M743-2005 B EPOXY PUTTY HARDENER
MATERIAL SAFETY DATA SHEET
RPM Wood Finishes Group
3194 Hickory Boulevard
Hudson, North Carolina 28638
828-728-8266
EMERGENCY PHONE (CHEM TREC): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-800-424-9300
FOR ALL INTERNATIONAL TRANSPORTATION ACCIDENTS. . . . . . . . . . . . . . . . .1-703-527-3887 (collect)
Health: 2 Flammability: 1 Reactivity 1
PRODUCT NAME: M743-2005 B EPOXY PUTTY HARDENER
I. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
REVISION DATE: 28/05/04
SUPERCEDES: None
MSDS NO. M743-2005 B
II. COMPOSITION/INFORMATION ON INGREDIENTS
CHEMICAL NAME % CAS # PEL
Magnesium Silicate Hydrate 41-50 14807-96-6 see Table Z-3
mercaptan-terminated polymer 41-50 PROPRIETARY No PEL established
TDMAMP 1-10 90-72-2 No PEL established
Quartz <1 14808-60-7 see Table Z-3
III. HAZARDS IDENTIFICATION
Inhalation., Skin contact., Ingestion., Eye contact.
Routes of Entry:
Respiratory disease including asthma and bronchitis. Eye disease.
Medical Conditions Aggravated:
Immediate (Acute) Health Effects
Can cause mechanical irritation if dusts are generated. Harmful if inhaled. Chronic
Inhalation:
lung disease (silicosis) and/or lung cancer may result from prolonged/repeated
breathing of the dust of this material. Can cause minor respiratory irritation,
dizziness, weakness, fatigue, nausea, and headache.
Substance may cause slight skin irritation. No hazard in normal industrial use.
Skin Contact:
Corrosive to skin tissue. Can cause chemical burns. Can cause minor skin irritation,
defatting, and dermatitis.
Can cause mechanical irritation if dusts are generated. No hazard in normal industrial
Eye Contact:
use. Corrosive to eye tissue. Can cause severe irritation, tearing, and burns that can
quickly lead to permanent injury including blindness. Can cause minor irritation,
tearing and reddening.
M743-2005 B EPOXY PUTTY HARDENER Page 1 of 5
No component(s) in this product is known to be absorbed through the skin. No
Skin Absorption:
absorption hazard in normal industrial use.
Harmful if swallowed. Mildly irritating to mouth, throat, and stomach. Can cause
Ingestion:
abdominal discomfort.
Target Organ Acute Toxicity:
Talc (containing no asbestos and less CVS, eyes, respiratory system
than 1% quartz)
Silica, crystalline respiratory system, eyes (in animals: lung cancer)
Long-Term (Chronic) Health Effects:
Carcinogenicity:
No information available.
Reproductive and Developmental
Toxicity:
No data available to indicate product or any components present at greater than 0.1%
Mutagenicity:
is mutagenic or genotoxic.
Upon prolonged and/or repeated exposure, can cause minor respiratory irritation,
Inhalation:
dizziness, weakness, fatigue, nausea, and headache.
Upon prolonged or repeated contact, corrosive to skin tissue. Can cause chemical
Skin Contact:
burns.
Upon prolonged or repeated contact, may become corrosive to eye tissue. Can cause
Eye Contact:
severe irritation, tearing, and burns that can lead to permanent injury including
blindness.
Skin sensitization, characterized by redness, inflammation, itching and/or burning
Skin Absorption:
may result from prolonged or repeated contact with this material. Upon prolonged or
repeated exposure, no hazard in normal industrial use.
Eyes. Respiratory Tract.
Target Organ Chronic Toxicity:
No additional health information available.
Supplemental Health Hazard
Information:
IV. FIRST AID
Remove to fresh air. If not breathing, give artificial respiration. If breathing is
Inhalation:
difficult, give oxygen. Get immediate medical attention. This material does not
present a hazard if inhaled. Remove individual to fresh air after an airborne exposure
if any symptoms develop, as a precautionary measure.
