MATERIAL SAFETY DATA SHEET
MANUFACTURER: LIFE AUTOMOTIVE PRODUCTS, INC. No.: 1 OF 6
1210 MIDAS COVE STE 101
CORDOVA, TN 38018
EMERGENCY CONTACT: CHEMTREC
EMERGENCY PHONE NUMBER: 800-424-9300
PRODUCT NAME: MIGHTY TOTAL INTAKE CLEANER
PRODUCT CODE No.: SB300 ISSUE DATE: 01/01/05
HMIS HAZARD INDEX: HMIS RATINGS:
HAZARDOUS 4-SEVERE HEALTH 2
MATERIALS 3-SERIOUS FLAMMABILITY 3
IDENTIFICATION 2-MODERATE REACTIVITY 0
SYSTEM 1-SLIGHT PERSONAL PROTECTION*
0-MINIMAL *SEE SECTION VII
NFPA HAZARD RATINGS:
4-EXTREME
3-HIGH
2-MODERATE
1-SLIGHT
0-INSIGNIFICANT
SECTION I
COMPONENTS PRODUCT IDENTIFICATION
CAS No. TLV OSHA %
COMPLEX BLEND OF:
HETEROCYCLIC AMINES AZEOTROPED WITH
PRIMARY ALKYL AMINE, ACETRONILRILE, AND
DEIONIZED WATER. (N/A) 40 ppm 100% A.I.
DIMETHYL ETHER (DME) 115-10-6 1000ppm (DuPont) 70/30
SECTION II
PHYSICAL PROPERTIES
BOILING POINT VAPOR DENSITY (AIR+1) % VOLATILE ODOR
WIDE RANGE > 3.0 100 AMMONIACAL
% SOL. IN WATER SPECIFIC GRAVITY Ph RANGE APPEARANCE
100% conc. 0.963 Conc. 12.2 TO 12.8 STRAW ?YELLOW
EVAPORATION RATE (N BUTYL ACETATE=1) VAPOR PRESSURE (mm Hg OR PSIG)
N/A AEROSOL ?60 PSIG @ 70 Deg. F.
PRODUCT NAME: MIGHTY TOTAL INTAKE CLEANER PAGE No.: 2 OF 6
PRODUCT CODE No. SB300 ISSUE DATE: 01/01/05
SECTION III
FIRE AND EXPLOSION DATA
FLASHPOINT (METHOD USED): FLAMABLE LIMITS:
-41 C TOC (DME) 3.4 L.E.L. 18.0 U.E.L.
SPECIAL FIRE FIGHTING PROCEDURES:
EVACUATE ALL PERSONNEL FROM DANGER AREA. COOL SURROUNDING AREA WITH
WATER SPRAY. WEAR SELF-CONTAINED BREATHING APPARATUS. WEAR FULL
PROTECTIVE EQUIPMENT. EXPLODING AEROSOL UNITS, CAN BECOME DANGEROUS
MISSILES.
UNUSUAL FIRE AND EXPLOSION HAZARD:
FIRE FIGHTERS SHOULD WEAR SPECIAL PROTECTIVE EQUIPMENT AND WEAR A SELF-
CONTAINED BREATHING APPARATUS. SMOKE OF UNBURNED MATERIALS CAN
CONTAIN OXIDES OF NITROGEN.
EXTINGUISHING AGENTS:
WATER SPRAY, CARBON DIOXIDE, DRY CHEMICAL OR FOAM.
SECTION IV
ROUTES OF ENTRY: INHALATION ( X ) SKIN ( X ) EYES ( X ) INGESTION ( X )
INHALATION:
OVER EXPOSURE BY INHALATION MAY CAUSE CHEST TIGHTNESS OR PAIN, NAUSEA,
VOMITING, FLUSHING CONFUSION, DROWSINESS, UNCONSCIOUS, CONVULSIONS
AND GROSS OVER EXPOSURE MAY CAUSE DEATH.
SKIN CONTACT:
MAY CAUSE BURNING, IRRITATION, REDNESS AND SWELLING.
EYE CONTACT:
EYE IRRITANT AND CAUSES TEARING, BLURRING OF VISION AND PAIN.
INGESTION:
RESPIRATORY TRACT (TRACHEA AND ESOPHAGUS) IRRITANT WITH THE SAME
SYMPTOMS AS OVER EXPOSURE OR BREATHING.
