MATERIAL SAFETY DATA SHEET
HDIS-1
Heavy-Duty Industrial
Heat Transfer Fluid Add Pak
Additives Inc.
5915 N. Broadway
Denver, CO 80216 MSDS No: 5020 EMERGENCY NUMBERS:
Tel: 303-292-0595 Fax: 303-292-0429 Ver. No: 3 PERS 800-633-8253
msds@additivesinc.com Ver. Date: 2/12/02 CUSTOMER SERVICE:
MSDS on-line: www.additivesinc.com 303-292-0595
SECTION 1 - IDENTIFICATION
HDIS-1
Product Name:
Heavy-Duty Industrial Heat Transfer Fluid Additive Package
Product Description:
Mixture
Chemical Name:
Alkaline aqueous solution of inorganic and organic corrosion inhibitors.
Chemical Family:
Mixture
Formula:
Inhibitor package for automotive antifreeze or additive package for automotive
Synonyms:
antifreeze/coolant.
Mixture
CAS Registry:
Mixture
DOT Identification No.:
Corrosive Liquid, Toxic, Class 8, Packing Group II
DOT Hazardous Class:
Corrosive Liquid, Toxic, n.o.s. (Contains: Potassium hydroxide, Sodium nitrite)
DOT Shipping Name:
3093
UN Number:
SECTION 2 - TYPICAL COMPOSITION
MATERIAL CAS NO % WT OSHA PEL
1mg/m3
Tetrapotassium pyrophosphate 7320-34-5 45-55%
Sodium nitrite 7632-00-0 15-20% None established
1mg/m3
Sodium tetraborate pentahydrate 1330-43-3 3-5%
Sodium tolytriazole 64665-57-2 1-3% None established
2mg/m3
Potassium hydroxide 1310-58-3 0-5%
Proprietary inhibitors Not applicable 2-4% Not applicable
Deionized water 7732-18-5 balance Not applicable
SECTION 3 - HMIS RATINGS
1 NFPA
Health:
0
Flammability:
1
Reactivity:
0
0
Special:
1 1
0
0 = minimal 1= slight 2=moderate 3= serious 4= severe
漏2001 Additives Inc. MSDS: HDIS-1
- - - FOR DISCLAIMER OF LIABILITY SEE FINAL PAGE - - - Page 1 of 3
SECTION 4 鈥? PHYSICAL DATA
Somewhat cloudy straw-colored liquid, slightly bitter, caustic odor.
Appearance and odor:
Boiling Point (760 mm Hg): 255掳F
1.28-1.45
Specific Gravity (water =1):
>1.0
Vapor Density (air =1):
NIL
Percent Volatile by Volume:
<1
Evaporation Rate (butyl acetate =1):
100%
Solubility in Water (% by wt):
10mm Hg
Vapor Pressure (at 20掳C):
11.5-12.5
pH:
SECTION 5 鈥? HEALTH HAZARD DATA
Not applicable
TLV and source:
This solution of antifreeze inhibitors is an alkaline irritant and corrosive with a
Effects of overexposure:
pH of 10-12. Prolonged contact can be destructive to tissue. Contact with
the eyes may damage delicate eye tissue. Ingestion will cause mouth, throat
and gastrointestinal irritation. Sodium nitrite can cause cyanosis, headache,
dizziness, nausea and methemoglobinemia. Inhalation of harmful levels of
vapors is unlikely due to the relatively low vapor pressure and the relatively
low concentrations of ingredients.
Flush eyes with large amounts of water for 15 minutes. If
Emergency and First Aid Procedures: Eye contact:
irritation persists, get medical attention.
Wash affected area thoroughly with soap and water.
Skin contact:
Remove contaminated clothing, rings, etc.
Toxic if swallowed. Induce vomiting immediately and seek
Ingestion:
medical attention.
Remove to fresh air. If breathing has stopped, start
Inhalation:
artificial respiration. Seek medical attention.
SECTION 6 鈥? FIRE AND EXPLOSION HAZARD DATA
Not applicable
Flash Point:
Not applicable
Autoignition Temperature:
Not applicable
Flammable limits in air (% by volume):
Extinguishing media: Water, fog, foam, CO2 , dry chemical
Full protective equipment including self-contained breathing apparatus should
Special Fire Fighting procedures:
be used when Additive Inc. Antifreeze Additive Solution is present during a
fire. During emergency conditions, overexposure to decomposition products
may cause a health hazard. Symptoms may not be immediately apparent.
Seek medical attention.
Closed containers may rupture or explode due to steam pressure build-up
Unusual Fire and Explosion Hazards:
when exposed to extreme heat. Water may be used to cool closed
containers.
漏2001 Additives Inc. MSDS: HDIS-1
- - - FOR DISCLAIMER OF LIABILITY SEE FINAL PAGE - - - Page 2 of 3
SECTION 7 鈥? REACTIVITY DATA
Stable
Stability:
Strong oxidizing agents, strong acids.
Incompatibility:
If involved in a fire the following decomposition products may be generated:
Hazardous decomposition products:
Carbon dioxide, carbon monoxide, nitrogen oxides, hydrogen cyanide (possible
in reducing atmospheres).
Will not occur.
Hazardous polymerization:
SECTION 8 鈥? SPILL OR LEAK PROCEDURES
For small spills, soak up with suitable absorbent material. For large spills, dike
Steps to be taken if material is
and pump into suitable containers. Clean up residual water.
released or spilled:
Sanitary landfill or incinerate in approved facilities in accordance with local,
Waste disposal method:
state and federal regulations.
SECTION 9 鈥? PERSONAL PROTECTION INFORMATION
If personal exposure cannot be controlled below applicable exposure limits by
Respiratory protection:
ventilation, wear respiratory devices approved by NIOSH/MSHA, for protection
against organic vapors, dust, fumes and mists.
Local exhaust is recommended.
Ventilation:
Where skin contact may occur, chemical-impervious gloves should be worn.
Protective gloves:
Use chemical goggles or full face shield when the danger of splashing exists
Eye protection:
Rubber apron or similar protective clothing to prevent contact with skin or
Other protective equipment:
clothes.
SECTION 10 鈥? ADDITIONAL PRECAUTIONS
Avoid contact with skin, eyes and clothing. Do not take internally. Clean up
Alkaline irritant:
spills immediately.
Keep containers tightly closed when not in use. Store only in containers that
Precautions to be taken in handling
are resistant to alkaline solutions with a pH of 12-14.
and storage:
SECTION 11 鈥? GENERAL COMMENTS
THE INFORMATION GIVEN HEREIN IS GIVEN IN GOOD FAITH AND FROM SOURCES WE BELIEVE RELIABLE.
BUT NO WARRANTY, EXPRESS OR IMPLIED, REGARDING ITS CORRECTNESS IS MADE.
The conditions or methods of handling, storage, use and disposal of this product are beyond our control and may be
beyond our knowledge. For this and other reasons, we do not assume responsibility and expressly disclaim liability for
loss, damage or expense arising out of or in any way connected with the handling, storage, use or disposal of this
product.
This MSDS was prepared and is to be used only for this product. If the product is used as a component in another
product, this MSDS information may not apply.
CONSULT ADDITIVES INC. FOR FURTHER INFORMATION.
漏2001 Additives Inc. MSDS: HDIS-1
- - - FOR DISCLAIMER OF LIABILITY SEE FINAL PAGE - - - Page 3 of 3
|