MATERIAL SAFETY DATA SHEET
EU-100 Lightweight HARDENER COMPONENT
Page 1 of 2
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: AMERICAN SAFETY TECHNOLOGIES INC. TRADE NAME: EU-100 Lightweight
565 Eagle Rock Ave. HARDENER COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: EPOXY
DOT SHIPPING CLASSIFICATION (49 CFR 172.101): (Not Regulated) HMIS RATING:
TRANSPORTATION EMERGENCY NO. (CHEMTREC): 1-800-424-9300 HEALTH =2
MFG'S DUNN'S NO: 002-171-213 FLAMMABILITY=1
REACTIVITY =0
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT OR ORDER NO.
MIL-D-3135 Type I/II Class 2
PREPARED BY: J. Hermele DATE: 11/20/2002 REVISION: 0
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS NO. % WT. OSHA ACGIH
Propoxylated Triethylenetetramine 26950-63-0 >80 N.E. N.E.
Triethylene Tetramine 112-24-3 <20 N.E. N.E.
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING TOXIC CHEMICALS
SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND
COMMUNITY RIGHT-TO-KNOW ACT OF 1986 AND OF 40 CFR 372. THIS INFORMATION MUST BE INCLUDED ON
THE MSDS COPIED AND DISTRIBUTED FOR THIS MATERIAL.
(N.E. = Not Established)
CHEMICAL NAME CAS NUMBER WEIGHT %
None
SECTION 3: PHYSICAL DATA
BOILING POINT: > 200癋/93癈 SPECIFIC GRAVITY: 1.02
VAPOR PRESSURE: < 0.01mmHg @ 68 F/20 C MELTING POINT: N.A.
VAPOR DENSITY: N.A. (AIR = 1) EVAPORATION RATE: N.A. (Butyl Acetate = 1)
SOLUBILITY IN WATER: Miscible
APPEARANCE AND ODOR: Yellow Liquid, Amine Odor
(N.A. = Not Applicable)
SECTION 4: FIRE AND EXPLOSION HAZARD
FLASH POINT: > 340癋/171癈 PMCC FLAMMABLE LIMITS: LEL UEL
N.E. N.E.
EXTINGUISHING MEDIA: Carbon Dioxide, Foam, Dry Chemical or Water Spray.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self-contained breathing apparatus and complete personal
protective equipment where potential for exposure to vapors of products of combustion exists.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: Decomposition and combustion products may be toxic.
MATERIAL SAFETY DATA SHEET
EU-100 LITE AGGREGATE COMPONENT
Document #_______________________________________________ __________________Page 1 of 2_
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: ITW AMERICAN SAFETY TECHNOLOGIES TRADE NAME: EU-100 LITE
565 Eagle Rock Ave. AGGREGATE COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: N.A.
DOT SHIPPING CLASSIFICATION (49 CFR 172.101): (Not Regulated) HMIS RATING:
TRANSPORTATION EMERGENCY NO. (CHEMTREC): 1-800-424-9300 Health =1
MFG'S DUNN'S NO: 002-171-213 Flammability =0
Reactivity =0
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT OR ORDER NO.
MIL-D-3135 Type I/II Class 2
PREPARED BY: J. Hermele DATE: 11/20/2002 REVISION: 0
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION _______
INGREDIENTS CAS NO. % WT. OSHA ACGIH OTHER
8HrTWA 8HrTWA
Alumina Silicate 68131-74-8 40% 10mg/m3 10mg/m3 (Respirable Dust)
Amorphous Silica 1332-09-8 60 % 80mg/m3 10mg/m3 ( Inhalable)
3 mg/3 (Respirable)
Quartz 14808-60-7 <0.1 10mg/m3 0.05 mg/m3 (Respirable)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING TOXIC CHEMICALS SUBJECT TO THE
REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF
1986 AND OF 40 CFR 372. THIS INFORMATION MUST BE INCLUDED ON THE MSDS COPIED AND DISTRIBUTED FOR THIS
MATERIAL.
CHEMICAL NAME CAS NUMBER WEIGHT %
None
SECTION 3: PHYSICAL DATA
BOILING POINT: N.A. SPECIFIC GRAVITY: 1.7
VAPOR PRESSURE: N.A. MELTING POINT: N.A.
VAPOR DENSITY: N.A. (AIR = 1) EVAPORATION RATE: N.A. (Butyl Acetate = 1)
SOLUBILITY IN WATER: Insoluble
APPEARANCE AND ODOR: White or Gray, No Odor
(N.A. = Not Applicable)
SECTION 4: FIRE AND EXPLOSION HAZARD
FLASH POINT: N.A. FLAMMABLE LIMITS: LEL UEL
N.A. N.A.
EXTINGUISHING MEDIA: N.A. (Can be used to smother fires).
