MATERIAL SAFETY DATA SHEET Acculam鈩? Epoxyglas
Accurate Plastics, Inc.
18 Morris Place
Yonkers, New York 10705-1929
Phone (914) 476-0700
FAX (914) 476-0527
www.acculam.com
Section 1. Chemical Product and Company Identification
Product name Trade Name
NEMA Grades G10, G11, FR4, FR 5
Acculam鈩? Epoxyglas
Manufacturer IN CASE OF EMERGENCY:
Accurate Plastics, Inc.
18 Morris Place Tel: 914-476-0700
Yonkers, NY 10705-1929
Chemtrec:
Date of Preparation: 11/29/07 Replaces: 10/20/04
Preparers Name KJ Soltys
Section 2. Composition, Information on Ingredients
Component Information Exposure Limits
Chemical Name CAS # TLV, TWA ACGIH OSHA PEL, TWA
10 mg/m3 (dust) 15 mg/m3 (total dust)
Fiberglass 65997-17-3
5 mg/m3 (respirable)
Epoxy Resin 25036-25-3 N/A N/A
Dust generated during grinding, cutting, or drilling fiber glass reinforced plastic contains respirable fiber shaped plastic
(organic) particles which has an OSHA PEL of 5 mg/m3 and nonrespirable fibrous glass dust regulated by OSHA as noted
above. Bromine may be an integral part of the polymer matrices of some laminate grades.
N/A = Not Applicable
Section 3. Hazards Identification
Dust generated during machining and grinding operations may cause skin or eye irritation. Fumes from thermal decomposition
or burning may irritate eyes, nose, and throat. Minimize operator exposure to dust and fumes.
Routes of Exposure Symptoms
Inhalation of dust during machining and grinding operations may cause moderate irritation to
Inhalation
mucous membranes and coughing.
Skin Contact with dust may cause moderate irritation.
Eyes Contact with dust may cause moderate eye irritation, itching and redness.
Ingestion Not determined
Cancer OSHA: N/A IARC: N/A NTP: N/A
Dust generated during grinding, cutting, or drilling fiber glass reinforced plastic produces
respirable fiber shaped plastic (organic) particles whose concentration increases proportionally
Chronic
with dust concentration. These particles are not classified as carcinogenic by IARC or NTP.
However, prolonged inhalation of dust can produce lung disease.
Acculam鈩? Epoxyglas -1- Date of Issue: 11/29/2007
MATERIAL SAFETY DATA SHEET Acculam鈩? Epoxyglas
Section 4. First Aid Measures
Immediately wash the eyes with large amounts of water for at least 15 minutes, occasionally
Eyes lifting the lower and upper lids. Get medical attention immediately. Contact lenses should not
be worn when working with this material.
Immediately wash the contaminated skin with soap and water. If redness, itching or a burning
Skin
sensation develops, get medical attention.
Immediately move the exposed person to fresh air. If not breathing give artificial respiration
Inhalation
and get immediate medical attention.
If large quantities have been swallowed, DO NOT INDUCE VOMITING. If victim is
Ingestion
conscious and alert, give 2 - 4 cups of lukewarm water. Get medical attention immediately.
Section 5. Fire Fighting Measures
Flash Point N/D
Flash Pt. <00oF
Flammability Classification OSHA/NFPA Class: Solid
Extinguishing Media Carbon dioxide, water, foam.
Isolate fire area and deny unnecessary entry.
Fire fighters should wear positive-pressure self-contained breathing apparatus
( SCBA) and protective clothing.
Unusual Fire and Explosions Hazards Dust from machining and fabrication operations may be explosive if mixed
with air in critical proportions in the presence of an ignition source.
Heat from fire can generate decomposition products that may cause a health
hazard.
Section 6. Accidental Release Measures
Contain and manage dust during manufacturing. If collected dust is spilled from collection
Small Spills container sweep up spilled material using water spray to suppress the dust. Shovel into
suitable disposal container. Eliminate all ignition sources.
Eliminate all ignition sources. Sweep up spilled material using water spray to suppress
Large Spills dust. Transfer to proper containers for disposal. Persons not wearing protective equipment
should be excluded from the area of spill until cleanup has been completed.
Section 7. Handling & Storage
Store material in a clean, cool, ventilated area away from all sources of ignition. Dust generated during normal manufacturing
operations can represent both a health hazard and a fire hazard. Use dust control equipment at the point of generation in
machining and sawing operations. Wash hands and other exposed areas thoroughly after handling and wash soiled clothing
before reuse.
