MATERIAL SAFETY DATA SHEET
Prepared according to 29 CFR 1910.1200
N/A = Not applicable Revised 1/15/03
SECTION 1 - PRODUCT IDENTIFICATION Inhalation: Inhalation-spray mists may cause mild respiratory
irritation.
Eye Contact: Liquid splashed into the eye may cause transient eye
Trade Name: Safecoat Cabinet &Trim Enamel - SemiGloss
irritation.
Product I.D.# & Color: 1052 White
Skin Absorption: None known.
Product Class: Waterborne Polymer Emulsion
Symptoms and Effects of Repeated Overexposure: Chronic - None known.
Supplier's Name: American Formulating & Manufacturing
Medical Conditions Generally Aggravated by Exposure: None known.
Telephone #: (619) 239-0321 Fax # 619-239-0565
Emergency & First Aid Procedures:
Address: 3251 Third Avenue, San Diego, CA 92103
Emergency Phone (MSDS Information): (619) 239-0321 or (562) 693-0872 Inhalation: Remove from exposure. Provide plenty of fresh air.
D.O.T. Emergency Phone Number: (562) 693-0872 Splash (eyes): Flush immediately with large amounts of water for at least 15
US DOT Hazard Shipping Class: Not regulated - aqueous minutes, lifting upper and lower eyelids occasionally. Take to a physician for
D.O.T. Labels/Placards Required: No medical treatment.
OSHA Class: 29CFR 1910.1200 Non-hazardous Splash (skin): Remove with soap and water. Remove contaminated clothing.
SARA TITLE III Emergency & Community Right to Know: Supply copious amounts of fresh water to the skin areas to rinse material away.
Section 311/312 Categorizations (40 CFR 370): Not a hazardous chemical Ingestion (Swallowing): Consult with physician, hospital emergency room, or
Section 313 Information (40 CFR 372): This product does not contain a chemical poison control center immediately. Only if conscious, give 2 glasses of water to
which is listed in Section 313 above de minimis concentrations. drink.
Notes to Physician: Any treatment that might be required for overexposure
should be directed at the control of symptoms and the clinical conditions.
SECTION 2 - INGREDIENTS
SECTION 6 - REACTIVITY DATA
Acrylic Emulsion Copolymer CAS #: Mixture Weight Percent: 45 鈥?
50
Stability: Stable, however avoid temperatures above 177掳C/350掳F, the onset of
Vapor Pressure 17 mm Hg @ 68 F
Titanium Dioxide CAS #: 13463-67-7 Weight Percent: 15 鈥? polymer decomposition.
20 Incompatibility (materials to avoid): Avoid materials that are water reactive,
Pigment dust when dry or sanded ACGIH TLV 10 mg/m3 total dust highly alkaline or highly acidic.
Acrylic Emulsion Copolymer CAS #: Mixture Weight Percent: 10 鈥? Hazardous Decomposition by-products: CO, CO2 on combustion
15 Hazardous Polymerization: Will not occur.
Vapor Pressure 17 mm Hg @ 68 F Conditions to Avoid: Excess heat may cause containers to rupture. Avoid
Water CAS #: 7732-18-5 Weight Percent: 10 鈥? temperatures below 45掳F or freezing conditions.
15
Aqueous Copolymer CAS #: Mixture Weight Percent: < 4 SECTION 7 - SPILL, DISPOSAL PROCEDURES; ENVIRONMENTAL DATA
Vapor Pressure 14 mm Hg @ 68 F
Ester Alcohol CAS #: 25265-77-4.010 Weight Steps to be taken in case material is released or spilled: Confine in small
Percent: < 3 area; contain and remove with inert absorbent (sand, earth, etc.). Place in proper
Acrylic Emulsion Copolymer CAS #: Mixture Weight Percent: < 3 container for proper disposal. CAUTION - Keep out of waterways, drains, sewers
Vapor Pressure 17 mm Hg @ 68 F by diking. Keep spectators away. Floor may be slippery. Use care to avoid
Propylene Glycol CAS #: 57-55-6 Weight Percent: < 3 falling.
Vapor Pressure .22 mm Hg @ 77 F Waste Disposal Method: Place contaminated material in suitable sealed metal
Suspected Cancer Agents: Federal OSHA: No NTP: NO IARC: No None containers for disposal. Do not incinerate closed containers. Use non leaking
known. containers, seal tightly and label properly. Do not pour contaminated paint back
HMIS Codes: H-1 F-0 R-0 P-B into unused paint. Do not throw liquid paint into the trash. Where allowed by
local laws (check with local regulatory agencies) allow liquid waste materials to
SECTION 3 - PHYSICAL DATA dry out before disposing into trash containers. Take all liquid unused paint that
Physical Description: Viscous liquid, low odor, mildly alkaline, white (if not cannot be used to approved recycling centers, paint roundups, or county facilities
tinted). Very mild paint odor. that are approved to take unused paint at collection sites. Contact state, county,
Boiling Point: ........................................................................100 C/212 F city health services or fire departments to find nearest collection centers. Do not
Melting Point: .......................................................................N/A dispose of waste into water streams or storm water sewers. Do not mix with
Vapor Density:......................................................................Heavier than air other kinds of waste. Dispose all waste in accordance with local, state and
% Volatile by Volume: ..........................................................63.36% federal regulations.