SPECIAL FIRE FIGHTING PROCEDURES: None.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: None. Material is non-combustible.
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Dust may cause transient eye irritation.
Skin: Dust may cause transient skin irritation.
EU-100 LITE AGGREGATE COMPONENT
Page 2 of 2
SECTION 5: HEALTH HAZARD DATA (Cont'd).
HEALTH HAZARDS (ACUTE AND CHRONIC)
Inhalation: Health hazards occur from excessive inhalation. Irritation to upper respiratory tract
And lungs may result from accidental or chronic occupational exposure to the dust in
this product. Dust may also cause lung damage when inhaled.
Ingestion: No known adverse health effects.
CONDITIONS AGGRAVATED BY EXPOSURE: Respiratory Diseases.
CARCINOGENIC DATA: NTP ?No , IARC ?Vol.68(1997), In Group 3 (Not classifiable as to
carcinogenicity to humans. ?Not Regulated by OSHA.
OVEREXPOSURE EFFECTS: Exposure may result in coughing, wheezing, shortness of breath, tightness in
chest, irritation of the upper respiratory tract, and damage to lung tissue. Although the aggregates in this product
have less then 0.1% respirable crystalline silica content, grinding or milling during removal by mechanical
abrasion, may generate levels of crystalline silica in excess of 0.1%. Appropriate safety practices should be
followed to prevent inhalation of airborne dusts. The International Agency for Research on Cancer
("IARC") concluded that there was "sufficient evidence in humans for the carcinogenicity of crystalline silica in the
forms of quartz or crystobalite from occupational sources.", the overall IARC evaluation was that "crystalline
silica inhaled in the form of quartz or crystobalite from occupational sources is carcinogenic to humans ( Group
1). NTP, in its Ninth Annual Report on Carcinogens, has classified "silica, crystalline (respirable)" to be a
carcinogen." Crystalline silica is not regulated by OSHA as a carcinogen.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water to remove particles.
Skin: Wash with mild soap and water.
Inhalation: Remove to fresh air.
Ingestion: None.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: N.E.
INCOMPATIBILITY (Materials to Avoid): Strong Alkalies, Metallic Oxides at high temperatures and
Hydrofluoric Acid.
HAZARDOUS DECOMPOSITION PRODUCTS: Hydrofluoric Acid generates volatile Silicon Tetrafluoride.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Use respiratory protection for
airborne dust. Vacuum or scoop for recovery or disposal. Wetting spill with a water spray will help to keep dust
levels down; use good ventilation if possible.
WASTE DISPOSAL METHODS: Not considered a hazardous waste; can be used as a soil sweetener.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved disposable half-mask for dust/mist if required.
VENTILATION: Local exhaust as appropriate. Mechanical ventilation is recommended.
PROTECTIVE GLOVES: Leather or Rubber gloves.
EYE PROTECTION: Safety glasses or dust-tight goggles.
OTHER PROTECTIVE EQUIPMENT: An eye wash facility should be available in material handing area.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Use dustless system of storage and
handling. Keep well-ventilated.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
CALIFORNIA PROPOSITION 65 INFORMATION: WARNING! This product contains a chemical known to
the State of California to cause cancer and birth defects or other reproductive harm. (Silicon Dioxide:
Respirable Particles)
MATERIAL SAFETY DATA SHEET
EU-100 Lightweight BASE COMPONENT
Document # Page 1 of 1
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: ITW AMERICAN SAFETY TECHNOLOGIES TRADE NAME: EU-100 Lightweight
565 Eagle Rock Ave. BASE COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: EPOXY
DOT SHIPPING CLASSIFICATION: (Not Regulated) HMIS RATING:
TRANSPORTATION EMERGENCY NO. (CHEMTREC): 1-800-424-9300 Health =2
MFG'S DUNN'S NO: 002-171-213 Flammability =1
Reactivity =0
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT OR ORDER NO.
MIL-D-3135 Type I/II Class 2
PREPARED BY: J. Hermele DATE: 2/17/2004 REVISION: 0
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS NO. % WT. OSHA ACGIH OTHER
Epoxy Resin 25068-38-6 70-100 N.E. N.E. LD50RAT >5g/kg (Oral)
Aliphatic Monoglycidyl Ether 68609-97-2 0-30% N.E. N.E. LD50RAT >17g/kg (Oral)
(N.E. = Not Established)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING TOXIC
CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY
PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF 1986 AND OF 40 CFR 372. THIS
INFORMATION MUST BE INCLUDED ON THE MSDS COPIED AND DISTRIBUTED FOR THIS MATERIAL.
CHEMICAL NAME CAS NUMBER WEIGHT %
None
SECTION 3: PHYSICAL DATA
BOILING POINT: > 300癋/149癈 SPECIFIC GRAVITY: 1.1
VAPOR PRESSURE: < 1.0mmHg @ 68癋/20癈 MELTING POINT: N.A.
