MATERIAL SAFETY DATA SHEET
ATC Panels, Inc.
Product Name: Melamine Laminated Particleboard Page 1 of 8
Date Prepared: June 15, 2006
____________________________________________________________________________________________________________
SECTION 1: Composite Panel Product and Company Identification
Product Identifier: Melamine Laminated Particleboard
General use: Manufacture of kitchen cabinets, store fixture and furniture.
Product Description: A panel product manufactured from cellulosic materials bonded
together with a synthetic resin or other suitable binder, which is covered on one or
both surfaces with a melamine formaldehyde and urea formaldehyde treated paper.
MANUFACTURER: EMERGENCY TELEPHONE NUMBER:
ATC Panels, INC. 919-542-2128
985 Corinth Road
Moncure, North Carolina 27559
SECTION 2: Composition/Information on Ingredients
Wt % CAS Registry #
Ligno-cellulosic Materials 90 - 93 N/A
Polymerized urea formaldehyde resin 7 - 10 9011-05-6
Melamine formaldehyde resin <1 25036-1-9
Kraft paper <1 N/A
OSHA HAZARDOUS COMPONENTS (29 CFR 1910.1200):
EXPOSURE LIMITS
Formaldehyde CAS Registry # 50-00-0 OSHA PEL 鈥? TWA: 0.75 PPM
OSHA PEL 鈥? STEL: 2 PPM
ACGIH TLV 鈥? Ceiling: 0.30 PPM
Melamine/Urea Formaldehdye resin OSHA PEL 鈥? TWA: 0.75 PPM
OSHA PEL 鈥? STEL: 2 PPM
ACGIH TLV 鈥? Ceiling: 0.30 PPM
Wood Dust/Ligno-cellulosic fiber 1, 2 OSHA PEL 鈥? TWA 15.0 mg/m3
(total dust) 5.0 mg/m3 (respirable
fraction)
1
Wood Dust/Ligno-cellulosic fiber 1, 2 ACGIH TLV 鈥? TWA: 1.0 mg/m3
(Softwood) (inhalable dust)
3
ACGIH 鈥? STEL (15 min): 10.0 mg/m
Wood Dust/Ligno-cellulosic fiber 1, 2 ACGIH TLV 鈥? TWA: 1.0 mg/m3
(Certain hardwoods such as beech and oak)
___________________________________________________________
In AFL-CIO v. OSHA 965 F. 2d 962 (11th Cir. 1992), the court overturned OSHA鈥檚 1989 Air
1.
Contaminants Rule, including the specific PELs for wood dust that OSHA had established at that time. The
1989 PELs were: TWA 鈥? 5.0 mg/m3 : STEL (15 min.) 鈥? 10.0 mg/m3 (all soft and hard woods, except
Western red cedar) Western red cedar: TWA 鈥? 2.5 mg/m3.
2. Wood dust is now officially regulated as an organic dust under the Particulates Not Otherwise
Regulated (PNOR) or Inert or Nuisance Dust categories at PELs noted in the Composition/Information on
Ingredients section of this MSDS. However, a number of states have incorporated provisions of the 1989
standard in their state plans. Additionally, OSHA has announced that it may cite companies under the
OSHA General Duty Clause under appropriate circumstances for non-compliance with the 1989 PELs.
SECTION 3: Hazards Identification
EMERGENCY OVERVIEW:
The product may release small quantities of formaldehyde in gaseous form.
Emissions decrease through time as the panels age. Manual or mechanical cutting or
abrasion processes performed on the product can result in generation of wood dust.
POTENTIAL HEALTH EFFECTS:
ACUTE
INHALATION:
Gaseous formaldehyde may cause temporary irritation to nose and throat. Some
reports suggest that formaldehyde may cause respiratory sensitization, such as
asthma, and that pre-existing respiratory disorders may be aggravated by exposure.
Wood dust may cause nasal dryness, irritation and obstruction. Coughing, wheezing,
sneezing, sinusitis and prolonged colds have also been reported.
EYE CONTACT:
Gaseous formaldehyde may cause temporary irritation or a burning sensation. Wood
dust can cause mechanical irritation.
SKIN CONTACT:
Both formaldehyde and various species of wood dust may evoke allergic contact
dermatitis in sensitized individuals.
2
INGESTION:
Not likely to occur.
CHRONIC
International Agency for Research on Cancer (IARC) has listed formaldehyde as a
probable human carcinogen. The National Toxicology Program (NTP) includes
formaldehyde in its Annual Report on carcinogens. OSHA regulates formaldehyde as
a potential cancer agent.
In studies involving rats, formaldehyde has been shown to cause nasal cancer after
long-term exposure to very high concentrations (14+ PPM), far above those normally
found in the workplace.
