Huntsman Advanced Materials Americas Inc.
24-Hour Emergency Phone: 1-888-354-3323
MSDS No: 5773
Effective Date: 2/26/04 Material Safety Data Sheet
Health: 2*
1. PRODUCT IDENTIFICATION 1
Flammability: 1
2 0
Reactivity: 0
Trade Name: Fastweld 10 Resin
Personal Protection:
Chemical Family: Epoxy
HMIS RATING
NFPA RATING
Intended Use or Product Type:
Adhesive resin
2. COMPOSITION / INFORMATION ON INGREDIENTS
O CAS No. CHEMICAL IDENTITY EXPOSURE LIMITS CARCINOGEN
S STATUS
H ACGIH OSHA MFR. IARC NTP OSHA
A TWA STEL PEL STEL
* 1333-86-4 Carbon Black 3.5 NE 3.5 NE NE Yes NR NR
mg/m3 mg/m3
Common Carbon black
Name:
* 14808-60-7 Quartz (SiO2) 0.05 NE 0.1 NE NE Yes Yes NR
mg/m3 mg/m3
Common Crystalline silica
Name:
* 25068-38-6 Phenol, NE NE NE NE NE NR NR NR
4,4'-(1-methylethylidene)bis-,
polymer with
(chloromethyl)oxirane
Common Bisphenol A diglycidyl ether
Name: polymer
* 71011-27-3 Quarternary ammonium NE NE NE NE NE NR NR NR
compounds, bis(hydrogenated
tallow alkyl) dimethyl, chlorides,
compounds with hectorite
Common Bentonite clay
Name:
* = OSHA Hazardous Ingredient
3. HAZARDS IDENTIFICATION
Emergency Overview: Causes skin and eye irritation. May cause allergic skin reaction.
Printed: 29/03/2004 Page 1 of 6
Fastweld 10 Resin Huntsman Advanced Materials
Effective Date: 2/26/04 Americas Inc.
Primary Route(s) of Entry: Dermal; heated product may produce inhalable vapors.
Carcinogenicity (NTP, IARC, OSHA): This product contains carbon black which is classified as a carcinogen by IARC (2B,
possibly carcinogenic to humans) and NIOSH.
Chronic: Contains crystalline silica. Breathing dust may cause cancer and delayed lung injury. This product contains Crystalline
silica. Repeated inhalation of respirable free Crystalline silica dust may cause delayed lung injury (silicosis) and cancer.
4. FIRST AID MEASURES
Ingestion: If conscious, give 2 - 4 glasses of water to drink. Do not induce vomiting. Call a physician.
Skin: Immediately wash with soap and water. Remove contaminated clothing and launder before reuse. Destroy contaminated
shoes.
Inhalation: Remove to fresh air. Call a physician.
Eyes: Immediately flush eyes with water for at least 15 minutes. Call a physician.
Overexposure Effects: Causes skin and eye irritation. May cause allergic skin reaction.
Medical Conditions Aggravated by Exposure: Skin and eye conditions.
Additional Information: Referral to a physician is recommended if there is any question about the seriousness of any injury.
5. FIRE FIGHTING MEASURES
277癋 (136 癈)
Flash Point:
PMCC
Flash Point Method Used:
Not established
Flammable Limits in Air (Lower - % by volume):
Not established
Flammable Limits in Air (Upper - % by volume):
Fire Fighting Extinguishing Media: Carbon dioxide, dry chemical, foam, water.
Fire Fighting Equipment: Use self-contained breathing apparatus.
Fire and Explosion Hazards: Decomposition and combustion products may be toxic.
6. ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Remove spillage by absorbing in absorbent material.
7. HANDLING AND STORAGE
Signal Word: Warning!
Precautions: Can cause skin irritation, eye irritation, and allergic skin reaction. Avoid contact with eyes, skin, and clothing. Wash
thoroughly after handling. Notice! Contains crystalline silica. Breathing dust may cause cancer and delayed lung injury.
Printed: 29/03/2004 Page 2 of 6
Fastweld 10 Resin Huntsman Advanced Materials
Effective Date: 2/26/04 Americas Inc.
Other Handling Information: Crystalline silica may be generated when machining cured products. Overexposure may create
possible cancer and silicosis hazard.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Skin Protection: Wear impermeable gloves.
Respiratory Protection: Use NIOSH approved organic vapor cartridge respirator when vapor/mist exposure is likely.
Eye Protection: Wear splash-proof chemical goggles.
Engineering Controls: General mechanical and local exhaust in accordance with ACGIH recommendations.
9. PHYSICAL AND CHEMICAL PROPERTIES
Black
Color:
Mild
Odor:
Paste
Physical State:
Insoluble
Solubility in Water:
< 0. at 25癈 (77 癋)
Vapor Pressure:
1.43 - 1.53 (water = 1)
Specific Gravity:
Not Determined
Boiling Point:
Not Determined
Evaporation Rate:
Not Determined
Vapor Density:
0 g/L
VOC:
Not Determined
pH:
Percent Volatile: Negligible.
10. STABILITY AND REACTIVITY
Conditions to Avoid: Excessive heat for prolonged periods of time.
Stability: Stable.
Incompatibility: Strong oxidizers, acids and bases.
Hazardous Decomposition Products: Combustion may form toxic materials, such as carbon dioxide, carbon monoxide.
Hazardous Polymerization: Will not occur.
11. TOXICOLOGICAL INFORMATION
Sensitization: Possible in susceptible individuals.
Carcinogenicity: This product contains carbon black which is classified as a carcinogen by IARC (2B, possibly carcinogenic to
humans) and NIOSH. This product contains crystalline silica. Repeated inhalation of respirable free crystalline silica dust may cause
delayed lung injury (silicosis) and cancer.
