MATERIAL SAFETY DATA SHEET FILE NO.: A
PRODUCT MPT鈩? TWELVE Lubricant and Penetrant (Pump Spray Formula) MSDS DATE: 9/24/2005
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: MPT鈩? Twelve Lubricant and Penetrant Pump Spray Formula
SYNONYMS: Lubricant
Part # MPT-13
MANUFACTURER: MPT鈩? Industries
ADDRESS: 6-B Hamilton Business Park
85 Franklin Road
Dover NJ. 07801
PHONE: 973-989-9220
FAX PHONE: 973-989-9234
CHEMICAL NAME: Mixture
PRODUCT USE: General Purpose Lubricant
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
INGREDIENT: CAS NO. % WT ACGIH-TLV-TWA
Synthetic Hydrocarbon Base Oil 68649-12-7 50-80 None Established
Alkanes, chloro 61788-76-9 04-12 None Established
Dimer Esters 68424-40-8 02-06 None Established
Ditridecyl Adipate 16958-92-2 02-06 None Established
Tritoly Phosphate 1330785 02-04 None Established
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW:
Non-Hazardous under normal conditions of use.
Hot oil can cause thermal burns on contact. Spill may create a slip hazard.
ROUTES OF ENTRY:
Skin contact.
POTENTIAL HEALTH EFFECTS
EYES:
This product can cause mild eye irritation with short-term contact with liquid spray or mist.
SKIN:
This product can cause mild skin irritation with short-term exposure.
INGESTION:
If swallowed in quantities greater than one teaspoon, may cause laxative effect.
INHALATION:
No adverse health effects are expected to occur upon short-term exposure
ACUTE HEALTH HAZARDS:
contains petroleum-based mineral oil. Prolonged or repeated skin contact can cause mild irritation and inflammation characterized
by drying, cracking, or oil acne. inhalation of petroleum-based mineral oil mist above applicable workplace exposure levels can
cause respiratory irritation or other pulmonary effects.
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE:
May aggravate pre-existing skin disorders.
SECTION 4: FIRST AID MEASURES
EYES:
Remove contact lenses if present. Flush eyes with cool, clean low-pressure water while lifting and lowering eyelids.
Seek medical attention if excessive tearing, redness, or pain persists.
SKIN:
Remove contaminated clothing. Wipe off excess material. Wash exposed skin with soap and water. Wash contaminated clothing
before reuse. Leather goods may have to be discarded. If material is injected under the skin seek medical attention immediately
PAGE 1 OF 4
MATERIAL SAFETY DATA SHEET FILE NO.: A
PRODUCT MPT鈩? TWELVE Lubricant and Penetrant (Pump Spray Formula) MSDS DATE: 9/24/2005
INGESTION:
Call poison control. Unless directed by a physician do not induce vomiting or give anything to drink. Seek medical attention
immediately.
INHALATION:
This material is not expected to cause inhalation related disorders under anticipated conditions of use. In case of over-exposure
move the person to fresh air.
SECTION 5: FIRE-FIGHTING MEASURES
FLAMMABLE LIMITS IN AIR, UPPER: No Data
(% BY VOLUME) No Data LOWER: No Data
FLASH POINT:
F: 426.2
C: 219
METHOD USED:
Cleveland open Cup
AUTOIGNITION TEMPERATURE:
343 C
NFPA HAZARD CLASSIFICATION
HEALTH: 0 FLAMMABILITY: 1 REACTIVITY: 0
HMIS HAZARD CLASSIFICATION
HEALTH: 1 FLAMMABILITY: 1 REACTIVITY: 0
PROTECTION: B
EXTINGUISHING MEDIA:
Use dry chemical, foam, carbon dioxide, or water fog
SPECIAL FIRE FIGHTING PROCEDURES:
Firefighter must use full bunker gear, including NIOSH approved positive pressure self-contained breathing apparatus.
UNUSUAL FIRE AND EXPLOSION HAZARDS:
This material can burn, but will not readily ignite. In enclosed spaces heated vapor can ignite with explosive force. Mist or spry may
burn at temperature below flash point.
HAZARDOUS DECOMPOSITION PRODUCTS:
Carbon dioxide, carbon monoxide, unburned hydrocarbons, and traces of sulfur, phosphorus, zinc, and or nitrogen.
SECTION 5 NOTES:
Combustion generates toxic fumes.
SECTION 6: ACCIDENTAL RELEASE MEASURES
ACCIDENTAL RELEASE MEASURES:
Add dry material to absorb spill. Avoid walking through material. Comply with all laws and regulations for waste disposal.