The National Cancer Institute (NCI) conducted an epidemiological study of industrial
workers exposed to formaldehyde (published June 1986). The NCI concluded that the
data provides little evidence that mortality from cancer is associated with
formaldehyde exposure at the levels experienced by workers in the study.
Wood dust, depending on species, may cause respiratory sensitization and/or
irritation. IARC classifies wood dust as a carcinogen to humans (Group 1). This
classification is based primarily on IARC鈥檚 evaluation of increased risk in the
occurrence of adenocarcinomas of the nasal cavities and paranasal sinuses associated
with exposure to wood dust. IARC did not find sufficient evidence to associate
cancers of the oropharynx, hypopharynx, lung, lymphatic and hematopoietic systems,
stomach, colon or rectum with exposure to wood dust. The NTP includes wood dust
as a known human carcinogen in its Tenth Report on Carcinogens dated November,
2002.
SECTION 4: First Aid Measures
INHALATION:
Remove to fresh air. Get medical attention if irritation persists, severe coughing or
breathing difficulty occurs.
EYE CONTACT:
Flush eyes with large amounts of water. Remove to fresh air. If irritation persists, get
medical attention.
SKIN CONTACT:
Wash affected areas with soap and water. Get medical attention if rash or irritation
persists or dermatitis occurs.
INGESTION:
Not Applicable.
3
SECTION 5: Fire Fighting Measures
FIRE FIGHTING HAZARD:
Wood is classified as a Class A combustible material.
FLASHPOINT AND METHOD:
Not Applicable.
FLAMMABLE LIMITS:
Not Applicable.
AUTOIGNITION TEMPERATURE:
204 鈥? 260 0C (400 鈥? 500 0F)
Ignition of wood takes place when wood is subject to sufficient heat and in
atmospheres that have sufficient oxygen. Ignition can be of two types: piloted or
unpiloted. Piloted ignition occurs in the presence of an ignition source (such as a
spark or flame). Unpiloted ignition is ignition that occurs where no pilot source is
available. The surface temperature of wood materials has been measured somewhere
between 300 0C and 400 0C (572 0F to 752 0F) prior to piloted ignition. Unpiloted
ignition depends on special circumstances that result in different ranges of ignition
temperatures. At this time, it is not possible to give specific ignition data that apply to
a broad range of cases. With convection heating of wood, unpiloted ignition has been
reported as low as 270 0C (518 0F) and as high as 470 0C (878 0F).
FIRE FIGHTING INSTRUCTIONS:
Fire fighting procedures for extinguishing a Class A fire should be followed.
When extinguishing a fire in a wood dust or fiber pile care needs to be taken. A direct
stream of water, into the pile from a hose, could cause the burning material to become
airborne creating a risk in spreading the fire to other areas.
Water is used to quench the burning material below its ignition temperature. The
addition of Class A foams (sometimes referred to as wet water) may enhance water鈥檚
ability to extinguish Class A fires, particularly those that are deep seated in bulk
materials (such as piles of hay bales, sawdust piles, etc.). This is because the Class A
foam agent reduces the water鈥檚 surface tension, allowing it to penetrate more easily
into piles of material. Class A fires are difficult to extinguish using oxygen-exclusion
methods like CO2 flooding or coating with foam because these methods do not
provide the cooling effect needed for total extinguishment.
4
FIRE FIGHTING EQUIPMENT:
Use recommended Class A fire fighting equipment when fighting an incipient fire.
HAZARDOUS COMBUSTION PRODUCTS:
Sawing, sanding or machining can produce wood dust as a by-product that may
present an explosion hazard.
SECTION 6: Accidental Release Measures
LAND SPILL:
Generally not applicable to panel products, however if a spill occurs the applicable
Federal, Provincial, state, and local regulations must be followed.
WATER SPILL:
Generally not applicable to panel products, however if a spill occurs the applicable
Federal, Provincial, state and local regulations must be followed.
SECTION 7: Handling and Storage
STORAGE:
This product should not be stored where exposure to water could occur or near a
source of ignition. Avoid storing in areas of high relative humidity and temperature.
High temperature and inadequate ventilation could allow concentrations of
formaldehyde vapors in the storage area. Adequate ventilation of the storage area will
help reduce the build-up of the formaldehyde vapors. It is recommended to store
product in an area of relative humidity and temperature that approximates end use.
SECTION 8: Exposure Controls/ Personal Protection
ENGINEERING CONTROLS:
Certain activities of the re-manufacturing process of this product could possibly
produce wood dust or formaldehyde vapors. Provide adequate general and local
exhaust ventilation to keep airborne contaminant concentration levels below the
OSHA PELs.
PERSONAL PROTECTION
RESPIRATOR:
Wear NIOSH/MSHA approved respirator when the allowable exposure limits may be
exceeded.