Printed: 29/03/2004 Page 3 of 6
Fastweld 10 Resin Huntsman Advanced Materials
Effective Date: 2/26/04 Americas Inc.
Skin Irritation: Irritant.
Eye Irritation: Irritant.
12. ECOLOGICAL INFORMATION
13. DISPOSAL CONSIDERATIONS
Waste Disposal Method: Consult qualified local or corporate personnel for method that will comply with local, state and federal
health and environmental regulations.
14. TRANSPORT INFORMATION
DOT: Non-Bulk
Resin compounds, N.O.I.
Proper Shipping Name:
Department of Transportation: Not regulated as a hazardous material by the U.S. Dept. of Transportation (DOT) 49 CFR 172.101
hazardous materials table.
15. REGULATORY INFORMATION
US Federal Regulations:
Occupational Safety and Health Act (OSHA): This Material Safety Data Sheet (MSDS) has been prepared in compliance with the
federal OSHA Hazard Communication Standard 29 CFR 1910.1200. This product is considered to be a hazardous chemical under
that standard.
Resource Conservation and Recovery Act (RCRA): Not a hazardous waste under RCRA (40 CFR 261).
SARA Title III: Section 313 Toxic Chemical List (TCL): This product does not contain any chemicals for routine annual toxic
chemical release reporting under Section 313 (40 CFR 372).
TSCA Section 8(b) - Inventory Status: All chemical components of this product are in compliance with TSCA inventory
requirements.
TSCA Section 12(b) - Export Notification: This product does not contain any chemical(s) that are subject to a Section 12(b) export
notification.
State Regulations:
California Proposition 65: The following is required composition information. This product contains the following chemical(s)
which are currently listed on the California list of Known Carcinogens and Reproductive Toxins:
Chemical Name: Quartz (SiO2)
Common Name: Crystalline silica
CAS Number: 14808-60-7
Percent in Composition: 0.51 % by wt
Comment: Warning! This chemical is known to the State of California to cause cancer.
Printed: 29/03/2004 Page 4 of 6
Fastweld 10 Resin Huntsman Advanced Materials
Effective Date: 2/26/04 Americas Inc.
Chemical Name: Arsenic
CAS Number: 7440-38-2
Percent in Composition: 0 % by wt
Comment: Warning! This chemical is known to the State of California to cause cancer and birth defects or other reproductive harm.
Chemical Name: Lead
CAS Number: 7439-92-1
Percent in Composition: 0 % by wt
Comment: Warning! This chemical is known to the State of California to cause cancer and birth defects or other reproductive harm.
Chemical Name: Oxirane, (chloromethyl)-
Common Name: Epichlorohydrin
CAS Number: 106-89-8
Percent in Composition: 0 % by wt
Comment: Warning! This chemical is known to the State of California to cause cancer and birth defects or other reproductive harm.
Pennsylvania Right-to-Know: The following is required composition information:
Chemical Name: Phenol, 4,4'-(1-methylethylidene)bis-, polymer with (chloromethyl)oxirane
Common Name: Bisphenol A diglycidyl ether polymer
CAS Number: 25068-38-6
Comment: Not on Pennsylvania Hazardous Substance List
Chemical Name: Limestone
Common Name: Calcium carbonate
CAS Number: 1317-65-3
Comment: Hazardous Substance
Chemical Name: Quarternary ammonium compounds, bis(hydrogenated tallow alkyl) dimethyl, chlorides, compounds with hectorite
Common Name: Bentonite clay
CAS Number: 71011-27-3
Comment: Not on Pennsylvania Hazardous Substance List
16. OTHER INFORMATION
5773
MSDS No:
Dianne Blessing
Approved By:
EH&S Specialist
Title:
Disclaimer: The information and recommendations contained herein are based upon tests in controlled laboratory conditions, are
believed to be correct, and are provided for the sole purpose of hazard communication as part of Huntsman's product safety program.
This product has not been tested for, and therefore is not recommended or suitable for, uses for which prolonged contact with mucous
membranes, abraded skin, or blood is intended or likely, or for uses for which implantation within the human body is intended, and
Huntsman assumes no liability for any such uses.
The information and recommendations contained herein are not intended to constitute performance information concerning the
product, which is available in separate technical data sheets available from Huntsman upon request. Users are urged, and are urged to
urge others who may come in contact with the product, to obtain and consult data sheets prior to purchase, use, transportation or
storage of the product.
Printed: 29/03/2004 Page 5 of 6
Fastweld 10 Resin Huntsman Advanced Materials
Effective Date: 2/26/04 Americas Inc.
HUNTSMAN MAKES NO REPRESENTATION OR WARRANTY, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY, QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. HUNTSMAN'S LIABILITY IS
STRICTLY LIMITED TO REIMBURSEMENT OF BUYER'S PURCHASE PRICE, OR IN HUNTSMAN'S DISCRETION
REPLACEMENT, OF THE PRODUCT IN RESPECT OF WHICH SUCH CLAIM IS MADE. HUNTSMAN'S LIABILITY IS
STRICTLY LIMITED BY LEGAL NOTICES IN TECHNICAL DATA SHEETS, PRODUCT LITERATURE AND/OR SALE
DOCUMENTS. The foregoing DISCLAIMERS and LIMITATION OF LIABILITY supercede inconsistent or contradictory
provisions in Buyer's documents.
USER SHOULD CONSULT A LEGAL ADVISOR OR THE APPROPRIATE GOVERNMENTAL AGENCY TO DETERMINE
THE APPLICABILITY OR EFFECT OF ANY LAW OR REGULATION WITH RESPECT TO THE PRODUCT. HUNTSMAN
DOES NOT UNDERTAKE TO FURNISH ADVICE ON SUCH MATTERS.
Printed: 29/03/2004 Page 6 of 6
|