May 2008 Page 1 of 2
MATERIAL SAFETY DATA SHEET
MAY BE USED TO COMPLY WITH OSHA'S HAZARD COMMUNICATION STANDARD, 29 CFR
1910.1200 AND SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT (SARA) OF 1986
PUBLIC LAW 99-499. STANDARD SHOULD BE CONSULTED FOR SPECIFIC REQUIREMENTS.
CO Industrial Products Phone: 205/424-2772
3100 Morgan Road 800/247-9908
MANUFACTURER/ EUTECTIC CORPORATION TELEPHONE NUMBER
SUPPLIERS NAME: N94 W14355 Garwin Mace Drive 1-800-558-8524
Menomonee Falls, WI 53051 USA
Fax: 205/425-4011
ABRACOR ?EXPRESS (HARDENER)
PRODUCT NAME:
PRODUCT CLASSIFICATION: Composite
IMPORTANT: This section covers the materials from which these products are manufactured. The fumes and
gases produced during normal use of these products are covered in Section V. The term "Hazardous" in "Hazardous
Ingredients" should not only be interpreted as a term required and defined in OSHA Hazard Communication
Standard (29 CFR Part 1910.1200), but also as defined by other regulatory agencies. The chemicals or compounds
subject to reporting under Title III, in Section 313, of the Superfund Amendments and Reauthorization Act (SARA)
are marked by the symbol #.
1. Hazardous Ingredients:
ACGIH TLV
OSHA PEL
mg/m3 mg/m3 CAS #
Ingredient %W/W
FerroSilicon 40 ?70 10 as Fe 5 as Fe 8049-17-0
Modified Polyamines ** 25 ?35 N/E N/E Trade Secret
Phenol # 3? 19 19 108-95-2
Formaldehyde 0.2 ?1.5 0.75 ppm 0.3 ppm ceiling 50-00-0
Exposure limits are subject to change. Contact ACGIH, OSHA, NIOSH, and IARC for current values.
** trade secret # 0045-7000-5268
2. Physical Data:
Color: Black
Appearance: Gritty paste
Odor: Ammonia odor
3. Fire and Explosion Hazard Data:
Flash Point > 200 癋
Flammable Limits-
LFL: N/A
UFL: N/A
Water fog, CO2, dry chemical, foam
Extinguishing Media:
Fire Fighting Equipment: Water or foam may cause frothing which can be violent and life
threatening if sprayed directly into burning liquid. Use self-contained breathing apparatus with full face
piece.
These products as shipped are non-hazardous, nonflammable, non-explosive, and non-reactive.
Rating under National Fire Protection 704: Health, 1: Flammability, 0: Reactivity, 0.
MSDS: ABRACOR ?EXPRESS (HARDENER) Page 2 of 2
4. Reactivity Data:
Stability: Stable
Condition to Avoid: Extreme Heat
Materials to Avoid: Strong oxidizing agents, epoxy resin will cause polymerization.
Hazardous Products: When product burns, may form toxic materials, carbon dioxide and
carbon monoxide, various hydrocarbons, etc.
5. Environmental and Disposal Information:
Spills/Leaks: Scrape or wipe up with suitable material for disposal. Flush
contaminated area with water.
Disposal Method: Deposit in landfill in accordance with all local, state, and federal
regulations or incinerate in accordance with local pollution regulations.
6. Health Hazard Data:
Eye: Corrosive to eyes, may cause severe damage. Vapors may irritate eyes.
Skin Contact: Corrosive to the skin. May cause sensitization. May be toxic if
absorbed through skin.
Ingestion: Product is corrosive to mouth, throat, and stomach. Moderately toxic if
swallowed.
Inhalation: Vapors can be corrosive to respiratory system. May be toxic if inhaled.
Chronic Effects: Product is absorbed through the skin and may cause malaise, discomfort,
injury, and death unless promptly treated.
PRIMARY ROUTES OF ENTRY are the respiratory system, eyes, and/or skin.
PREEXISTING respiratory or allergic conditions may be aggravated in some individuals.
7. First Aid:
Eye: Flush eyes with water for 15 minutes and contact physician.
Skin Contact: Remove contaminated clothing. Wash with soap and water.
Ingestion: Seek medical attention.
Inhalation: Remove to fresh air. Provide oxygen if necessary. Contact physician if
adverse effects occur. Seek medical advice.
8. Handling Precautions:
Exposure Guidelines: None established.
Eye Protection: Chemical Goggles or Face Shield
Ventilation: General mechanical ventilation. Exhaust required for application in
confined areas.
Respiratory Protection: Not required under normal conditions in a well ventilated workplace. At
elevated temperatures, a respirator with cartridges approved for
ammonia is required. Respirator is required while grinding, machining,
or burning.
Protective Equipment: Coveralls or work clothes covering skin, rubber gloves, eye protection.
9. Comments:
The information in this MSDS was obtained from sources we believe are reliable. However, this information is
provided without any representation or warranty, expressed or implied, regarding accuracy or correctness. The
conditions or methods of handling, storage, use, and disposal of the product are beyond our control and may be
beyond our knowledge. For this and other reasons we do not assume responsibility and expressly disclaim liability
of loss, damage, or expense arising from it or in any way connected with the handling, storage, use, or disposal of
the product.