Immediately flush with plenty of water. After initial flushing, remove any contact
Eyes:
lenses and continue flushing for at least 15 minutes. Have eyes examined and tested
by medical personnel. Immediately flush eyes with plenty of water for at least 20
minutes retracting eyelids often. This corrosive material can cause immediate and
permanent eye damage. Tilt the head to prevent chemical from transferring to the
uncontaminated eye. Get immediate medical attention and monitor the eye daily as
advised by your physician.
M743-2005 B EPOXY PUTTY HARDENER Page 2 of 5
Wash with soap and water. Wash with soap and water under a drench shower.
Skin Contact:
Remove contaminated clothing, launder immediately, and discard contaminated
leather goods. Get medical attention immediately. Wash with soap and water. Get
medical attention if irritation develops or persists.
No hazard in normal industrial use. Do not induce vomiting. Seek medical attention
Ingestion:
if symptoms develop. Provide medical care provider with this MSDS.
No additional first aid information available.
Notes to MD:
V. FIRE FIGHTING MEASURES
Flammability Summary:
o
>200 (CALC.) F
Flash Point:
0.0 @ 77?F
Upper Flammable/Explosive
Limit, % in air:
0.0 @ 77?F
Lower Flammable/Explosive
Limit, % in air:
Use process enclosures to control the level of dust in the air.
Fire Hazards:
Use methods suitable to fight surrounding fire.
Extinguishing Media:
Hazardous Combustion Products: Carbon dioxide, Carbon monoxide
VI. ACCIDENTAL RELEASE MEASURES
Exposure to the spilled material may be irritating or harmful. Follow personal
Health Consideration for Spill
Response: protective equipment recommendations found in Section VIII of this MSDS.
Additional precautions may be necessary based on special circumstances created by
the spill including; the material spilled, the quantity of the spill, the area in which the
spill occurred. Also consider the expertise of employees in the area responding to the
spill.
Prevent the spread of any spill to minimize harm to human health and the
Spill Mitigation Procedures
General Methods: environment if safe to do so. Wear complete and proper personal protective
equipment following the recommendation of Section VIII at a minimum. Dike with
suitable absorbent material like granulated clay. Gather and store in a sealed container
pending a waste disposal evaluation.
VII. HANDLING AND STORAGE
Avoid contact with material. Minimize dust generation and accumulation. Harmful or
Handling:
irritating material. Avoid contact and avoid breathing the material. Use only in a well
ventilated area.
Keep container closed when not in use. Store in a cool dry place. Isolate from
Storage:
incompatible materials.
VIII. ENGINEERING CONTROLS AND PERSONAL PROTECTIVE EQUIPMENT
Check ventilation codes. No exposure limits exist for the constituents of this product.
Engineering Controls:
General room ventilation might be required to maintain operator comfort under
normal conditions of use.
M743-2005 B EPOXY PUTTY HARDENER Page 3 of 5
Protective Equipment
Respirators should be selected by and used under the direction of a trained health and
Respiratory Tract:
safety professional following requirements found in OSHA's respirator standard (29
CFR 1910.134) and ANSI's standard for respiratory protection (Z88.2-1992). A
written respiratory protection program, including provisions for medical certification,
training, fit testing, exposure assessments, maintenance, inspection, cleaning, and
convenient, sanitary storage should be implemented.
Wear chemically resistant safety glasses with side shields when handling this product.
Eyes:
Wear additional eye protection such as chemical splash goggles and/or face shield
when the possibility exists for eye contact with splashing or spraying liquid, or
airborne material. Do not wear contact lenses. Have an eye wash station available.
Avoid skin contact by wearing chemically resistant gloves, an apron and other
Skin:
protective equipment depending upon conditions of use. Inspect gloves for chemical
break-through and replace at regular intervals. Clean protective equipment regularly.