PRODUCT NAME: MIGHTY TOTAL INTAKE CLEANER PAGE No.: 3 OF 6
PRODUCT CODE No. SB300 ISSUE DATE: 01/01/05
SECTION V
EMERGENCY AND FIRST AID PROCEDURES
INHALATION:
IMMEDIATELY REMOVE TO FRESH AIR. IF NOT BREATHING, GIVE ARTIFICIAL
RESPIRATION. IF BREATHING IS DIFFICULT, GIVE OXYGEN. CALL A PHYSICAN.
SKIN CONTACT:
IMMEDIATELY FLUSH WITH PLENTY OF WATER. REMOVE CONTAMINATED
CLOTHING AND WASH. GET MEDICAL ATTENTION IF NEEDED.
EYE CONTACT:
IMMEDIATELY FLUSH WITH PLENTY OF WATER FOR AT LEAST 15 MINUTES. CALL A
PHYSICIAN.
INGESTION:
IMMEDIATELY GIVE TWO (2) GLASSES OF WATER AND INDUCE VOMITING. DO NOT
GIVE SYRUP OF IPECAC. NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS
PERSON. CALL A PHYSICIAN.
COMMENTS:
SEE CAUTION UNDER VENTILATION.
SECTION VI:
REACTIVITY DATA
STABILITY: STABLE ( X ) UNSTABLE ( )
MATERIALS TO AVOID:
OXYGEN, OXIDIZERS, ACIDS, CARBON DIOXIDE, AND UV.
HAZARDOUS POLYMERIZATION: MAY OCCUR ( ) WILL NOT OCCUR ( X )
HAZARDOUS DECOMPOSITION PRODUCTS:
CARBON DIOXIDE, CARBON MONOXIDE, AMMONIA, NITROGEN OXIDES.
CONDITIONS TO AVOID:
HIGH TEMPERATURES, SPARKS AND OPEN FLAME. AUTOIGNITION AT 350
Deg. C. AEROSOL CONTAINERS MAY RUPTURE ABOVE 150 Deg. F.
PRODUCT NAME: MIGHTY TOTAL INTAKE CLEANER PAGE No.: 4 OF 6
PRODUCT CODE No. SB300 ISSUE DATE: 01/01/05
SECTION VII
SPECIAL PROTECTION INFORMATION
VENTILATION: "CAUTION EXHAUST HAZARD"
TESTS SHOW THAT A SERIES OF TOXIC CHEMICALS FORM, FROM UNBURNED FUELS,
ADDITIVES, AND ENGINE FOG AND ARE FOUND IN THE EXHAUST DURING THE
PRODUCT NAME: INTAKE UPPER ENGINE CLEANER PAGE No.: 4 OF 6
PRODUCT CODE No.: 17020 ISSUE DATE: 01/01/05
ENGINE ?RUNNING CHEMICAL CLEANING PROCEDURE. MAKE SURE THE EMISSION
VAPORS ARE EXHAUSTED OUTSIDE THE WORK PLACE AND THE WIND IS NOT
CARRYING VAPORS TOWARD ANY PEOPLE. VAPORS CONTAIN HIGH LEVELS OF
NITROGEN OXIDES.
RESPIRATORY PROTECTION:
IF VENTILATION PRECAUTIONS ARE NOT POSSIBLE, THEN USE A NIOH/MSHA
APPROVED RESPIRATOR FOR THE REMOVAL OF AMMONIA, NITROGEN OXIDES,
CARBON MONOXIDE, AND CARBON DIOXIDE.
PROTECTIVE GLOVES:
WEAR THIN LATEX GLOVES. USE CARE WHEN USING.
EYE PROTECTION:
WEAR CHEMICAL SPLASH GOGGLES.
OTHER PROTECTIVE EQUIPMENT:
WIPE SHIN DRY WITH CLEAN SHOP TOWEL AND WASH WITH WATER BEFORE EATING
OR LEAVING WORK AREA.
SECTION VIII
SPILL AND LEAK PROCEDURES
PRECAUTIONS IN CASE OF A LEAK OR SPILL:
REMOVE SOURCE OF SPARKS OR FLAME. EVACUATE PERSONNEL. DIKE SPILL.
THOROUGHLY VENTILATE AREA. USE SELF-CONTAINED BREATHING APPARATUS
DURING CLEAN UP. REMOVE FREE LIQUID FOR RE-USE OR RECLAMATION.
PRECAUTIONS IN CASE OF A LEAK OR SPILL:
REMOVE SOURCE OF SPARKS OR FLAME. EVACUATE PERSONNEL. DIKE SPILL.
THOROUGHLY VENTILATE AREA. USE SELF-CONTAINED BREATHING APPARATUS
DURING CLEAN UP. REMOVE FREE LIQUID FOR RE-USE OR RECLAMATION.