May 2008 Page 1 of 2
MATERIAL SAFETY DATA SHEET
MAY BE USED TO COMPLY WITH OSHA'S HAZARD COMMUNICATION STANDARD, 29 CFR
1910.1200 AND SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT (SARA) OF 1986
PUBLIC LAW 99-499. STANDARD SHOULD BE CONSULTED FOR SPECIFIC REQUIREMENTS.
MANUFACTURER/ EUTECTIC CORPORATION TELEPHONE NUMBER
SUPPLIERS NAME: N94 W14355 Garwin Mace Drive 1-800-558-8524
Menomonee Falls, WI 53051 USA
ABRACOR ?EXPRESS (RESIN)
PRODUCT NAME:
PRODUCT CLASSIFICATION: Wear Resistant Composite
IMPORTANT: This section covers the materials from which these products are manufactured. The fumes and
gases produced during normal use of these products are covered in Section V. The term "Hazardous" in "Hazardous
Ingredients" should not only be interpreted as a term required and defined in OSHA Hazard Communication
Standard (29 CFR Part 1910.1200), but also as defined by other regulatory agencies. The chemicals or compounds
subject to reporting under Title III, in Section 313, of the Superfund Amendments and Reauthorization Act (SARA)
are marked by the symbol #.
1. Hazardous Ingredients:
ACGIH TLV
OSHA PEL
mg/m3 mg/m3 CAS #
Ingredient %W/W
FerroSilicon 40 ?70 10 as Fe 5 as Fe 8049-17-0
Bisphenol A-Epichlorohydrin 22 ?32 N/E N/E 25068-38-6
Trimethylolpropane Triacrylate 5 ?10 N/E N/E 15625-89-5
Exposure limits are subject to change. Contact ACGIH, OSHA, NIOSH, and IARC for current values.
2. Physical Data:
Color: Dark Grey
Appearance: Smooth Thick Paste
Odor: Sweet
3. Fire and Explosion Hazard Data:
Flash Point: > 200 癋
Flammable Limits-
LFL: N/A
UFL: N/A
Water fog, CO2, dry chemical, foam
Extinguishing Media:
Fire Fighting Equipment: Water or foam may cause frothing which can be violent and life
threatening if sprayed directly into burning liquid. Use self-contained
breathing apparatus with full face piece and impervious protective
clothing.
These products as shipped are non-hazardous, nonflammable, non-explosive, and non-reactive.
Rating under National Fire Protection 704: Health, 1: Flammability, 0: Reactivity, 0.
MSDS: ABRACOR ?EXPRESS (RESIN) Page 2 of 2
4. Reactivity Data:
Stability: Stable
Condition to Avoid: Extreme Heat
Materials to Avoid: Strong oxidizing agents, epoxy hardener will cause polymerization,
bases, acids.
Hazardous Products: When product burns, may form toxic materials, carbon dioxide and
carbon monoxide, various hydrocarbons, etc.
5. Environmental and Disposal Information:
Spills/Leaks: Scrape or wipe up with suitable material for disposal. Flush
contaminated area with water.
Disposal Method: Deposit in landfill in accordance with all local, state, and federal
regulations or incinerate in accordance with local pollution regulations.
6. Health Hazard Data:
Eye: May cause eye irritation
Skin Contact: May cause sensitization, reddening, irritation, and dermatitis after
prolonged or repeated exposure.
Ingestion: Single dose toxicity is considered extremely low.
Inhalation: Irritation may be caused. Nausea, vomiting, and/or diarrhea may result.
Chronic Effects: Repeated exposures are not anticipated to cause significant adverse
effects. May aggravate disorders of the skin or lungs.
PRIMARY ROUTES OF ENTRY are the respiratory system, eyes, and/or skin.
PREEXISTING respiratory or allergic conditions may be aggravated in some individuals.
7. First Aid:
Eye: Flush eyes with water for 15 minutes and contact physician.
Skin Contact: Remove contaminated clothing. Wash with soap and water.
Ingestion: Seek medical attention.
Inhalation: Remove to fresh air. Provide oxygen if necessary. Contact physician if
adverse effects occur.
8. Handling Precautions:
Exposure Guidelines: None established.
Ventilation: General mechanical ventilation. Exhaust required for application in
confined areas.
Respiratory Protection: Not ordinarily required, unless grinding or machining of product is
necessary.
Protective Equipment: Coveralls or work clothes covering skin, rubber gloves. Wear goggles
when grinding or machining.
9. Comments:
The information in this MSDS was obtained from sources we believe are reliable. However, this information is
provided without any representation or warranty, expressed or implied, regarding accuracy or correctness. The
conditions or methods of handling, storage, use, and disposal of the product are beyond our control and may be
beyond our knowledge. For this and other reasons we do not assume responsibility and expressly disclaim liability
of loss, damage, or expense arising from it or in any way connected with the handling, storage, use, or disposal of
the product.
|