Manufacturer:
Nox-Crete Manufacturing Inc.
1444 South 20th Street
OMAHA, NE 68108
Manufacturer Phone Number: 402-341-2080
Fax Number: 402-341-9752
E-Mail: corporate@nox-crete.com
Web Site: www.nox-crete.com
Emergency Phone Number
Chemtrec: 800-424-9300
Chemtrec Outside Of U.S.: 703-527-3887
Product Name: Silcoseal 2000 F
CAS Number: Not Established
Chemical Family: Water based concrete tilt-up bondbreaker emulsion
Product Code: SS2F
2. HazardS idEntiFication
ingredient caS
1-BUTANOL 71-36-3
AROMATIC SOLVENT 64742-95-6
AROMATIC SOLVENT 1335-20-7
MEDIUM ALIPHATIC SOLVENT NAPHTHA 64742-88-7
Primary Route(s) Of Entry
Eye Contact, Skin Contact, Ingestion, Inhalation
Eye Hazards: May cause eye irritation
Skin Hazards: May cause skin irritation.
Ingestion Hazards: Aspiration hazard if swallowed. Can enter lungs and cause damage.
Inhalation Hazards: Excessive vapor inhalation can cause anesthesia, headache, nausea and dizziness.
3. FirSt aid MEaSurES
In case of contact, hold eyelids apart and immediately flush. Get medical attention immediately if irritation develops and persists.
Skin: Remove contaminated clothing and shoes. Wash affected areas with soap and water. Wash clothing before reuse. Get medical
attention immediately if irritation (redness, rash, blistering) develops and persists.
Ingestion: If swallowed, do not induce vomiting. Get medical attention immediately.
Inhalation If irritation, headache, nausea, or drowsiness occurs, remove to fresh air. Get medical attention if breathing
becomes difficult or symptoms persist.
4. FirE FigHting MEaSurES
Flash Point: 95 癋 35 癈
Flash Point Method: PMCC
Fire And Explosion Hazards: Can form flammable mixtures with air and flash at room temperature. Explosive hazard in fire situation.
Vapor heavier than air may travel considerable distance to a source of ignition and flash back.
Extinguishing Media: Use CO2 (Carbon Dioxide), dry chemical, or foam.
Fire Fighting Instructions: Firefighters should wear self-contained breathing apparatus and full protective gear. Water can be used to
cool and protect exposed material. Avoid spreading burning liquid with water used for cooling purposes.
5. accidEntal rElEaSE MEaSurES
Eliminate any ignition source. Dike or impound spilled material. Contain and/or absorb spill with inert material (e.g. sand,
vermiculite). Collect into vapor tight containers and dispose of properly.
6. Handling and StoragE
Handling Precautions: Keep container closed when not in use. Use only with adequate ventilation. Prevent exposure to freezing
temperatures.
Storage Precautions: Store product in a cool, dry environment away from sources of ignition. Prevent exposure to freezing tempera-
tures.
Work/Hygienic Practices: Wash thoroughly with soap and water after handling.
7. ExPoSurE controlS/PErSonal ProtEction
Engineering Controls: Use with adequate ventilation to keep product vapor concentrations below specified TLV.
Eye/Face Protection: Chemical goggles and/or face shields are required to prevent potential eye contact, irritation or injury.
Skin Protection: Wear gloves and appropriate protective clothing as required to prevent skin contact. Wash exposed skin frequently
with soap and water. Soiled clothing should be laundered before reuse.
Respiratory Protection: General room ventilation is normally adequate. Avoid breathing the product mist. The use of a NIOSH
approved respirator is recommended whenever the airborne concentrations exceed the TLV.
Ingredient(s) - Exposure Limits
1-Butanol: 50 ppm
Aromatic Solvent: 100 ppm
Aromatic Solvent:100 ppm
Medium Aliphatic Solvent Naphtha:10 ppm
8. PHySical and cHEMical ProPErtiES
Appearance: White emulsion with mild solvent odor.
Chemical Type: Mixture
Physical State: Liquid
Boiling Point: 200-300 "F
Specific Gravity: Lighter than water
Packing Density: 8.05 lbs per gallon
Solubility: Miscible
Evaporation Rate: Slower than ether
VOC: Less than 600 grams per liter
Flash Point: 95 F (PMCC)
9. rEactivity/Stability
Stability: Stable
Hazardous Polymerization: Will not occur
Incompatible Materials: Strong oxidizing agents. Strong acids or bases and selected amines.
Hazardous Decomposition Products: Combustion may produce carbon monoxide, carbon dioxide, and various hydrocarbon deriva-
tives.
10. toxicological inForMation
Chronic/Carcinogenicity
No component of this product present at levels greater than 0.1% is identified as a carcinogen by the U.S. National Toxicology
Program, the U.S. Occupational Safety and Health Act, or the International Agency on Research on Cancer (IARC).
11. diSPoSal conSidErationS
Care must be taken to prevent environmental contamination from the use of this material. The user of this material has the respon-
sibility to dispose of unused material, residues and containers in compliance with ail applicable local, state and federal laws and
regulations regarding treatment, storage and disposal for hazardous and nonhazardous wastes.
12. tranSPort inForMation
Proper Shipping Name: Paint Related Material
13. rEgulatory inForMation
SARA Section 313 Notification
This product contains the following toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning
and Community Right-To-Know Act of 1986 and of 40 CFR 372. This information must be included in all MSDSs that are copied
and distributed for this material.
chemical cas # Max Weight %
Xylene 1330-20-7 Up To 5.2
Ethylbenzene 100-41-4 Up To 1.4
Butanol 71-36-3 Up To 2.8
HMIS
Health
Flammability 13
Reactivity 0
Personal Protection
The information contained herein is based on the data available to us and is believed to be correct. However, we make no war-
ranty, expressed or implied regarding the accuracy of this data or the results to be obtained from the use thereof. We assume no
responsibility for injury from the use of the product described herein.