LBS/GAL Theoretical: ..........................................................10.05 +or- .15 RCRA Classification: As produced, this product is not a waste. If discarded as
Solubility in Water: ...............................................................Dilutable is, it is not classified a 鈥淗azardous鈥? waste under RCRA. This product is not
Vapor Pressure, mmHg @ 20degC: ....................................N/A ignitable, corrosive, reactive, or toxic; therefore is not defined as hazardous by the
Evaporation Rate:.................................................................Slower than ether EPA.
% Volatile by Weight:...........................................................53.00% Environmental Hazards: None known.
Specific Gravity (Water=1):..................................................1.21
VOC Material:.......................................................................63 g/l, 0.53 lb./gal SECTION 8 - SPECIAL PROTECTION INFORMATION
VOC Material less H20: ......................................................147 g/l, 1.23 lb./gal
Respiratory Protection: If applied by spraying, use an appropriate, properly
SECTION 4 - FIRE & EXPLOSION HAZARD DATA fitted NIOSH/MSHA approved respirator to remove spray mist. Good room
(mechanical) ventilation should be sufficient protection against vapors from
Flash Point: N/A non-combustible product. If further protection is desired or if persons are sensitive to vapors, use
Flammable limits in air, volume % - lower LEL: .62 Upper UEL: 12.5 a respirator with a NIOSH/MSHA approval number TC-23C-860 or TC-23C-87 or
Fire Extinguishing Media: Water, carbon dioxide, dry chemical an equivalent. Refer to OSHA 29 CFR 1910.134, 鈥淩espiratory Protection鈥?.
Personal Protective Equipment: Self-contained breathing apparatus (pressure- Ventilation: General (mechanical) room ventilation is expected to be
demand MSHA/NIOSH approved or equivalent) and full protective gear may be satisfactory.
worn if desired, but not necessary for normal use. Protective Gloves: None required under most conditions. If protection is
Autoignition Temp.: N/A desired, plastic, nitrile or latex rubber will provide adequate protection.
Special Fire Fighting Procedures: Use water (fog) to cool closed containers. Eye Protection: Safety glasses or goggles with side shields if splashing may
Wear self contained breathing apparatus. occur. Use goggles when spraying, ANSI Z87.1 or approved equivalent.
Unusual Fire & Explosion Hazards: Closed containers may explode due to the Other Protection: Eye wash or copious amounts of water as a precautionary
build up of steam pressure when exposed to extreme heat. Material can splatter measure is suggested. Other equipment not likely to be needed.
above 100掳C/212掳F. Polymer film can burn.
SECTION 9 - STORAGE & SPECIAL HANDLING
SECTION 5 - HEALTH HAZARD INFORMATION & FIRST AID
Storage Temperature: Min. 45degF - Max. 120degF/Indoor and outdoor = OK
Threshold Limit Value: See Section 2 for hazardous ingredient information This product should be stored at room temperature to prolong shelf life. Keep
Symptoms of Overexposure containers in a cool, dry place. Avoid subjecting this product to extreme
Symptoms and Effects of Short Term Exposure: Acute. Primary route of temperature variations and freezing. Adverse conditions can cause emulsion
entry: coagulation.
Swallowing: Unknown.
KEEP CONTAINER CLOSED. KEEP OUT OF REACH OF CHILDREN. DO
NOT TAKE INTERNALLY. DO NOT GET IN EYES. IF PRODUCT IS
SPRAYED, PREVENT PROLONGED OR REPEATED BREATHING OF SPRAY
MIST. USE ADEQUATE VENTILATION WHEN USING THIS PRODUCT. USE
GOOD HYGIENE PRACTICES AND WASH AFTER USING PRODUCT.
NOTICE: The data and recommendations presented herein are based upon our
research and the research of others, and are believed to be accurate. No
guarantee of their accuracy is made, however, and the product discussed is
distributed without warranty, expressed or implied, and the person receiving such
product shall make his own determination of the suitability thereof for his
particular purpose. The use of this information and the conditions and use of this
product are controlled by the user, and it is the responsibility and obligation of the
user to determine the conditions of safe use of this product. If persons using this
product are chemically sensitive, a test for personal tolerance is recommended.
|