MATERIAL SAFETY DATA SHEET
MSDS # 1216 - ROOFING ASPHALT AND EASY-MELT 200
IMPORTANT:Read this MSDS before handling or disposing of this product. This product safety information is
provided to help our customers assess compliance with health, safety and/or environmental regulations. We have
taken reasonable effort to ensure that the test methods and sources for this data are correct and reliable, however,
we give no warranty, expressed or implied, regarding its correctness. Since conditions or methods of handling and
using this product are beyond our control, we do not assume responsibility and expressly disclaim liability for
damages resulting from or connected with the handling, storage, use or disposal of the product.
SECTION 1 PRODUCT AND MANUFACTURER鈥橲 INFORMATION
Manufacturer鈥檚 Name: IKO Industries Ltd.
Address: 71 Orenda Road,
Brampton, Ontario
L6W 1V8
Emergency Phone: (905) 457-2880 - EXT. 4402
Product Name: Roofing Asphalt and Easy-Melt 200
Chemical Name: Asphalt (Petroleum)
Trade Name: B.U.R. Asphalt, Type I, Type II, Type III; coating, saturant, I0 PEN, 95/25
Chemical Family: Petroleum Hydrocarbons
SECTION 2 PREPARATION INFORMATION
Prepared By: Andy Lodge
Phone Number: (905) 457-2880 - EXT. 4402
Date of Preparation: November 1, 2005
SECTION 3 HAZARDOUS INGREDIENTS
Component TLV-TWA (8H) %(vol) CAS #
0.5 mg/m3 (benzene soluble fraction of the inhalable particulate)*
Bitumens > 97 64742-93-4
14 mg/m3
Sulphur <3 7704-34-9
Note: During storage or transit of hot asphalt, small amounts of toxic hydrogen sulphide (CAS #7783-06-4) may be
generated.
* ACGIH has recommended that the TLV-TWA for asphalt fumes be reduced to 0.5 mg/m3 from 5.0 mg/m3. There is
no documentation that supports this reduction as the method of measuring has changed as well as the value. The
NIOSH REL remains at 5.0 mg/m3. There is no PEL for asphalt fumes listed by OSHA.
SECTION 4 PHYSICAL DATA
Boiling Point: >470掳C (> 878掳F)
Specific Gravity: 1.1 g/cc at 15掳C (approximate)
Vapour Pressure: NIL @ 38掳C
Evaporation Rate: Not applicable
Solubility In Water: Insoluble
Appearance: Black plastic semi-solid when cold, viscous fluid when hot
Odour: Characteristic asphalt odour
SECTION 5 FIRE AND EXPLOSION DATA
Auto-Ignition Temperature: 370 - 480掳C ( 698掳 - 867掳F) (approx.)
Flash Point: 274掳C (525掳F) minimum by C.O.C.
Flammable Limits: Not known
Extinguishing Media: Dry chemical, carbon dioxide; water may be used to cool fire, but can cause
frothing.
Special Procedures: Respirators required for fire fighting. Cool tanks exposed to fire with water.
Excessive use of water may spread the fire.
Unusual Fire Hazards: Slightly combustible. When heated above its flash point or if held in storage at
high temperatures, this material can release flammable vapours which can burn
in the open or be explosive in confined spaces if exposed to ignition.
IKO BRAMPTON 1 OF 2 NOVEMBER 2005
MATERIAL SAFETY DATA SHEET
MSDS # 1216 - ROOFING ASPHALT AND EASY-MELT 200
SECTION 6 TOXICOLOGICAL PROPERTIES
Toxicity Data: IARC states that there is inadequate evidence that bitumens alone are
carcinogenic to humans.
Effects of Overexposure:
Inhalation: Fumes from hot asphalt may cause nausea, headache or dizziness
Skin and Eyes: Hot asphalt burns skin and eyes. Prolonged or repeated skin contact may cause
dermatitis.
Ingestion: Ingestion is unlikely.
SECTION 7 REACTIVITY DATA
Conditions to Avoid: Excessive heat approaching flash point
Stability: Stable
Polymerization: Will not occur
Materials to Avoid: Strong oxidizers, strong acids, alkalis
Hazardous
Decomposition
Products: COx, SOx, NOx, smoke on combustion, hydrogen sulphide (storage of hot
product).
SECTION 8 PREVENTATIVE MEASURES
Spill Procedure: In case of spill or leakage, allow to harden and shovel into container.
Disposal Procedure: Follow federal, provincial/state, and local laws and regulations.
Ventilation: Ventilate as needed in confined areas so as to comply with exposure limits.
(0.5 mg/m3 - asphalt fumes, 10 ppm - hydrogen sulphide)
Respiratory: When needed, use only NIOSH certified respiratory protection.
Gloves: Minimize skin contact. Use protective gloves when handling material.
Eye Protection: Use splash proof chemicals goggles.
Other: If contact is unavoidable, wear a face shield, long-sleeved sheet, cuffless pants,
loose clothing.
SECTION 9 FIRST AID PROCEDURES
Skin: For hot asphalt contact, cool body part by water immersion or shower. DO NOT
attempt removal of asphalt, but split longitudinally if splash is circumferential to
avoid tourniquet effect. For skin soiling without underlying burn, cleanse with
mineral oil followed by soap and water. Use olive oil in vicinity of the eyes.
Eyes: Copious warm water flush (minimum 15 min.). Get a physicians assessment if
eyes are inflamed. Cleanse soiling with a vegetable oil (such as olive oil).
Inhalation: Evacuate to fresh air. Apply Cardio Pulmonary Resuscitation if required.
Physician assessment mandatory.
Ingestion: N/A
Notes to Physician: No attempt should be made to remove firmly adhering bitumen from the skin. Once bitumen is
cool, it does no further harm and provides a sterile covering over burnt area. Bitumen plaque
will detach itself as healing progresses. If solvent treatment is used, it should be followed by
washing with soap and water, then application of refatting agent or skin cleansing cream. Only
medically approved solvents may be used to remove bitumen from burns, as other solvents
may cause further skin damage.
SECTION 10 OTHER
Store and transport this material at a temperature as far below its flash point as possible. Use in well ventilated
areas; avoid breathing vapours. For outdoor use, remain upwind of hot asphalt when possible. Avoid skin and eye
contact. During storage or transit of hot asphalt, hydrogen sulphide may accumulate in enclosed spaces. Open tank
car hatches with caution. Avoid inhalation. Maintain same precautions when gauging and sampling.
IKO BRAMPTON 2 OF 2 NOVEMBER 2005
|