WASTE DISPOSAL METHOD:
PRODUCT IS VERY WATER SOLUBLE AND NOT SUITABLE TO DISPOSE IN WASTE OIL.
WHEN DELUTED WITH HIGH VOLUMES OF WATER THE PRODUCT IS NONTOXIC.
HOWEVER, DISPOSE IN ACCORDANCE WITH FEDERAL, STATE, AND LOCAL
REGULATIONS.
PRODUCT NAME: MIGHTY TOTAL INTAKE CLEANER PAGE No.: 5 OF 6
PRODUCT CODE No. SB300 ISSUE DATE: 01/01/05
SECTION IX
STORAGE AND SPECIAL PRECAUTIONS
HANDLING AND STORAGE PRECAUTIONS:
STORE IN A VENTILATED AREA. STORE AWAY FROM SPARKS AND FLAME. DO NOT
STORE ABOVE 120 Deg. F.
OTHER PRECAUTIONS:
KEEP OUT OF REACH OF CHILDREN. NO SMOKING OR EATING IN HANDLING OR USE
AREA. INHALING PARTIALLY OXIDIZED VAPORS THROUGH CIGARETTES COULD BE
LETHAL.
NOTES TO PHYSICIAN FOR SYMPTOMATIC TREATMENT:
PHYSICIANS TREAT SYMPTOMS OBSERVED.
SECTION X
TRANSPORTATION INFORMATION
Hazard Class: ORM-D SUB CLASS III
UN/NA Code:
Packing Group:
Bill of Lading Description:
Labels Required:
Placards Required:
SECTION XI
REGULATORY INFORMATION
Listed below are the hazard categories for SARA Section 311/312 (40 CFR 370):
Immediate Hazard: - Delayed Hazard: - Fire Hazard: -
Pressure Hazard: - Reactivity Hazard: -
Reporting Requirements of SARA Section 313 (40 CFR 372): The reportable quantity for this
material is 5,000 pounds. Any spill or other release, or substantial treat of release, of this material
to air, water, or land (unless entirely contained in the workplace) equal to or in excess of the
reportable quantity must be reported immediately to the National Response Center (800- 424-
8802) as required by U.S. Federal Law. Also contact appropriate state and local regulatory
agencies.
PRODUCT NAME: MIGHTY TOTAL INTAKE CLEANER PAGE No.: 6 OF 6
PRODUCT CODE No. SB300 ISSUE DATE: 01/01/05
Alkyl Nitriles and Methylpyrrolidone are listed with the Toxic Substance Control Act (TSCA).
State Regulations: Neither the product or its components are listed with the States of California,
Massachusetts, or Pennsylvania.
Canadian Environmental Protection Act: This product is not listed on the Domestic Substance List.
Canadian Workplace Hazardous Materials Information Systems (WHMIS):
The following Canadian Workplace Hazardous Information System (WHMIS) categories apply to
this product:
Compressed Gas: - Flammable/Combustible: Oxidizer: -
Acutely Toxic: - Other Toxic Effects: - Biohazardous: -
Corrosive: - Dangerously Reactive: -
Disclaimer: "Information contained in this publication, while accurate to the best of the knowledge
and belief of LIFE AUTOMOTIVE PRODUCTS, INC. it is not intended and should not be
construed as a warranty or representation for which LIFE AUTOMOTIVE PRODUCTS, INC.
assumes legal responsibility. Any information or advise obtained from LIFE AUTOMOTIVE
PRODUCTS, INC. otherwise than by means of this publication and whether relating to LIFE
AUTOMOTIVE PRODUCTS, INC. materials or other materials, is also given in good faith.
However, it remains at all times the responsibility of the customer to ensure that LIFE
AUTOMOTIVE PRODUCTS, INC. materials are suitable for the particular purpose intended,
except where LIFE AUTOMOTIVE PRODUCTS, INC. has given specific directions for use in LIFE
AUTOMOTIVE PRODUCTS, INC. finished Products.
Insofar as materials not manufactured or supplied by LIFE AUTOMOTIVE PRODUCTS, INC. are
used in conjunction with or instead of LIFE AUTOMOTIVE PRODUCTS, INC. materials, the
customer should ensure that he has received from the manufacturer or supplier all technical data
and other information relating to such materials before incorporating or using them in a LIFE
AUTOMOTIVE PRODUCTS, INC. Product. LIFE AUTOMOTIVE PRODUCTS, INC. accepts no
liability whatsoever (except otherwise provided by law) arising out of the use of information
supplied, the application, adaptation or processing of the products described herein, the use of
other materials in lieu of LIFE AUTOMOTIVE PRODUCTS, INC. material or the use of LIFE
AUTOMOTIVE PRODUCTS, INC. material in conjunction with other materials, except as directed
by LIFE AUTOMOTIVE PRODUCTS, INC.."
