MATERIAL SAFETY DATA SHEET Page 1 of 7
LUBRI-BOND 220 (BULK)
PRODUCT NAME: LUBRI-BOND 220 (BULK) HMIS CODES: HFRP
PRODUCT CODE: PLB220 230B
1. MANUFACTURING IDENTIFICATION
EVERLUBE PRODUCTS
100 COOPER CIRCLE
PEACHTREE CITY, GA 30269
EMERGENCY PHONE: CHEMTREC - 800-424-9300
DATE PREPARED: 5/6/2008
INFORMATION PHONE: (770) 261-4800
NAME OF PREPARER: CHEMICAL COMMUNICATIONS COOORDINATOR
2. HAZARDOUS INGREDIENTS
COMPONENT/EXPOSURE LIMITS CAS# % BY WT.
------------------------------------------------------------------------------
TOLUENE 108-88-3 35% - 40%
OSHA PEL 200.00 PPM-TWA
OSHA PEL 300.000 PPM-CEILING
OSHA VPEL 100.000 PPM-TWA
OSHA VPEL 150.000 PPM-STEL (SKIN)
ACGIH TLV 50.000 PPM-TWA (SKIN)
ACGIH TLV 150.000 PPM-STEL (SKIN)
XYLENE 1330-20-7 30% - 35%
ACGIH TLV: 100 PPM
OSHA PEL: 100 PPM
ACGIH STEL: 150 PPM
MOLYBDENUM DISULFIDE 1317-33-5 10% - 15%
ACGIH TWA I 10 mg/m3
ACGIH TWA R 3 mg/m3
ANTIMONY TRIOXIDE 1309-64-4 0% - 5%
ACGIH PEL-TWA: 0.5 mg/m3 as Sb
ACGIH TLV TWA: 0.5 mg/m3 as Sb
ETHYL BENZENE 100-41-4 0% - 5%
OSHA PEL 100 ppm-TWA
OSHA VPEL 100 ppm-TWA
OSHA VPEL 125 ppm-STEL
ACGIH TLV 100 ppm-TWA
ACGIH TLV 125 ppm-STEL
LEAD PHOSPHITE 12141-20-7 0% - 5%
ACGIH TLV-TWA: 0.15 MG/M3 (8 hrs), as Pb
BLV: 50 MMG/100G BLOOD
OSHA PEL: 0.05 MG/M3, AS Pb
MINERAL SPIRITS 8052-41-3 0% - 5%
ACGIH STEL N/E ppm
ACGIH TWA 100 ppm
OSHA PEL TWA 500 ppm
OSHA VPEL TWA 100 ppm
3. HAZARDS IDENTIFICATION
POTENTIAL EFFECTS OF SHORT-TERM (ACUTE) EXPOSURE:
Processing fumes may cause irritation of the eyes and respiratory
tract. Use with adequate ventilation. Avoid breathing process
fumes.
MATERIAL SAFETY DATA SHEET Page 2 of 7
LUBRI-BOND 220 (BULK)
In case of fire, toxic fumes of lead oxide may be emitted.
EYE CONTACT:
This material can cause eye irritation.
SKIN CONTACT:
Prolonged and repeated contact with the skin can cause defatting and
drying of the skin resulting in skin irritation and skin rash
(dermatitis).
INHALATION:
Inhalation of high concentrations of solvents may cause narcotic
effects such as headaches, dizziness, nausea, vomiting and coma.
INGESTION:
Can result in irritation of mouth, stomach tissue and digestive tract.
Vomiting may result in aspiration into the lungs can cause
chemical pneumonitis which can be fatal.
POTENTIAL EFFECTS OF LONG-TERM (CHRONIC) EXPOSURE:
No specific information is available regarding long-term exposure to
this material. Other information on any known toxic or chronic-
health effects of the material or its ingredients can be found in
Section 11 - Toxicological Information.
4. FIRST AID MEASURES
EYE CONTACT:
With eyelids open, immediately flush eyes with lots of lukewarm water
for at least 30 minutes. Get immediate Medical Assistance.
SKIN CONTACT:
Wash the skin thoroughly with plenty of water for at least 15 minutes,
using a mild and non-abrasive soap. Cold water may be used
Consult a doctor if irritation persists.
INHALATION:
Evacuate to fresh air and administer artificial respiration if
breathing stopped. Obtain Medical Aid.
INGESTION:
Never give anything by mouth if the victim is semi-conscious,
unconscious or convulsing.
Seek immediate medical attention.
Induce vomiting immediately by giving 2 glasses of water and
stimulating the uvula with a finger.
NOTE TO PHYSICIANS:
The main hazard following accidental ingestion is aspiration of the
liquid into the lungs producing chemical pneumonitis. If more
then 2.0 ml/Kg has been ingested, vomiting should be induced with
supervision. If symptons, such as loss of gag reflex, convulsions
or unconsciousness occur before vomiting, gastric lavage with a
cuffed endotracheal tube should be considered.
