSH approve particulate filter respirator rated N95
Protective gloves: Impervious (Nitrile, rubber, or better)
Eye protection: Safety glasses or goggles as necessary to prevent eye
contact.
Other protective equipment: As needed to minimize contact with skin.
Permissible exposure levels: Not established.
Section 9 ?Reactivity and Stability Data
Stability and reactivity (Polymerization): Stable
Conditions to avoid: None Known
Materials to avoid: Strong oxidizing agents, strong acids, and strong
bases.
Hazardous decomposition products: Carbon monoxide, carbon dioxide, oxides of nitrogen,
and other unidentified organic compounds.
Section 10 ?Reactivity and Stability Data
Physical form, color, and odor: Paste. Amine odor.
Odor threshold: Not established
pH: N/Ap
Boiling point: N/Ap
Melting point: N/Ap
Freezing point: N/Ap
Solubility in water: Negligible
Coefficient of oil/water distribution: Not established
Specific gravity or relative density (water = 1) .98
Vapor pressure (mmHg): N/Ap
Vapor density (air = 1) N/Ap
Evaporation rate (Butyl Acetate = 1): Not established
Calculated VOC: N/Ap
N/Ap: Not applicable
N/Av: Not available
See last page for other abbreviations
MSDS #940 Part B 0207 Page 3 of 5
MATERIAL SAFETY DATA SHEET
Johnsonite, Inc. Product: 940 Part B Adhesive
Supplier:
16910 Munn Road
Chagrin Falls, Ohio 44023
Section 11 ?Toxicological Information
LD50 (species and route): N/Av
LC50 (species and route): N/Av
Toxicological data: N/Av
Carcinogenicity: No
Reproductive toxicity: N/Av
Teratogenicity: N/Av
Mutagenicity: N/Av
Irritancy of product: Potential skin, eye respiratory irritant to
sensitive individuals.
Sensitization of product: Product sensitivity.
Conditions aggravated by exposure: Nausea, vomiting, nose and throat irritation,
and eye and skin irritation.
Name of toxicologically synergistic products: N/Av
Section 12 ?Ecological Information
Environmental effects: N/Av
Important environmental characteristics: N/Av
Aquatic toxicity: N/Av
Section 13 ?Waste Disposal
Handling for disposal: Dispose of in accordance with local, state, provincial, and federal
regulations governing your location.
Methods of disposal: Dispose of in accordance with local, state, provincial, and federal
regulations governing your location.
Section 14 ?Transportation Information
Transportation of Dangerous Good (TDG) Information;
Shipping name: Corrosive Liquid, NOS
Class: 8
UN number: 2735
Packing group: III (contains Polyamine liquid)
49 CFR information;
Shipping name: Corrosive Liquid, NOS
Class: 8
UN number: 2735
Packing group: III (contains Polyamine liquid)
International Dangerous Goods information
IMO: Not established
ICAO: Not established
Other information Not established
Section 15 ?Regulatory Information
WHMIS information WSHMIS classification: D2B; E
CEPA information All ingredients are listed with the Canadian DSL
TSCA information All ingredients are listed within the US TSCA
N/Ap: Not applicable
N/Av: Not available
See last page for other abbreviations
MSDS #940 Part B 0207 Page 4 of 5
MATERIAL SAFETY DATA SHEET
Johnsonite, Inc. Product: 940 Part B Adhesive
Supplier:
16910 Munn Road
Chagrin Falls, Ohio 44023
Section 16 ?Others Information
Certificate of origin Made in Canada
Prepared by: Technical Services
Telephone number: (440) 543-8916
Preparation date: 10/10/06
Abbreviations
ACGIH American Conference of Governmental Industrial Hygienists
ASTM American Society for Testing and Materials
CEPA Canadian Environmental Protection Act
CFR Code of Federal Regulations (Transportation in USA)
IARC International Agency for Research on Cancer
ICAO International Civil Aviation Organization
IMO International Maritime Organization
MSHA Mine Safety and Health Administration
NBUAC Normal Butyl Acetate
NIOSH National Institute for Occupational Safety and Health
NTP National Toxicology Program (U.S.A.)
OSHA Occupational Safety and Health Administration (U.S.A.)
PEL Permissible Exposure Limit
TLV Threshold Limit Value
TSCA Toxic Substance Control Act
TWA Time Weighted Average
WHMIS Workplace Hazardous Materials Information System
STEL Short-Term Exposure Limit
References
1. Suppliers' raw materials MSDS
2. ACGIH, Threshold Limit Values and Biological Exposure Indices for 1988
3. The Sigma-Aldrich Library of Chemical Safety Data, Second Edition, 1988
th
4. N.Irving Sax, Dangerous Properties of Industrial Materials, 7 Edition, Van Nostrand Reinhold, 1984
5. Health Canada, Reference manual for the WHMIS Requirements of the Hazardous Products Act and
Controlled Products Regulation updated March 22, 2001
Information on this form is offered in good faith as typical values and not as a product specification. No warranty, either
expressed or implied is hereby made. The recommended industrial hygiene and safe handling procedures are believed to
be generally applicable. However, each user should review these recommendations in the specific context of the intended
use and determine whether they are appropriate.
N/Ap: Not applicable
N/Av: Not available
See last page for other abbreviations
MSDS #940 Part B 0207 Page 5 of 5
|