Friday, January 19, 2007
Page 1 of 4
MSDS - Material Safety Data Sheet
I. Basic Information:
Contact: Not Available
Manufacturer: LIFE AUTOMOTIVE PRODUCTS INC.
Not Available
Address: 1210 MIDAS COVE, SUITE 101 Information Telephone Number:
City, ST Zip: CORDOVA, TN 38018 Emergency Contact: CHEMTREC
Country: Emergency Telephone Number: 800-424-9300
Emergency Restrictions:
Product Name: MIGHTY AUTO PARTS VS7 SYNTRAMAX COMPLETE FUEL SYSTEM CLEANER
MSDS No.: SB304
Issue Date: 01/17/2007
Supersedes Date: Not Available
II. Hazards Identification:
EMERGENCY OVERVIEW
Danger: Harmful or fatal if swallowed. Eye and skin irritant. Combustible.
OSHA Regulatory Status
This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Potential Health Effects
Route(s) of Entry:
Absorption, Inhalation, and Ingestion.
Health Hazards (Acute and Chronic):
See signs and symptoms below
Signs and Symptoms:
Eye Contact: Irritant. Prolonged contact may cause conjunctivitis.
Skin Contact: Irritant. Defatting of tissue, dermatitis may occur.
Inhalation: Irritant to mucous membranes. Repeated exposure may cause narcosis..
Ingestion: HARMFUL OR FATAL IF SWALLOWED. May cause burns to mouth, throat & stomach.
Medical Conditions Generally Aggravated by Exposure:
Non Known
Other Health Warnings:
Vomiting and subsequent aspiration into the lungs may lead to chemical pneumonia and pulmonary edema which is a potentially fatal condition.
Potential Environmental Effects
Not Available
III. Composition/Information on Ingredients:
Chemical Name CAS No. % Range Trade Secret
1,2,4-Trimethylbenzene 1.0 - 5.0
95-63-6
Aliphatic Hydrocarbon Solvent 60.0 - 100.0
8052-41-3
Hydrocarbon Solvent 7.0 - 13.0
Proprietary
Mesitylene 3.0 - 7.0
108-67-8
Petroleum naphtha 1.0 - 5.0
64742-94-5
Polyether amine 7.0 - 13.0
Proprietary
Xylene (mixed isomers) 1.0 - 5.0
1330-20-7
IV. First Aid Measures:
Emergency and First Aid Procedures:
Friday, January 19, 2007
Page 2 of 4
MSDS - Material Safety Data Sheet
Eye Contact: Flush eyes with clean water for 20 minutes while lifting eyelids. Get prompt medical attention.
Skin Contact: Wash skin with soap and water thoroughly. If adverse effects persist, get prompt medical attention. Remove and isolate contaminated
clothing. Launder contaminated clothing before reuse.
Inhalation: Move victim to fresh air. If breathing becomes difficult, administer oxygen and get prompt medical attention. If breathing stops, give artificial
respiration and get prompt medical attention.
Ingestion: DO NOT INDUCE VOMITING! Call Poison Control Center, physician, or hospital emergency room immediately. Aspiration of vomit into the lungs
can cause pneumonitis, which can be fatal.
Note to Physicians:
N/E
V. Fire Fighting Measures:
Suitable Extinguishing Media:
Water Fog, Foam, Carbon Dioxide, Dry Chemical
Unsuitable Extinguishing Media:
Do not use forced water stream as this could cause the fire to spread.
Products of Combustion:
Carbon dioxide, carbon monoxide, and various hydrocarbons
Protection of Firefighters:
Wear self-contained positive pressure breathing apparatus and protective clothes. Use shield to protect from rupturing and venting containers. At elevated
temperatures containers may vent, rupture or burst, even violently
VI. Accidental Release Measures:
Personal Precautions:
Eliminate all ignition sources. Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed.
Environmental Precautions:
Prevent run-off to sewers, streams, or other bodies of water. If run-off occurs, notify proper authorities as required that a spill has occurred. Run off to sewer
may create fire or explosion hazard.
Methods for Containment:
Dike or contain spill and absorb with inert materials (sand, sawdust, absorbent sweeping compounds, rags, etc).
Methods for Cleanup:
Using a non-metallic scoop, place contaminated material into an approved chemical waste container. Where possible, vacuum spilled liquid using an
explosion proof vacuum to recover material.
Other Information:
All equipment used with handling the concentrate must be grounded. If run-off occurs, notify proper authorities as required that a spill has occurred.