VAPOR DENSITY: N.A. (AIR = 1) EVAPORATION RATE: < 1.0(Butyl Acetate = 1)
SOLUBILITY IN WATER: Insoluble
APPEARANCE AND ODOR: Hazy Clear Liquid, Mild Odor
(N.A. = Not Applicable)
SECTION 4: FIRE AND EXPLOSION HAZARD
FLASH POINT: > 200癋/93癈 PMCC FLAMMABLE LIMITS: LEL UEL
N.E. N.E.
EXTINGUISHING MEDIA: Carbon Dioxide, Chemical Foam, Dry Chemical or Water Spray.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self-contained breathing apparatus and complete personal
protective equipment where potential for exposure to vapors of products of combustion exists.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: Decomposition and combustion products may be toxic.
EU-100 Lightweight BASE COMPONENT
Page 2 of 2
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin/Ingestion
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Irritant
Skin: Irritant. May cause allergic skin reaction which can be severe in certain individuals.
Inhalation: May cause nose and throat irritation.
Ingestion: No specific information available. Contains materials that may be slightly toxic.
CONDITIONS AGGRAVATED BY EXPOSURE: Allergy, eczema and other skin conditions.
CARCINOGENIC DATA: Not on NTP, IARC or OSHA lists.
OVEREXPOSURE EFFECTS: Irritation, sensitization and dermatitis.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water for at least 15 minutes and get medical attention.
Skin: Remove contaminated clothing and wash contact area with mild soap and water.
Inhalation: Remove to fresh air. If breathing is difficult, administer oxygen.
Ingestion: Give large quantities of water to dilute and induce vomiting. Get medical attention.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive Heat
INCOMPATIBILITY (Materials to Avoid): Strong Oxidizing Agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide and Carbon Dioxide.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Avoid all personal contact. Dike
Spill. Absorb with inert material and collect for disposal. Flush contaminated area with water; prevent
washings from entering waterways.
WASTE DISPOSAL METHODS: Dispose of in accordance with Federal, State and Local Regulations.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator with organic vapor cartridge if required.
VENTILATION: Mechanical ventilation and local exhaust are recommended. Mechanical exhaust is not
recommended as the sole means of controlling employee exposure.
PROTECTIVE GLOVES: Impervious gloves.
EYE PROTECTION: Chemical splash-proof goggles.
OTHER PROTECTIVE EQUIPMENT: In operations where contact may occur coveralls, apron and
impervious foot covering are recommended.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid all personal contact. Do not exceed
100癋/43癈 in storage area.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
* A safety shower and eye wash facility should be available to employees.
* Immediately remove and thoroughly launder contaminated clothing before reuse.
EU-100 Lightweight HARDENER COMPONENT
Page 2 of 2
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Moderate eye irritant, causes irritation, redness and discomfort which is transient.
Skin: Irritant. May cause sensitization and/or allergic skin reaction which can be severe in
certain individuals.
Inhalation: Causes upper respiratory tract irritation and mucous membrane irritation.
Ingestion: No specific information available. Contains material that may be slightly toxic.
CONDITIONS AGGRAVATED BY EXPOSURE: Allergy, eczema and other skin conditions.
CARCINOGENIC DATA: Not on NTP, IARC or OSHA lists.
OVEREXPOSURE EFFECTS: Irritation, sensitization and dermatitis.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water for at least 15 minutes. Get medical attention.
Skin: Remove contaminated clothing and wash contact area with mild soap and water. If
irritation develops or persists, get medical attention.
Inhalation: Remove to fresh air. If breathing is difficult, administer oxygen.
Ingestion: Get immediate medical attention. If conscious, give large quantities of water to dilute, but
do not induce vomiting.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive Heat
INCOMPATIBILITY (Materials to Avoid): Strong Oxidizing Agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide, Carbon Dioxide, Aldehydes and Oxides of
Nitrogen.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Avoid all personal contact. Dike
Spill. Absorb with inert material and collect for disposal. Flush contaminated area with water; prevent washings
from entering waterways.
WASTE DISPOSAL METHODS: Dispose of in accordance with Federal, State and Local Regulations.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator with organic vapor cartridge if required.
VENTILATION: Mechanical ventilation and local exhaust are recommended. Mechanical exhaust is not
recommended as the sole means of controlling employee exposure.
PROTECTIVE GLOVES: Impervious gloves.
EYE PROTECTION: Chemical splash-proof goggles.
OTHER PROTECTIVE EQUIPMENT: In operations where contact may occur, coveralls, apron and impervious
foot covering are recommended.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid all personal contact. Do not exceed
110 F/43 C in storage area.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
* A safety shower and eye wash facility should be available to employees.
* Immediately remove and thoroughly launder contaminated clothing before reuse.
|