MATERIAL SAFETY DATA SHEET
ALUMFAST?-H-455 8oz. ALUMINUM REPAIR KIT
RESIN
Section I. Product Identification and Use
Manufacturer's Name: HY-POXY SYSTEMS, INC.
Address (Number Street): 5555 Export Blvd.
Address (City, State, Zip): Savannah, GA 31408 U.S.A.
Telephone Number: 843 363-5681 FAX: 843 363 5682
Emergency Telephone Number: CHEMTREC 1-800-424-9300 OUTSIDE U.S.A.: 703-527-3887
Chemical Family: Metal Filled Epoxy Resin
Hazardous Materials Description and proper shipping name (49 CFR 172.101): Not
Regulated
TSCA Inventory: All of the ingredients are listed on the TSCA inventory.
HMIS Labeling: Health: 2 Flammability: 1 Reactivity: 0
Section II. Hazardous Ingredients I Identity Information
Ingredients CAS %WW OSHA PEL ACGIH TLV Other Limits
Numbers
BisphenolA/EpichlorohydrinResin 25068-38-6 50-60 N.E. N.E. None
Phenolformaldhyde polymer, 28064-14-4 2-3 N.E. N.E. None
Glycidyl Ether
Hydrophobic Silicon Dioxide, 67762-90-7 1-2 20mppcf 10mg/m3 None
Amorphous
Aluminum Powder 7429-90-5 40-50 N.E. 15mg/m3 None
Section III. Physical/ Chemical Characteristics
Vapor pressure (mmHg) @ 20癈: < 1mm
Boiling point (癋): > 500癋
Weight per gallon: 12.8lbs. Percent volatile by volume (%): 0
Vapor density (Air = 1): > 1 Evaporation rate (n-Butyl Acetate = 1): N.A.
Solubility in water: Insoluble Appearance and odor: Silver paste, no odor
N.E. = Not established N.A. = Not applicable
Date: MARCH 1, 2008 hy-poxy systems, inc. p.o. box 6988 hilton head, sc 29938 usa tel. 843 363 5681 fax: 843 363-5682
www.hypoxy.com
1
MATERIAL SAFETY DATA SHEET
Section IV. Fire and Explosion Hazard
Flash point (method used): > 450癋 (PMCC) Flammable limits: Upper: N.E. Lower: N.E.
Extinguishing media: Use water fog, foam, carbon dioxide (CO2) or dry chemical
Special fire fighting procedures: Wear self-contained breathing apparatus and complete personal
protective equipment. Remove all ignition sources. Use a water spray to cool fire exposed
containers.
Unusual fire and explosive hazards: None known
N.E. = Not established N.A. = Not applicable
Section V. Health Hazard Data
Primary route(s} of entry: Inhalation, eyes
Health hazard/effects of over exposure:
Inhalation: Heated vapors may cause respiratory irritation.
Eyes: Moderately irritating.
Skin: Mildly irritating. May cause allergic reaction evidenced by rashes.
Ingestion: No specific information. Slightly toxic.
Chronic Effects of Overexposure: Prolonged contact with the skin may result in skin irritation and
sensitization.
Carcinogenicity: This material is not considered to be carcinogenic by NTP, IARC or OSHA.
Mutagenicity (Ames Test): Both positive and negative results for CAS# 25068-38-6.
Medical conditions aggravated by exposure: Pre-existing eye, skin and respiratory disorders may
be aggravated by exposure to this product. Pre-existing skin or lung allergies may increase the
chance of developing increased allergy symptoms.
Emergency and first aid procedures:
Inhalation: In case of exposure to a high concentration of vapor or mist, remove person to fresh
air. Get medical attention if effects persist. Administer oxygen if necessary.
Eyes: Flush with plenty of water for at least 15 minutes and seek immediate medical attention.
Skin: Remove contaminated clothing and wash contact area with soap and water. Wash clothing
before reuse and discard contaminated leather articles. Get medical attention if swelling or
reddening occurs.
Ingestion: If appreciable quantities are swallowed, seek medical attention. Do not induce vomiting.
Dilute by giving water or milk to drink if victim is conscious.
Section VI. Reactivity Data
Stability: Stable Conditions to avoid: Excessive heat.
Incompatibility (Materials to avoid}: Strong oxidizing agents and mineral acids. Uncontrolled curing
with amine curing agents in masses greater than 2 inches thick.
Hazardous decomposition products: Fumes produced when heated to decomposition may include:
carbon monoxide, carbon dioxide, ammonia, and nitrogen oxides.
Hazardous polymerization: Will not occur.
Date: MARCH 1, 2008 hy-poxy systems, inc. p.o. box 6988 hilton head, sc 29938 usa tel. 843 363 5681 fax: 843 363-5682
www.hypoxy.com
2
MATERIAL SAFETY DATA SHEET
Section VII. Precautions for Safe Handling and Use
Steps to be taken in case material is released or spilled: Dike spill. Absorb with inert material and
collect for disposal. Flush area with water. Prevent washings from entering waterways.
Waste disposal methods: Incinerate or use biological treatment in accordance with local, state and
federal regulations. Dispose of as a hazardous waste according to local, state and federal
regulations.
RCRA Hazardous Waste No.: N.A.
CERCLA Reportable Quantity: If this product becomes a waste, it would not be a hazardous waste
by RCRA criteria (40 CFR 261). Place in an appropriate disposal facility in compliance with local
regulations.
SARA TITLE III Chemicals: This product has been reviewed according to the EPA "Hazard
Categories" promulgated under Sections 311 and 312 of the Superfund Amendment and
Reauthorization Act of 1986 (SARA Title III) and is considered under applicable definitions, to meet
the following categories: An immediate health hazard. This product contains no ingredients subject
to SARA Title III Section 313.
Section VIII. Control Measures
Respiratory Protection: Wear a properly fitted NIOSH/MSHA approved respirator whenever
exposure to vapor/mist is likely unless levels are below applicable limits.
Ventilation: Local exhaust is recommended when appropriate to control employee exposure.
Mechanical is not recommended as the sole means of controlling employee exposure.
Protective gloves: For operations where contact can occur, wear impervious gloves (neoprene,
nitrile}.
Eye protection: Chemical splash goggles or safety glasses with side shields.
Other protective equipment: For operations where contact can occur, coveralls, apron and rubber
foot covering are recommended. A safety shower and eye wash facility should be available.
Work/hygienic practices: Wash hands with soap and water after use and/or before breaks, lunch
and at the end of work
Section IX. Preparation Date of MSDS
The foregoing technical information and recommendations are compiled from sources that are
believed to be accurate and reliable. However, they are supplied without warranty or guarantee of
any kind either expressed or implied. The purchaser is responsible for selecting and determining
the suitability of products for purchaser's particular needs and we disclaim any responsibility for
improper applications or misuse of our products in any manner whatsoever.
Alumfast?8oz. H-455 Resin MSDS
Date: MARCH 1, 2008 hy-poxy systems, inc. p.o. box 6988 hilton head, sc 29938 usa tel. 843 363 5681 fax: 843 363-5682
www.hypoxy.com
3
|