MATERIAL SAFETY DATA SHEET
SECTION I: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: Powercrete J Part B
CHEMICAL/FAMILY NAME: Modified polyamine
PRODUCT TYPE: Epoxy hardener
MANUFACTURER: Berry Plastics
DIVISION: Corrosion Protection Group
ADDRESS: 11010 Wallisville Road,
Houston, TX, 77013
EMERGENCY TELEPHONE NUMBER: CHEMTREC 1-800-424-9300
OTHER TECHNICAL/HEALTH/SAFETY INFORMATION: (713) 676-0085
SECTION II - HAZARDOUS INGREDIENTS
Specific Chemical Name:
1. Specific chemical identity of this component is confidential.
CAS Number: Proprietary
Common Name: Modified amine
Exposure Limits:
OSHA PEL: Not established
ACGIH TLV: Not established
Carcinogenicity: This chemical has not been reviewed for carcinogenicity by
NTP, IARC, or OSHA.
2. Trimethylhexamethylenediamine
CAS Number: 25620-58-0
Common Name: Not available
Exposure Limits:
OSHA PEL: Not established
ACGIH TLV: Not established
Carcinogenicity: This chemical has not been reviewed for carcinogenicity by
NTP, IARC, or OSHA.
3. Phenol
CAS Number: 108-95-2
Common Name: Not available
Exposure Limits:
Powercrete J Part B Revision 4 Revised: Jan 16, 2009 Page 1 of 5
OSHA PEL: 5 ppm, skin
ACGIH TLV: 5 ppm, skin
Carcinogenicity: This chemical has not een reviewed for carcinogenicity by
NTP, IARC, or OSHA.
SECTION III - PHYSICAL DATA
Appearance and Odor: Clear liquid, amine odor.
Boiling Point: Greater than 392篎 (200篊).
Decomposition Temperature: Greater than 392篎 (200篊).
Solubility in Water: Slightly miscible.
Specific Gravity: 8.2 lbs/gallon at 77篎 (25篊).
Vapor Pressure: 0.3 mm Hg at 68篎 (20篊).
pH: 11.
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
Flash Point: Greater than 200篎 (93篊) closed cup.
Extinguishing Media: Carbon dioxide, foam, dry chemical, water spray.
Fire Fighting Procedures - Special: Use self-contained breathing apparatus.
Unusual Fire and Explosion Hazards: Decomposition and combustion products may be toxic.
SECTION V - REACTIVITY DATA
Stability: Stable.
Incompatibility: Strong oxidizers and acids.
Hazardous Decomposition Products: Carbon monoxide, carbon dioxide, aldehydes, nitrogen
oxides.
Hazardous Polymerization: Will not occur.
SECTION VI - HEALTH HAZARD DATA
Primary Routes of Exposure: Dermal.
Oral LD50: (Rat) 1030 mg/kg.
Dermal LD50: (Rat) 699 mg/kg (component) (Toxic by skin contact).
Inhalation LC50: (Rat) > 0.18 mg/l air 4 hours. No deaths at 14 days.
Sensitization: Potential sensitizer. (Guinea pig) No sensitization observed.
Skin Irritation: Corrosive. Causes burns.
Eye Irritation: Corrosive. Causes burns.
Medical Conditions Aggravated by Exposure: Allergy, eczema, or skin conditions.
Overexposure Effects: Overexposure can cause chemical burns to the skin and eyes and may
result in blindness. Vapors may be severely irritating to the respiratory tract. Considered to
be a dermal toxicant. May affect the central nervous system, liver, and kidneys.
Emergency and First Aid Procedures:
Eyes: Immediately flush eyes for at least 15 minutes with running water. Hold
eyelids apart to ensure rinsing of the entire eye surface and lids with
water. If physician is not available, flush for an additional 15 minutes. Get
immediate medical attention.
Skin: Under a safety shower, immediately remove contaminated clothing and
Powercrete J Part B Revision 4 Revised: Jan 16, 2009 Page 2 of 5
shoes. Wash affected areas thoroughly with large amounts of water, and
soap if available, for at least 15 minutes. Get immediate medical attention.
Discard or decontaminate clothing before reuse and destroy
contaminated shoes.
Ingestion: Immediately give at least 3-4 glasses of water, but do not induce vomiting.
If vomiting occurs, give fluids again. Do not give anything by mouth to an
unconscious or convulsing person. Get immediate medical attention.
Inhalation: Remove from area to fresh air. If not breathing, give artificial respiration.
Get immediate medical attention. If breathing is difficult, transport to
medical care and, if available, give supplemental oxygen.
Other: Promptly remove wet contaminated non-impervious clothing, wash before
reuse. Destroy contaminated leather and absorbent shoes.
SECTION VII - SPILL OR LEAK PROCEDURES
Spill Procedures: Avoid all personal contact. Take up with absorbent material. Shovel into closable
containers. Flush contaminated area with water.
