OATEY EPOXY PUTTY
Latest Revision Date...02/27/01
Section 1 IDENTITY OF MATERIAL
TRADE NAME OATEY EPOXY PUTTY
PRODUCT NUMBERS 31270, 48033
FORMULA N/A
SYNONYMS N/A
SECTION 2 HAZARDOUS INGREDIENTS
INGREDIENTS % CAS NUMBER SEC 313
Epoxy Resin 10-30% 25068-38-6 No
2, 4, 6 ?Tri Dimethylaminomethyl Phenol 1- 3% 90-72-2 No
Crystalline Silica 10-15% 14808-60-7 No
Zinc Sulfide 0.5-3% 1314-98-3 Yes
Non Hazardous Ingredients:
Talc 30-50% 14807-96-6 No
Sodium Calcium Magnesium Silicate 15-25% 65997-17-3 No
Aluminum Flake 0.2-2% 7429-90-5 No
Amorphous silica 0.25-2% 67762-90-7 No
SECTION 3 KNOWN HAZARDS UNDER 29 CFR 1910.1200
HAZARDS YES NO HAZARDS YES NO
Combustible Liquid X Skin Hazard X
Flammable Material X Eye Hazard X
Pyrophoric Material X Toxic Agent X
Explosive Material X Highly Toxic Agent X
Unstable Material X Sensitizer X
Water Reactive Material X Kidney Toxin
Oxidizer X Reproductive Toxin X
Organic Peroxide X Blood Toxin X
Corrosive Material X Nervous System Toxin X
Compressed Gas X Lung Toxin X
Irritant X Liver Toxin X
Carcinogen NTP/IARC/OSHA X
(see SECTION 6)
SECTION 4 REGULATION
CHEMICAL TLV (TWA) PEL STEL Hazard Action
Level
Crystalline Silica 0.10 mg/m3 0.10 mg/m3 N/A N/A
Tri Dimethylaminomethyl Phenol 5.00 ppm N/A N/A N/A
Zinc Sulfide 5.00 mg/m3 5.00 mg/m3 N/A N/A
SECTION 5 REGULATED IDENTIFICATION
DOT PROPER SHIPPING Pipe, fitting or tool compounds
NAME
DOT HAZARD CLASS N/A
SHIPPING ID NUMBER N/A
EPA HAZARDOUS WASTE ID U101 & U069
NUMBER
EPA HAZARD WASTE CLASS Toxic Waste
SECTION 6 EFFECTS OF EXPOSURE
ENTRY ROUTE INHALE - YES INGEST - YES SKIN - YES EYE - YES
INHALATION If heated, fumes may cause respiratory irritation.
SKIN Heated fumes or direct contact may cause irritation.
EYE Heated fumes or direct contact may cause irritation.
INGESTION May irritate mouth, throat or gastrointestinal tract.
TARGET ORGANS Skin, Eye
WARNING This product contains trace amounts of crystalline silica, a chemical known by the
state of California to cause cancer. The chystalline silica in this product is
encapsulated in the epoxy resin and could only be liberated by sanding or abraing, and
then not as pure crystalline silica. Appropriate precautions, however, should be taken,
if the product is sanded or abraded to preclude personnel from breathing the dust.
SECTION 7 EMERGENCY AND FIRST AID PROCEDURES - 303/623-5716 COLLECT
SKIN If irritation arises, wash thoroughly with soap and water. Seek medical attention if irritation
persists.
EYES If fumes cause irritation, move to fresh air and irrigate eyes with water for 15 minutes. If
irritation persists, seek medical attention.
INHALATION Move to fresh air. If breathing is difficult, give oxygen. If not breathing, give artificial
respiration. Keep victim quiet and warm. Call a poison control center or physician
immediately.
INGESTION Drink water and call a poison control center or physician immediately. Avoid alcoholic
beverages. Never give anything by mouth to an unconscious person.
SECTION 8 PHYSICAL AND CHEMICAL PROPERTIES
NFPA HAZARD HEALTH 1 SPECIAL 1 FLAMMABILITY 1 STABILITY 0
SIGNAL
BOILING POINT N/A
MELTING POINT N/A
VAPOR PRESSURE N/A
VAPOR DENSITY N/A
(AIR = 1)
VOLATILE N/A
COMPONENTS
SOLUBILITY IN Insoluble
WATER
PH N/A
SPECIFIC GRAVITY 2.18
EVAPORATION Nil
RATE
APPEARANCE Black and white stripes
ODOR Mercaptan (sulfur-like)
WILL DISSOLVE IN Ethyl Alcohol and Aromatic solvents
MATERIAL IS Paste
SECTION 9 FIRE AND EXPLOSION HAZARD DATA
FLAMMABILITY LEL = N/A UEL = N/A
FLASHPOINT AND N/A
METHOD USED
STABILITY Stable. CONDITIONS TO AVOID: N/A HAZARDOUS DECOMP.
PRODUCTS: CO, Aldehydes, acids and oxides of sulfur and nitrogen.
HAZARDOUS Will not occur. CONDITIONS TO AVOID: Mixing of large mass of material may
POLYMERIZATION generate excessive heat.
INCOMPATIBILITY/ None
MAT. TO AVOID
SPECIAL FIRE FIGHTING FOR SMALL FIRES: Use dry chemical, CO(2), water or foam extinguisher.
PROCEDURE FOR LARGE FIRES: Evacuate area and call fire department immediately.
SECTION 10 SPILL AND DISPOSAL INFORMATION
SPILL OR LEAK Ventilate area, stop leak if it can be done without risk. Take up with sand, earth or other
PROCEDURES absorbing material.
WASTE DISPOSAL Dispose of according to local, state and federal regulations.
SECTION 11 SAFE USAGE DATA
PROTECTIVE EYES: Safety glasses with side shields. RESPIRATORY: None required for normal
EQUIPMENT TYPES use. GLOVES: Polyethylene for prolonged use. OTHER: None.
VENTILATION GENERAL MECHANICAL: None. LOCAL EXHAUST: Only if above 100 degrees F.
PRECAUTIONS HANDLING AND STORAGE: Do not store at temperatures exceeding 90 degrees F for
optimum shelf life.
SECTION 12 MANUFACTURER OR SUPPLIER DATA
FIRM NAME & MAILING OATEY CO., 4700 West 160th Street, P.O. Box 35906, Cleveland, Ohio 44135
ADDRESS
OATEY PHONE NUMBER (216) 267-7100
EMERGENCY PHONE (303) 623-5716 COLLECT
NUMBER
SECTION 13 DISCLAIMER
The information herein has been compiled from sources believed to be reliable, up-to-date, and is accurate to the
best of our knowledge. However, Oatey cannot give any guarantees regarding information from other sources, and
expressly does not make warranties, nor assumes any liability for its use.
|