5
PROTECTIVE CLOTHING:
Wear side shield safety glasses during the re-manufacturing of this product. Other
protective equipment such as gloves and outer garments may be needed depending on
dust conditions.
GENERAL HYGIENE:
Practice proper personal hygiene.
SECTION 9: Physical and Chemical Properties
Vapor Pressure: not applicable Vapor Density: not applicable
Specific Gravity: generally < 1 Evaporation Rate: not applicable
Solubility in Water: Insoluble Freezing Point: not applicable
pH: not applicable Odor: Material Dependent
Boiling Point: not applicable Appearance: Material Dependent
Viscosity: not applicable Physical State: Solid
SECTION 10: Stability and Reactivity
STABILITY:
Stable under normal conditions.
REACTIVITY:
Avoid product contact with any temperature sources that could induce thermal
decomposition. Avoid product contact with oxidizing agents and strong acids.
HAZARDOUS DECOMPOSITION:
Thermal and/or thermal-oxidative decomposition can produce irritating and toxic
fumes and gases, including carbon monoxide, hydrogen cyanide, polynuclear
aromatic hydrocarbons, aldehydes and organic acids.
SECTION 11. Toxicological Information
See page 2.
SECTION 12: Ecological Information
No applicable information found.
6
SECTION 13: Disposal Considerations
This panel product is recyclable. It is, however, the user鈥檚 responsibility to determine
at the time of disposal whether your product meets any applicable criteria for
hazardous waste disposal. Disposal must follow applicable Federal, Provincial, state
and local regulations.
SECTION 14: Transport Information
Department of Transportation (DOT): This product is not a DOT hazardous material.
It is the purchaser鈥檚 responsibility to see if this product meets any regulations
depending on their location.
SECTION 15: Regulatory Information
OSHA: Wood products are not hazardous under the criteria of the Federal OSHA
Hazard Communication Standard 29 CFR 1910.1200; however, formaldehyde
emissions from this product and wood dust generated by sawing, sanding or
machining this product may be hazardous.
DOT: This product is not a DOT hazardous material.
TSCA: This product complies with TSCA inventory requirements.
SARA 313: None.
HUD: The Department of Housing and Urban Development (HUD) regulation of 24
CFR 3280 provides for third-party certification of particleboard and interior plywood
manufactured with urea-formaldehyde resin for formaldehyde emissions. The
maximum allowable level for particleboard is 0.3 ppm at a loading ratio of 0.13 ft2/ft3.
Certification is made in accordance with FTM-2-1985 (ASTM E1333-90), Large
Scale Test Method for Determining Formaldehyde Emissions for Wood Products.
California Proposition 65: Warning Statement 鈥? This product contains formaldehyde
(CAS 50-00-0), a chemical known by the State of California to cause cancer.
Minnesota: Minnesota Statute 1984 sections 144.495 and 325F.18 require all
particleboard and plywood sold or used in Minnesota meet the HUD Formaldehyde
Emission Standard, 24 CFR Sections 3280.308 and 3280.406.
7
SECTION 16: Other Information
DEFINITIONS OF ACRONYMS:
ANSI: American National Standards Institute
ACGIH: American Conference of Governmental Industrial Hygienists
ASTM: American Society for Testing and Materials
CAS: Chemical Abstracts Services Registry Number
DOT: Department of Transportation
FTM: Formaldehyde Test Methods
HUD: Department of Housing and Urban Development
IARC: International Agency for Research on Cancer
MSHA: Mining Safety and Health Administration
NIOSH: National Institute for Occupational Safety and Health, U.S. Public Health
Service, U.S. Department of Health and Human Services
NCI: National Cancer Institute
NTP: National Toxicology Program
OSHA: Occupational Safety and Health Administration, U.S. Department of
Labor
PEL: Permissible Exposure Limit
SARA: Superfund Ammendments and Reauthorization Act
STEL: Short Term Exposure Limit
TSCA: Toxic Substances Control Act
TLV: Threshold Limit Value
TWA: Time-weighted Average
WHMIS: Workplace Hazardous Materials Information System
DISCLAIMER
This information was believed to be accurate at the time of preparation, and compiled
from sources believed to be reliable. Products and/or articles manufactured from this
product may have characteristics which are significantly different; therefore, it is the
user鈥檚 responsibility to investigate and understand other pertinent information and to
comply with all applicable laws and regulations. There is no warranty of any kind,
express or implied, concerning product or merchantability or fitness thereof for any
purpose. Buyer assumes all risk of use, storage and handling of the product in
compliance with applicable Federal, State and local laws and regulations. ATC Panels,
Inc. will not be liable for claims relating to any party鈥檚 use of or reliance on information
and data contained herein regardless of whether it is claimed the information and data are
inaccurate, incomplete or otherwise misleading.
8
|