MATERIAL SAFETY DATA SHEET Page 3 of 7
LUBRI-BOND 220 (BULK)
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES:
Vapors may form, with air, an explosive mixture between lower and upper
explosive limits.
FLASH POINT (DEGREES F.) ..............: 45 F
FLASH POINT METHOD ....................: TCC
LOWER FLAMMABILITY LIMIT (% BY VOLUME).: 1.2
UPPER FLAMMABILITY LIMIT (% BY VOLUME).: 7.0
AUTO-IGNITION TEMPERATURE..............: n/a
HAZARDOUS DECOMPOSITON PRODUCTS:
Irritating and toxic fumes including the following may be released:
carbon monoxide, carbon dioxide, and zinc
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Avoid accumulation of water. Product will float on water and may
reignite on surface of water.
Closed containers may explode due to pressure build-up when
exposed to extreme heat.
DO NOT cut, drill, grind or weld near containers even when empty.
Residual product or vapours may ignite or explode.
Extinguish all nearby sources of ignition.
EXTINGUISHING MEDIA:
CO2, foam, dry chemical or halon
FIREFIGHTING PROCEDURES / EQUIPMENT:
Extinguish all nearby sources of ignition.
Use water spray to cool containers and structures exposed to
fire.
Fire-Fighters should wear self-contained breathing apparatus and
full protective equipment.
6. ACCIDENTAL RELEASE MEASURES
PERSONAL PRECAUTIONS:
Emergency personnel must wear the following protective equipement:
selfcontained breathing apparatus, protective clothing, safety
goggles and boots.
Evacuate all personnel not related to emergency procedures.
ENVIRONMENTAL PRECAUTIONS:
Prevent the product or the wash waters from entering the water system
or sewers.
US regulations require reporting spills of this material that
could reach any surface waters. In Canada, report to the
applicable provincial environment ministry.
SPILL RESPONSE / CLEANUP:
MATERIAL SAFETY DATA SHEET Page 4 of 7
LUBRI-BOND 220 (BULK)
SMALL SPILL:
Eliminate all sources of ignition, provide ventilation, contain spill
and absorb with inert absorbent.
Issue warning "Flammable". Isolate the hazard area and restrict
access.
Handle as highly flammable liquid.
Wear appropriate breathing apparatus (if applicable) and
protective clothing.
Prevent the spill or wash from entering sewers or watercourses.
LARGE SPILL:
Remove by mechanical means and place in containers.
7. HANDLING AND STORAGE
SAFE HANDLING PROCEDURES:
Maintain good personal hygiene. Avoid breathing processing vapours.
Avoid prolonged or repeated skin contact. Wash skin with soap and
water after handling. Wash contaminated clothing before re-use.
STORAGE REQUIREMENTS / CONDITIONS TO AVOID:
Keep containers closed (when not in use).
Keep away from heat, sparks and flames.
Store in a cool, dry, well ventilated area away from incompatible
materials.
Smoking in the area where this material is used should be
strictly prohibited.
DO NOT cut, drill, grind or weld near containers even when empty.
Residual product or vapours may ignite or explode.
INCOMPATIBLE MATERIALS:
Oxidisers, Strong Acids or Alkalies.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
VENTILATION AND ENGINEERING CONTROLS:
General mechanical ventilation or local exhaust should be suitable to
keep vapour concentrations below the threshold limit values.
All ventilation equipment must be explosion proof.
For personal entry into confined spaces (i.e. bulk storage tanks)
a proper confined space entry procedure must be followed
including ventilation and testing of tank atmosphere. Make-up air
should always be supplied to balance air exhausted.
Effective exhaust ventilation should always be provided to draw
fumes, vapors or dust away from workers to prevent routine
inhalation.
RESPIRATORY PROTECTION:
Use NIOSH/MSHA approved Cartridge Respirator or Mask to keep airborne
MATERIAL SAFETY DATA SHEET Page 5 of 7
LUBRI-BOND 220 (BULK)
mists and concentrations below the time weighted threshold limit
values.
SKIN PROTECTION AND GLOVES:
Use Chemically impermeable gloves (eg Neoprene or Nitrile) for skin
protection.
EYE PROTECTION:
Use chemical Safety Glasses/Goggles and Faceshields. Contact lenses
should not be worn without goggles.
OTHER PROTECTIVE EQUIPMENT:
Eye wash stations and safety showers in the workplace are recommended.
PERMISSIBLE EXPOSURE LEVELS:
PLEASE SEE SECTION 2, HAZARDOUS MATERIALS.
9. PHYSICAL AND CHEMICAL PROPERTIES
SPECIFIC GRAVITY .................: .99679
POUNDS PER GALLON ................: 8.3 lb/gl
VOLATILE (% BY VOLUME) ...........: Not available
VOLATILE (% BY WEIGHT) ...........: 75%
BOILING POINT (DEGREES F.) .......: 230F to 280F
VOC (EPA Method 24)...............: 745 grams/liter
MELTING POINT.....................: Not Established.