Wash hands and other exposed areas with mild soap and water before eating,
drinking, and when leaving work.
IX. PHYSICAL DATA
PASTE
Physical State:
STRONG SOLVENT
Odor:
100.0000
Solids Vol %:
100.0000
Solids Wt %:
0.0000
Material VOC lbs/gal:
0.0000
Material VOC gms/l:
0.000
Coatings VOC lbs/gal:
0.00
Coatings VOC gms/l:
13.4608
Weight per gallon:
X. STABILITY AND REACTIVITY
Stable. Stable under normal conditions.
Stability Information:
Contamination. None known.
Conditions to Avoid:
Strong oxidizing agents. Metals.
Chemical Incompatibility:
Hazardous Polymerization will not occur.
Hazardous Polymerization:
XI. TOXICOLOGICAL INFORMATION
Chemical Name CAS Number LD50/LC50
Phenol, 2,4,6- 90-72-2 Oral LD50 Rat : 1200 mg/kg
tris(dimethylaminomethyl)-
XII. ECOLOGICAL INFORMATION
No data available. This material is not expected to be harmful to the ecology.
Overview (for ingredients):
M743-2005 B EPOXY PUTTY HARDENER Page 4 of 5
XIII. DISPOSAL CONSIDERATIONS
Mixing spent or discarded material with other materials may render the mixture
Waste Description for Spent
Product: hazardous. Perform a hazardous waste determination on mixtures. Spent or discarded
material is non-hazardous according to environmental regulations.
Comply with all Local, State, Federal, and Provincial Environmental Regulations.
Disposal Methods:
Dispose of in a landfill. Disposal is not likely to be regulated.
Components Subject to USEPA Land Disposal Restrictions:
No chemicals subject to land disposal restrictions. %
XIV. TRANSPORTATION INFORMATION
NON REGULATED
DOT
See 49CFR 172.101 for Special Provisions, Packaging, and Quantity Limitations.
XV. REGULATORY INFORMATION
Chemical Name Regulation CASRN %
No 313-listed chemicals in this product SARA 313 Reportable:
14807-96-6 49.67
Magnesium Silicate Hydrate New Jersey Right To Know:
PROPRIETARY 45.12
mercaptan-terminated polymer New Jersey Right To Know:
90-72-2 5.16
TDMAMP New Jersey Right To Know:
14808-60-7 0.05
Quartz New Jersey Right To Know:
XVI. ADDITIONAL INFORMATION
IMPORTANT: WHILE THE DESCRIPTIONS, DATA AND INFORMATION
Other Information:
CONTAINED HEREIN ARE PRESENTED IN GOOD FAITH AND BELIEVED TO BE
ACCURATE, IT IS PROVIDED FOR YOUR GUIDANCE ONLY. BECAUSE MANY
FACTORS MAY AFFECT PROCESSING OR APPLICATION/USE, WE RECOMMEND
THAT YOU PERFORM AN ASSESSMENT TO DETERMINE THE SUITABILITY OF A
PRODUCT FOR YOUR PARTICULAR PURPOSE PRIOR TO USE. NO WARRANTIES
OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING FITNESS FOR A
PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED, DATA
OR INFORMATION SET FORTH. IN NO CASE SHALL THE DESCRIPTIONS,
INFORMATION,OR DATA PROVIDED BE CONSIDERED A PART OF OUR TERMS
AND CONDITIONS OF SALE. FURTHER, THE DESCRIPTIONS, DATA AND
INFORMATION FURNISHED HEREUNDER ARE GIVEN GRATIS. NO OBLIGATION
OR LIABILITY FOR THE DESCRIPTION, DATA AND INFORMATION GIVEN ARE
ASSUMED. ALL SUCH BEING GIVEN AND ACCEPTED AT YOUR RISK.
MSDS glossary.
M743-2005 B EPOXY PUTTY HARDENER Page 5 of 5
|