Section 8. Exposure Controls/Personal Exposure
Minimize dust generating activities. Wear safety goggles with side shield or
Eye Protection
face shield. Contact lenses must not be worn.
Wear gloves to protect against sharp edges and thermal effects when handling
Skin Protection heated material. To prevent repeated or prolonged skin contact, wear
impervious clothing and boots.
If personal exposure cannot be controlled below applicable limits (See
Respiratory Protection Section 2) by area ventilation, wear a properly fitted particulate respirator
approved by NIOSH/MSHA for protection against dust.
General area ventilation is acceptable if the exposure is maintained below
applicable exposure limits. ( See Section 2) Use local exhaust for sawing and
Ventilation
machining operations.
Emergency eye wash fountains and safety showers should be available in the
Other Precautions
immediate vicinity of any potential exposure.
Acculam鈩? Epoxyglas -2- Date of Issue: 11/29/2007
MATERIAL SAFETY DATA SHEET Acculam鈩? Epoxyglas
Section 9. Physical and Chemical Properties
% Volatile Content by Weight <0.05% Specific Gravity (gm/cc) 1.6
Freezing Point (OC)
Melting Point N/A N/A
Vapor Pressure (mm Hg) N/A Solubility in Water Insoluble
Vapor Density (Air=1) N/A Appearance and Odor Yellow to light green solid
Section 10. Stability and Reactivity
Stability Stable
Conditions to Avoid Protect from heat, sparks, flame and possible sources of ignition.
Incompatibility Avoid contact with strong acids and bases
Carbon dioxide, carbon monoxide, bromine and other hazardous gases.
Hazardous Decomposition Products These gases and other volatiles may be generated under normal processing
conditions.
Hazardous Polymerization Will Not Occur!
Section 11. Toxicological Information (see Section 3. for Exposure Symptoms)
Acute Toxicity
Component Tested Oral LD50 (rat) Dermal LD50 (rabbit) Inhalation LC50 4hr (rat)
Glass Fiber (continuous filament) N/D N/D N/D
Section 12. Ecological Information
Not biodegradable.
Section 13 Disposal Considerations
RCRA: This product, if disposed as shipped, is not considered a hazardous waste as specified in 40 CFR 261. Dispose of in
accordance with all applicable federal, state and local regulations. Generation of particulates during machining and
fabricating operations may be subject to Federal and State Air Pollution Control Laws.
Section 14 Transportation Information
This product, if offered for shipment, is not regulated by USDOT 49 CFR Parts 171 - 180: Regulation of Hazardous Materials
Transportation in Commerce.
Shipping Information N/A
Classification N/A
Identification N/A
Packing Group N/A
Label N/A
NOT REGULATED AS HAZMAT
Section 15. Regulatory Information
Regulations Governing Product:
Inventory Status: United States (TSCA) - All ingredients are on the inventory or exempt from listing.
SARA TITLE III
EPCRA 302 EHS Extremely Hazardous Substance Reporting: N/A
EPCRA 311/312 Tier II Chemical Inventory Reporting: N/A
Regulations Governing Ingredients
Chemical Name CAS #/Chemical Category CERCLA RQ SARA TITLE III EPCRA 313 RQ
Acculam鈩? Epoxyglas -3- Date of Issue: 11/29/2007
MATERIAL SAFETY DATA SHEET Acculam鈩? Epoxyglas
Section 16 Other Information
REFERENCES
CRC Press: Handbook of Chemical and Physical Constants by David R. Lide
Merck & Company: The Merck Index
Sigma-Aldrich Company: Aldrich Handbook of Fine Chemicals
Dictionary of Toxicology by Robert Lewis
US Department of Commerce, Center for Disease Control, National Library of Medicine TOXNET
US Department of Transportation, Research and Special Programs Administration: Hazardous Materials Table, Special
Provisions, Hazardous Materials Communications, Emergency Response Information, and Training Requirements
The information contained herein are given in good faith but no guarantee or warranty of any kind, expressed or implied, is
made with respect to the information above.
Accurate Plastics, Inc. expressly disclaims any liability which may be incurred in using the information contained herein.
Acculam鈩? Epoxyglas -4- Date of Issue: 11/29/2007
|