MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 1 of 7
ny that
The compa
is now
this work
published mpany
venture co
in a joint
Tube Mills.
tralian
Material Safety Data Sheet
named Aus or sale
l support
r technica
Fo ntact
please co
enquiries
be Mills.
ustralian Tu
A
Uncontrolled Copy
TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP
HOLLOW SECTIONS
Infosafe MAD32 Issue May 2006 Status ISSUED by
No. Date ONESTNPM
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
Product Name TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SECTIONS
Product Code
Company
Name OneSteel Trading Pty Ltd - Newcastle Pipe Mills (ABN 50 007 519 646)
Address PO Box 156 Newcastle
NSW 2300
Emergency
Tel. 02 4935 5739
Telephone/Fax Tel: 02 4935 5118
Number Fax: 02 4935 5115
Recommended Fluid conveyance, structural, machinery, construction applications etc..
Use COATINGS USED: Red or blue pigmented or clear paint, or no coating.
Other Name Product Code
Names
TUBELINE CHS, TUBELINE RHS, TUBELINE
SHS, SCAFFOLDING CHS, SHOULDERED
CHS, RAIL, SILO SECTION, GROOVED CHS,
HIGH SPEED CONVEYOR TUBE, FIRELITE,
SUPER LIGHT, BORE CASING.
2. HAZARDS IDENTIFICATION
Hazard Not classified as hazardous
Classification
NON-HAZARDOUS SUBSTANCE.
NON-DANGEROUS GOODS.
Hazard classification according to the criteria of NOHSC.
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 2 of 7
Dangerous goods classification according to the Australia Dangerous Goods
Code.
Risk Phrase Not classified as hazardous
(s)
Safety
Phrase(s) S22 Do not breathe dust.
Other FROM HEAT GENERATED FUME ONLY: With burning or welding, moderate
Information amounts
of fume are emitted which contain mostly visible finely divided iron oxide
(Fe2O3) fume. Small amounts of ozone and other gases may be emitted.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Information CLEAR COATED: External clear coat, approx. 10 micrometre thick, of a water-
on borne modified alkyd resin paint (0-0.1 %)
Composition NOP: not oiled or painted except for end colour code (0-0.1 %)
PAINTED: External coating, approx.10 micrometre thick film of water borne
epoxy/ acrylic resin zinc phosphate primer, or approx.15 micrometre thick film
of solvent borne alkyd resin zinc phosphate primer (0-0.09 %)
Ingredients Name CAS Proportion
Steel 7439-89-6 95-100 %
Manganese 7439-96-5 0.2-1.3 %
Marking ink or paint as an 0-0.1 %
end colour code.
Coating 0-0.1 %
4. FIRST AID MEASURES
Inhalation It is unlikely that this product can be inhaled in the as supplied form.
If exposed to fume from welding operations, remove to fresh air.
Ingestion It is unlikely that this product can be ingested in the as supplied form.
Skin It is unlikely that this product will cause irritation to the skin in the as supplied
form.
For lacerations, clean and dress wound.
For burns, apply copious amounts of cool water.
Eye It is unlikely that this product will enter the eye(s) in the as supplied form.
If steel splinters enter the eye, obtain medical treatment immediately.
First Aid
Facilities Eye wash fountains and normal washroom facilities.
Advice to
Doctor Treat symptomatically.
5. FIRE FIGHTING MEASURES
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 3 of 7
Suitable
Extinguishing
Media Use appropriate fire extinguisher for surrounding environment.
Hazards from
Combustion
Products The product as supplied is inert.
Special
Protective
Equipment
for fire Fire-fighters should wear full protective clothing and self contained breathing
fighters apparatus (SCBA).
6. ACCIDENTAL RELEASE MEASURES
Emergency
Procedures Pick up mechanically or by hand tools.
7. HANDLING AND STORAGE
Precautions Always wash hands before eating, drinking, smoking or using the toilet. See
for Safe Section 8 Exposure Controls/Personal Protection for specific control
Handling recommendations.
Conditions
for Safe
Storage Store in a dry environment to prevent corrosion in storage.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
National Exposure Standards Name STEL (mgm3) STEL (ppm) TWA (mgm3) TWA
Steel 5
Manganese 3 1
Biological
Limit Values No biological limit allocated.
Other No exposure standards have been established for this material by the National
Exposure Occupational Health And Safety Commission (NOHSC). However, all exposure
Information should be kept to the least possible levels as over-exposure to any chemical
may result in enhancement of pre-existing adverse medical conditions and/or
allergic reactions. Exposure standards for individual constituents are listed
above.
TWA - the Time-Weighted Average airborne concentrations over an eight-hour
working day, for a five-day working week over an entire working life.
STEL (Short Term Exposure Limit) - the average airborne concentration over a
15 minute period which should not be exceeded at any time during a normal
eight-hour work day.
According to current knowledge these concentrations should neither impair the
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 4 of 7
health of, nor cause undue discomfort to, nearly all workers.
Peak Limitation - a ceiling concentration which should not be exceeded over a
measurement period which should be as short as possible but not exceeding
15 minutes.
'Sk' notice - absorption through the skin may be a significant source of
exposure. The exposure standard is invalidated if such contact should occur.
These Exposure Standards are guides to be used in the control of occupational
health hazards. All atmospheric contamination should be kept to as low a level
as is workable. Exposure Standards should not be used as fine dividing lines
between safe and dangerous concentrations of chemicals. They are not a
measure of relative toxicity.
Engineering No special ventilation is required for the product as supplied.