SECTION 7: HANDLING AND STORAGE
HANDLING AND STORAGE:
Avoid container damage. Keep away from excessive heat.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
VENTILATION:
None required under normal operating conditions.
RESPIRATORY PROTECTION:
None required under normal operating conditions.
EYE PROTECTION:
Safety glasses equipped with side shields should be adequate under most condition of use.
PAGE 2 OF 4
MATERIAL SAFETY DATA SHEET FILE NO.: A
PRODUCT MPT鈩? TWELVE Lubricant and Penetrant (Pump Spray Formula) MSDS DATE: 9/24/2005
SKIN PROTECTION:
If prolonged contact is expected, chemical resistant gloves should be used. If product is handled at an elevated temperature, use
heat protective gloves.
WORK HYGIENIC PRACTICES:
Wash hands after using. Remove soiled clothing.
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Translucent Green.
ODOR: Mild petroleum odor.
PHYSICAL STATE: Liquid.
pH AS SUPPLIED:
pH (Other):
BOILING POINT:
F: 777.2
C: 414
MELTING POINT:
F: Not Available
C: Not Available
FREEZING POINT:
F: Not Available
C: Not Available
VAPOR PRESSURE (mmHg):
@ Nil
VAPOR DENSITY (AIR = 1):
@ Not Available
SPECIFIC GRAVITY (H2O = 1):
0.82@ 15.6 C
EVAPORATION RATE:
Not Available
SOLUBILITY IN WATER:
Insoluble in water
SECTION 10: STABILITY AND REACTIVITY
STABLE UNSTABLE
STABILITY: Stable.
CONDITIONS TO AVOID (STABILITY):
Keep away from extreme heat, sparks or open flame and strong oxidizing conditions.
INCOMPATIBILITY (MATERIAL TO AVOID):
Strong acids, Bases and oxidizing agents
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS:
Carbon dioxide, carbon monoxide, unburned hydrocarbons, and traces of sulfur, phosphorus, or nitrogen.
HAZARDOUS POLYMERIZATION:
Not expected to occur.
SECTION 11: TOXICOLOGICAL INFORMATION
TOXICOLOGICAL INFORMATION:
No toxicity testing conducted on this product. Any health or toxicological information included in Sections 3 was based on data
associated with the components. Used in manufacturing this product.
PAGE 3 OF 4
MATERIAL SAFETY DATA SHEET FILE NO.: A
PRODUCT MPT鈩? TWELVE Lubricant and Penetrant (Pump Spray Formula) MSDS DATE: 9/24/2005
SECTION 12: ECOLOGICAL INFORMATION
ECOLOGICAL INFORMATION:
Do not allow to enter soil, waterways, or wastewater
SECTION 13: DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHOD:
It is the responsibility of the individual using this product to follow all local, State and Federal regulation for the proper disposal of
this product and containers.
RCRA HAZARD CLASS:
It is the responsibility of the user to determine if this material is a RCRA Hazardous Waste at the time of disposal.
SECTION 14: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME: Not Regulated
HAZARD CLASS: Not Regulated
ID NUMBER: Not Regulated
PACKING GROUP: Not Regulated
LABEL STATEMENT: Not Regulated
WATER TRANSPORTATION
PROPER SHIPPING NAME: Not Regulated
HAZARD CLASS: Not Regulated
ID NUMBER: Not Regulated
PACKING GROUP: Not Regulated
LABEL STATEMENTS: Not Regulated
AIR TRANSPORTATION
PROPER SHIPPING NAME: Not Regulated
HAZARD CLASS: Not Regulated
ID NUMBER:
PACKING GROUP: Not Regulated
SECTION 15: REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS
TSCA (TOXIC SUBSTANCE CONTROL ACT):
The components of this product are listed
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT):
311/312 HAZARD CATEGORIES: Immediate (Acute) Health Effects: yes
STATE REGULATIONS: NJ right to know Label
SECTION 16: OTHER INFORMATION
DISCLAIMER: Information presented herein has been compiled from source considered to be accurate and dependable to the best
of our knowledge and belief but is not guaranteed to be so. Nothing herein is to be construed as recommending any practice or any
product in violation of any law or regulation. It is the user鈥檚 responsibility to determine the suitability of any material for a specific
purpose and to adopt such safety precautions as necessary. Since conditions of use are not under our control, we must disclaim all
liability with respect to the use and disposal of our products.
PAGE 4 OF 4
|