3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
Material Safety Data Sheet
Copyright, 2006, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
This material safety data sheet (MSDS) is provided as a courtesy in response to a customer request. This product is not regulated
under, and a MSDS is not required for this product by the OSHA Hazard Communication Standard (29 CFR 1910.1200) because,
when used as recommended or under ordinary conditions, it should not present a health and safety hazard. However, use or
processing of the product not in accordance with the product's recommendations or not under ordinary conditions may affect the
performance of the product and may present potential health and safety hazards.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: Interam(tm) Endothermic E-54A Mat
MANUFACTURER: 3M
DIVISION: Building Safety Solutions Dept
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 10/18/2006
Supercedes Date: 01/31/2006
Document Group: 18-4287-1
Product Use:
Specific Use: Fire barrier wrap.
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Alumina Trihydrate 21645-51-2 65 - 75
Refractory Ceramic Fibers (RCF) 142844-00-6 10 - 15
Copolymer Trade Secret 5 - 10
Steel Foil None 0- 6
Aluminum Foil None 0- 3
Cellulose 9004-34-6 1- 3
Ethylhexyldiphenyl Phosphate 1241-94-7 1- 3
Oxide Glass Chemicals 65997-17-3 1- 3
Scrim None 0.5 - 1
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Specific Physical Form: Roll of material
_________________________________________________________________________________________________
Page 1 of 7
3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
Odor, Color, Grade: White mat with metal foil on one side, no odor
General Physical Form: Solid
Immediate health, physical, and environmental hazards: The environmental properties of this product present a low
environmental hazard. This product, when used under reasonable conditions and in accordance with the 3M directions for use, should
not present a health hazard. However, use or processing of the product in a manner not in accordance with the product's directions for
use may affect the performance of the product and may present potential health and safety hazards.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
During cutting:
Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion.
Skin Contact:
During cutting:
Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching.
Inhalation:
During cutting:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose
and throat pain.
Ingestion:
No health effects are expected.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
No Data Available
Autoignition temperature
Not Applicable
Flash Point
Not Applicable
Flammable Limits - LEL
Not Applicable
Flammable Limits - UEL
Not Applicable
OSHA Flammability Classification:
5.2 EXTINGUISHING MEDIA
Non-combustible. Choose material suitable for surrounding fire.
_________________________________________________________________________________________________
Page 2 of 7
3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: No unusual fire or explosion hazards are anticipated.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Not applicable.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Avoid breathing of dust created by cutting, sanding, grinding or machining. This product is considered to be an article which does not
release or otherwise result in exposure to a hazardous chemical under normal use conditions. For industrial or professional use only.
7.2 STORAGE
Store under normal warehouse conditions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide appropriate local exhaust for cutting, grinding, sanding or machining. Use in
a well-ventilated area. If exhaust ventilation is not available, use appropriate respiratory protection. Use general dilution ventilation
and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits and/or control dust, fume, or
airborne particles. If ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
The following eye protection(s) are recommended: Safety Glasses with side shields.
8.2.2 Skin Protection
Avoid prolonged or repeated skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the
results of an exposure assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate
compatible materials. Gloves made from the following material(s) are recommended: Butyl Rubber. The following protective
clothing material(s) are recommended: Coveralls - Disposable, Tyvek.
8.2.3 Respiratory Protection
Avoid breathing of dust created by cutting, sanding, grinding or machining. Select one of the following NIOSH approved respirators
based on airborne concentration of contaminants and in accordance with OSHA regulations: Half facepiece or fullface air-purifying
respirator with N95 particulate filters. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-
243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not ingest.
_________________________________________________________________________________________________
Page 3 of 7
3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
Cellulose ACGIH TWA 10 mg/m3
Cellulose OSHA TWA, respirable 5 mg/m3 Table Z-1
Cellulose OSHA TWA, as total dust 15 mg/m3 Table Z-1
Oxide Glass Chemicals 3M TWA, as dust 10 mg/m3
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Roll of material
Specific Physical Form:
White mat with metal foil on one side, no odor
Odor, Color, Grade:
Solid
General Physical Form:
No Data Available
Autoignition temperature
Not Applicable
Flash Point
Not Applicable
Flammable Limits - LEL
Not Applicable
Flammable Limits - UEL
Not Applicable
Boiling point
No Data Available
Specific Gravity
No Data Available
Melting point
Nil
Solubility in Water
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: None known
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide Not Specified
Carbon dioxide Not Specified
Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous
decomposition products may occur as a result of oxidation, heating, or reaction with another material.
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
_________________________________________________________________________________________________
Page 4 of 7
3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
Not applicable.
CHEMICAL FATE INFORMATION
Not applicable.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Dispose of waste product in a sanitary landfill. As a disposal alternative, incinerate in an industrial or
commercial facility.
EPA Hazardous Waste Number (RCRA): Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
98-0400-5465-6, 98-0400-5469-8, 98-0400-5475-5, 98-0400-5477-1
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - No Delayed Hazard - No
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
_________________________________________________________________________________________________
Page 5 of 7
3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 0 Flammability: 1 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
HMIS Hazard Classification
Health: 0 Flammability: 1 Reactivity: 0 Protection: X - See PPE section.
Hazardous Material Identification System (HMIS? hazard ratings are designed to inform employees of chemical hazards in the workplace. These
ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency
situations. HMIS?ratings are to be used with a fully implemented HMIS?program. HMIS?is a registered mark of the National Paint and Coatings
Association (NPCA).
Revision Changes:
Section 1: Product name was modified.
Section 3: Potential effects from inhalation information was modified.
Section 5: Unusual fire and explosion hazard information was modified.
Section 6: Release measures information was modified.
Section 7: Handling information was modified.
Section 8: Engineering controls information was modified.
Section 8: Skin protection phrase was modified.
Section 13: Waste disposal method information was modified.
Section 2: Ingredient table was modified.
Page Heading: Product name was modified.
Section 15: 311/312 Immediate Hazard score was modified.
Section 8: Exposure guidelines ingredient information was modified.
Sections 3 and 9: Odor, color, grade information was modified.
Section 9: Specific gravity information was modified.
Section 12: Ecotoxicological phrase was modified.
Section 12: Chemical Fate phrase was modified.
Section 1: Product use information was added.
Section 1: Product use heading was added.
Section 8: Respiratory protection information was added.
Section 10: Hazardous decomposition or by-products phrase was added.
Section 4: First aid for ingestion (swallowing) - none - was added.
Section 10: Hazardous decompostion heading was added.
Section 8: Eye/face protection phrase was deleted.
Section 4: First aid for ingestion (swallowing) - decontamination - was deleted.
Section 4: First aid for ingestion (swallowing) - intervention - was deleted.
Section 4: First aid for ingestion (swallowing) - medical assistance - was deleted.
Section 9: Density information was deleted.
Section 9: Vapor density value was deleted.
Section 9: Vapor pressure value was deleted.
Section 9: pH information was deleted.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
_________________________________________________________________________________________________
Page 6 of 7
3M MATERIAL SAFETY DATA SHEET Interam(tm) Endothermic E-54A Mat 10/18/2006
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 7 of 7
|