Controls For welding or cutting operations, local filtered extraction may be necessary to
maintain the air concentration of fumes below the National Exposure
Standards.
Dust from processing operations should not be allowed to build up in the
workplace and should be removed for disposal. If possible, cleanup should be
undertaken using a vacuum with a high efficiency filter. Ensure dust
generation during cleanup is minimized, using appropriate work practices.
Respiratory Not normally required. However, if engineering controls are not effective in
Protection controlling airborne exposure then respiratory protective equipment should be
used suitable for protecting against airborne contaminants. Final choice of
appropriate breathing protection is dependant upon actual airborne
concentrations and the type of breathing protection required will vary
according to individual circumstances. Expert advice may be required to make
this decision. Reference should be made to Australian Standards AS/NZS
1715, Selection, Use and maintenance of Respiratory Protective Devices; and
AS/NZS 1716, Respiratory Protective Devices.
Eye Protection Safety glasses with side shields, goggles or full-face shield as appropriate
recommended. Final choice of appropriate eye/face protection will vary
according to individual circumstances i.e. methods of handling or engineering
controls and according to risk assessments undertaken. Eye protection should
conform with Australian/New Zealand Standard AS/NZS 1337 - Eye Protectors
for Industrial Applications.
Hand Cut resistant or leather gloves should be worn when handling strip or sheet
Protection steel, to avoid cuts from splinters, burrs or sharp edges.
Final choice of appropriate gloves will vary according to individual
circumstances i.e. methods of handling or according to risk assessments
undertaken. Reference should be made to AS/NZS 2161.1: Occupational
protective gloves - Selection, use and maintenance.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance Metal hollow section, circular, square, rectangular, flat sided oval or
trapesoidal shapes.
Melting Point 1300掳C (Steel)
Boiling Point 3000掳C
Solubility in
Water Insoluble
Specific
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 5 of 7
Gravity 7.7
Vapour
Pressure 0 torr @ 20掳C
Vapour
Density
(Air=1) Not available.
Flash Point Not applicable.
Flammability Non-combustible
Auto-Ignition
Temperature Not applicable.
Flammable
Limits - Lower Not applicable.
Flammable
Limits - Upper Not applicable.
10. STABILITY AND REACTIVITY
Chemical
Stability Stable under normal conditions of use.
Conditions to
Avoid None known.
Incompatible
Materials None known.
Hazardous
Decomposition
Products None known.
Hazardous
Reactions Not known
Hazardous
Polymerization Will not occur.
11. TOXICOLOGICAL INFORMATION
Inhalation Not expected to be inhaled in the form supplied.
Dust from cleaning & grinding operations, particulate fume, ozone and other
gases from flame cutting and welding may be respiratory irritants.
Ingestion Not expected to be swallowed in the form supplied.
Skin Sharp burrs on the edges of steel products can cause lacerations to
unprotected skin. Burns may result from contact with hot surfaces.
Eye
Not irritating to eyes in the form supplied.
Dust: may cause mechanical irritation. May result in mild abrasion.
Cutting, grinding, hand tool cleaning, etc. operations may generate (hot)
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 6 of 7
metal particles which are potentially injurious to eye tissue.
Chronic Effects Chronic exposure to iron oxide fumes over the standard may lead to Siderosis
which is a benign lung condition.
Chronic exposure to manganese fumes over the standard may lead to
disorders of the nervous and reproductive systems.
12. ECOLOGICAL INFORMATION
Ecotoxicity No data is available for this material.
Persistence /
Degradability No data is available for this material.
Mobility No data is available for this material.
Environment
Protection The material as supplied is not known to be hazardous to the environment.
13. DISPOSAL CONSIDERATIONS
Disposal Dispose of waste according to federal, E.P.A., state and local regulations or
Considerations this material should be undertaken by a registered chemical disposal
company. Assure conformity with all applicable regulations. This product can
be recycled.
14. TRANSPORT INFORMATION
Transport Not classified as a Dangerous Good, according to the Australian Code for the
Information Transport of Dangerous Goods by Road and Rail.
Storage and
Transport Not classified as dangerous goods.
15. REGULATORY INFORMATION
Poisons
Schedule Not Scheduled
16. OTHER INFORMATION
Date of
preparation or
last revision of MSDS review: May 2006
MSDS MSDS superseded: March 2000
Contact
Site Contacts: Newcastle Pipe Mills
Person/Point
Materials Laboratory Technician
(02) 4935 5721
Kembla Grange OIl and Gas Pipe
Process manager
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
MSDS: TUBELINE BLACK, PAINTED, CLEAR COAT AND NOP HOLLOW SEC... Page 7 of 7
(02) 4261 0210
End of MSDS
(C) Copyright ACOHS Pty Ltd
Copyright in the source code of the HTML, PDF, XML, XFO and any other electronic files rendered by an Infosafe system for
Infosafe MSDS displayed on this site is the intellectual property of Acohs Pty Ltd.
Copyright in the layout, presentation and appearance of each Infosafe MSDS displayed on this site is the intellectual property of
Acohs Pty Ltd.
The compilation of MSDS's displayed on this site is the intellectual property of Acohs Pty Ltd.
Copying of any MSDS displayed on this site is permitted for personal use only and otherwise is not permitted. In particular the
MSDS's displayed on this site cannot be copied for the purpose of sale or licence or for inclusion as part of a collection of MSDS
without the express written consent of Acohs Pty Ltd.
http://www.msdsonline.com.au/onesteel/msds/msdsview.asp?SynonymCode=MAD32... 30/03/2007
|