EVAPORATION RATE (BUTYL ACETATE=1): Faster than n-Butyl Acetate.
VAPOR PRESSURE (MM HG AT 20癋.)...: Not Available.
VAPOR DENSITY (AIR=1).............: Heavier than air.
SOLUBILITY IN WATER ..............: Slightly Soluble
PH ...............................: Not Applicable.
APPEARANCE AND ODOR ..............: Gray/black liquid, organic solvent odor
10. STABILITY AND REACTIVITY
STABILITY AND REACTIVITY:
Stable under normal conditions.
CONDITIONS TO AVOID:
Heat, sparks, open flames or other sources of ignition.
MATERIALS TO AVOID:
Oxidizers, Strong Acids or Alkalies.
HAZARDOUS POLYMERIZATION:
Will not occur.
11. TOXICOLOGICAL INFORMATION
LD50 / LC50:
Please see Section 2, Hazardous Ingredients.
TOXICOLOGICAL DATA:
Please see Section 2, Hazardous Ingredients.
CARCINOGENICITY:
NTP-Yes
IARC-Yes
MATERIAL SAFETY DATA SHEET Page 6 of 7
LUBRI-BOND 220 (BULK)
MUTAGENICITY:
None known.
SENSITIZATION TO MATERIAL:
None Known
CONDITIONS AGGRAVATED BY EXPOSURE:
May aggrevate pre-existing skin or respiratory disorders (bronchitis,
emphysema, hyper-reactivity) skin allergies, eczema.
SYNERGYSTIC MATERIALS:
None known
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL EFFECTS:
Do not allow product or runoff from fire control to enter storm or
sanitary sewers, lakes, rivers, streams, or public waterways.
Canadian and U.S. regulations require that environmental and/or
other agencies be notified of a spill incident. The spill area
must be cleaned and restored to the original condition or to the
satisfaction of authorities.
AQUATIC TOXICITY:
May be harmful to aquatic life.
13. WASTE DISPOSAL
WASTE MANAGEMENT:
Waste management priorities (depending on volumes and concentration of
waste) are: 1. Recycle (reprocess), 2. Energy recovery (cement
killns, thermal power generation), 3. Incineration, 4. Disposal
at a licensed waste disposal facility. Do not attempt to combust
waste on-site. Incinerate at a licensed waste disposal site with
approval of environment authority
14. TRANSPORT INFORMATION
TDG: PAINT RELATED MATERIAL
CLASS 3, UN1263, PACKING GROUP II
15. REGULATORY INFORMATION
WHMIS CLASSIFICATION:
CANADIAN WHMIS:
THIS PRODUCT HAS BEEN CLASSIFIED IN ACCORDANCE WITH THE HAZARD
CRITERIA OF THE CONTROLLED PRODUCTS REGULATIONS (CPR), AND THIS
MSDS CONTAINS ALL THE INFORMATION REQUIRED BY THE CPR.
OSHA REGULATED: YES
SARA:
IF THIS MATERIAL HAS ANY COMPONENTS WHICH ARE REPORTABLE UNDER SARA 313
THEY ARE SHOWN IN THE FOLLOWING LISTING. IF THE LISTING IS BLANK, THEN
THERE ARE NO REPORTABLE COMPONENTS.
COMPONENTS REPORTABLE UNDER SARA 313: CAS# % BY WT.
----------------------------------------------------------------------------
TOLUENE 108-88-3 35% - 40%
MATERIAL SAFETY DATA SHEET Page 7 of 7
LUBRI-BOND 220 (BULK)
XYLENE 1330-20-7 30% - 35%
ANTIMONY TRIOXIDE 1309-64-4 0% - 5%
ETHYL BENZENE 100-41-4 0% - 5%
LEAD PHOSPHITE 12141-20-7 0% - 5%
MINERAL SPIRITS 8052-41-3 0% - 5%
ALL COMPONENTS OF THIS PRODUCT ARE ON THE TSCA INVENTORY OR ARE EXCEMPT
FROM TSCA INVENTORY REQUIREMENTS
16. OTHER INFORMATION
TO THE BEST OF OUR KNOWLEDGE, THE INFORMATION AND RECOMMENDATIONS
CONTAINED HEREIN IS BELIEVED TO BE ACCURATE AT THE TIME OF
PREPARATION OR OBTAINED FROM SOURCES BELIEVED TO BE RELIABLE.
HOWEVER IT IS THE USER'S RESPONSIBILITY TO DETERMINE SAFETY, TOXICITY
AND SUITABILITY FOR HIS OWN USE OF THE PRODUCT. EVERLUBE PRODUCTS
ASSUMES NO RESPONSIBILITY. THE CUSTOMER OR RECIPIENT OF THIS MSDS
SHOULD ENSURE THAT THE INFORMATION CONTAINED IN THIS MSDS IS MADE
AVAILABLE TO ALL EMPLOYEES OR OTHER PERSONS WHOME HE KNOWS OR
BELIEVES WILL USE THIS MATERIAL.
|