VII. Handling and Storage:
Handling Precautions:
Handling: Use with adequate ventilation and proper protective equipment.
Storage Precautions:
Keep container closed tightly when not in use. Combustible. Store in a cool place below 120 F away from acids, ignition sources and oxidizing agents.
VIII. Exposure Controls/Personal Protection:
Friday, January 19, 2007
Page 3 of 4
MSDS - Material Safety Data Sheet
Chemical Name OSHA PEL ACGIH TLV Other Limits
Polyether amine N/E Not Available
N/E
Hydrocarbon Solvent Not Available Not Available Not Available
Xylene (mixed isomers) 100 ppm (TWA) PA & NJ RTK
100 ppm (TWA)
Petroleum naphtha N/E 100 ppm
N/E
Aliphatic Hydrocarbon Solvent 100 ppm NJ RTK
100 ppm
Mesitylene N/A Not Available
N/A
1,2,4-Trimethylbenzene N/E Not Available
25 ppm
Engineering Controls:
See Section 2 for applicable exposure limits. Maintain adequate ventilation.
Avoid breathing vapors. In restricted areas, use approved chemical filters designed to remove vapor. In confined areas, use approved air line type respirator
or hood. A self-contained breathing apparatus is required for vapor concentrations above TLV limit
Personal Protective Equipment:
See Section 2 for applicable exposure limits. For prolonged exposure wear protective safety glasses, gloves, and apron.
IX. Physical and Chemical Properties:
Boiling Point: >300 F Melting Point: N/D
N/D Freezing Point: N/D
Boiling Range:
Solubility In Water: Insoluble Evaporation Rate (Butyl Acetate = 1): N/D
Flash Point: 140F Flash Point Method: TCC
N/D Light yellow--amber liquid with petroleum
Odor Threshold: Appearance and Odor:
odor.
Vapor Density (AIR = 1): N/D Vapor Pressure (mm Hg.): N/D
N/A N/D
pH Range: Partition Coefficient:
N/D
Decomposition Temp: Auto-Ignition Temp: N/D
Lower Explosive Limit: N/D Upper Explosive Limit: N/D
Specific Gravity (H20 = 1): 0.81
Other Information: N/D
X. Stability and Reactivity:
Stability:
Stable
Conditions to Avoid:
Avoid heat, sparks, and flames. Avoid incompatible materials.
Incompatible Materials:
Oxidizing agents. Open flame, or spark, and acids
Hazardous Decomposition Products:
Fire: Normal products of combustion: carbon monoxide, carbon dioxide, and acrid smoke.
Nitrogen and sulfur oxides
Possibility of Hazardous Reactions:
Will not occur
XI. Toxicological Information:
N/D
Friday, January 19, 2007
Page 4 of 4
MSDS - Material Safety Data Sheet
XII. Ecological Information:
N/D
XIII. Disposal Considerations:
DISPOSAL: This container may be recycled in a recycling centers when empty. Before offering for recycling, empty the can or bottle by using the product
according to the label. If recycling is not available, wrap the container and discard in the trash. Dispose of unused product in accordance with all local, state
government and federal laws and regulations
XIV. Transport Information:
Not Available
Shipping Name:
Not Available Not Available
DOT Hazard Class: DOT Subsidiary Hazard Class:
UN/NA#: Not Available Not Available
MSDSPackGroup:
Transportation Information:
DOT Shipping Name: Not DOT regulated.
DOT Hazard Class: None
The DOT description is provided to assist in the proper shipping classification of this product and may not be suitable for all shipping purposes
XV. Regulatory Information:
See Section 2 for SARA Reportable Chemicals.
USA TSCA: All components of this material are listed on the US TSCA Inventory.
This fuel additive is registered in the United States
XVI. Other Information:
Liquid Gas Solid
Chemical State: X
Pure Mixture
Chemical Type: 2
X
Hazard Category:
2 0
Acute Chronic Fire
X X
Pressure Reactive
Additional Manufacturer Warnings:
Do not used in confined area without proper ventilation. Contact lenses may
2
cause further damage in case of splash into eye. KEEP AWAY FROM
CHILDREN AND ANIMALS! 2
0
N/E: Not Established
N/D: Not Determined H
N/A: Not Applicable
Additional Product Information:
While Life Automotive Products, Inc... believes this data is accurate as of the revision date, we make no warranty with respect to the data
and we expressly disclaim all liability for reliance thereon. The data is offered solely for information, investigation, and verification. Various
government agencies may have specific regulations regarding the transportation, handling, storage, use, or disposal of this product which
may not be covered by this MSDS. The user is responsible for full compliance.
|