Waste Disposal Methods: Polymerize in bucket. Add each 100 parts of Powercrete J Part A to 11
parts of Powercrete J Part B by weight (Or 5 part A to 1 part B by volume) and
thoroughly mix. Set outdoors until the mixture is set up and cooled down; dispose
in accordance with Federal, State, and local regulations.
SECTION VIII - SPECIAL PROTECTION INFORMATION
Ventilation: Good general mechanical ventilation and local exhaust.
Protective Gloves: Wear impervious gloves.
Eye Protection: Wear splash-proof chemical goggles.
Respiratory Protection: Organic chemical cartridge respirator, if needed.
Other Protective Equipment: Wear appropriate equipment to prevent probability of skin or eye
contact.
SECTION IX - SPECIAL PRECAUTIONS
Emergency Overview: WARNING!
Corrosive to eyes and skin.
Harmful if absorbed through skin.
May cause dermatitis and sensitization and have effects on the central nervous system, liver, and
kidneys.
Avoid contact with eyes, skin, and clothing.
Do not breathe vapor, mist, or spray.
Store in tightly closed containers in dry area.
Use only with adequate ventilation.
Individuals should wash thoroughly after handling.
FOR INDUSTRIAL USE ONLY.
SECTION X - REGULATORY INFORMATION
DOT: Proper Shipping Name: Trimethylhexamethylenediamine
mixture Hazard Class: DOT/IATA/ICAO: 8
IMDG/IMO: 8
ID Number: UN 2327
Packing Group : III
Label Required: Corrosive
OSHA Status: This Material Safety Data Sheet (MSDS) has been prepared in compliance with the
Powercrete J Part B Revision 4 Revised: Jan 16, 2009 Page 3 of 5
Federal OSHA Hazard Communication Standard 29 CFR 1910.1200. This product is
considered to be a hazardous chemical under that standard.
TSCA Inventory Status: Chemical components listed on TSCA Inventory.
SARA/Title III: Section 313 ?Toxic Chemicals: This product is (or contains) a toxic
chemical for routine annual 'Toxic Chemical Release Reporting' under Sec. 313
(40 CFR 372).
108-95-2 Phenol 14.3% concentration This information must be included on all
MSDS's that are copied and distributed for this material.
RCRA: Not a hazardous waste under RCRA (40 CFR 261).
CERCLA: RQ 7000 lbs (U188).
Canadian Inventory Status (CEPA): All components included on the Domestic Substances List
(DSL).
New Jersey Right-to-Know: The following is required composition information:
1. Generic Name: Modified amine NJ Number: 29943300001-5707P
2. Chemical Name: Phenol
CAS Number: 108-95-2
3. Chemical name: Trimethylhexamethylenediamine
CAS Number: 25620-58-0
Pennsylvania Right-to-Know: The following is required composition information:
1. Chemical Name: Phenol
CAS Number: 108-95-2
Comments: Environmental hazard
2. Chemical Name: Confidential
Generic Name: Modified amine
Comments: Not on Pennsylvania Hazardous Substance List.
3. Chemical Name: Trimethylhexamethylenediamine
CAS Number: 25620-58-0
Comments: Not on Pennsylvania Hazardous Substance List.
PREPARATION INFORMATION
DATE OF ISSUE: Jan. 16, 2009 SUPERSEDES: All previous versions
DISCLAIMER
Berry Plastics makes no warranties as to the accuracy or completeness of this information and
disclaims any liability in connection with its use. Berry Plastics obligation shall be only as set forth
in Berry Plastics standard terms and conditions of sale for this product. In no case will Berry
Plastics be liable for any incidental, indirect or consequential damages arising out of the sale,
resale, use or misuse of the product.
The information presented herein was prepared at Berry Plastics by qualified technical personnel,
and to our knowledge it is true and accurate. The information and recommendations are furnished
for this product with the understanding that the purchaser will independently determine the
suitability of the product for this purpose. The data do not constitute a warranty, expressed or
implied, statutory or otherwise, nor are they a representation for which Berry Plastics assumes legal
responsibility. The data are submitted for the user's information and consideration only. Any use of
this product must be determined by the user to be in accordance with the applicable federal, state,
and local laws and regulations.
END
Franklin, MA USA Aarschot, Belgium Comment [AO1]: Se
Tel: +1 508-918-1714 Tel: +32 16 55 36 00 actualizan direcciones
US Toll Free: +1 800-248-0149 Fax: +32 16 55 36 74 y logo
Fax: +1 508-918-1910 E-mail: CPG@berryplastics.com
E-mail: CPG@berryplastics.com
Powercrete J Part B Revision 4 Revised: Jan 16, 2009 Page 4 of 5
Powercrete J Part B Revision 4 Revised: Jan 16, 2009 Page 5 of 5
|