sti Seamless Technologies, Inc. Craftsmanship Technology Service
MATERIAL SAFETY DATA SHEET
SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME(ON LABEL) :SeamTekTM Std. Hardener (Fast Cure), FCH100
COMMON NAME:cycloaliphatic diamine epoxy hardener DATE PRINTED: 12/1/01
DISTRIBUTOR:
SEAMLESS TECHNOLOGIES, INC. EMERGENCY TELEPHONE: CHEMTREC
7460 LANCASTER PIKE - SUITE 9 24 HOURS A DAY 1(800)424-9300
HOCKESSIN, DE 19707 INFORMATION TELEPHONE: 302-234-3750
DATE PREPARED : 5-May-94 PREVIOUS MSDS REVISION DATE: 10-Mar-94
SECTION 2 - COMPOSITION & INFORMATION ON INGREDIENTS
Chemical Name CAS No. Wt % OSHA PEL ACGIH TLV
benzyl alcohol 100-51-6 30-50 N.E. N.E.
cycloaliphatic diamine 1477-55-0 20-40 N.E. N.E.
1,5 pentanediamine, 2 methyl 15520-10-2 5-10 N.E. N.E.
N-aminoethyl piperazine 140-31-8 5-10 N.E. N.E.
108-95-2 3-8 5ppm 5ppm
carbolic acid
salicylic acid 69-72-7 5-12 N.E. N.E.
carbolic acid is listed in SARA III
part 372, section 313.
T.S.C.A. Status - OK on all above components.
SECTION 3 - PHYSICAL & CHEMICAL PROPERTIES
APPEARANCE :clear yellow SPECIFIC GRAVITY (H2O=1.0) :>1.0
PHYSICAL STATE :liquid DENSITY (LB/GAL) :N/A
VAPOR PRESSURE :0.02 mm Hg. MELTING POINT (癈) :N/A
ODOR :amine odor EVAPORATION RATE :N/A
VAPOR DENSITY :N/A (Butyl Acetate = 1)
WATER SOLUBILITY :partially soluble
SECTION 4 - STABILITY & REACTIVITY
STABILITY :Stable.
CONDITIONS TO AVOID :Keep container closed when not in use.
INCOMPATIBILITY :Avoid contact with strong oxidizers or acids.
HAZARDOUS DECOMPOSITION BYPRODUCTS:By fire: carbon dioxide, carbon monoxide,
nitrogen oxide, aldehydes.
HAZARDOUS POLYMERIZATION :Will not occur.
CONDITIONS TO AVOID :Uncontrolled reaction with epoxy resins. Avoid breathing
fumes generated by hardener and epoxy mixture when not used within established pot life.
(Continued on page 2)
SECTION 5 - FIRE & EXPLOSION HAZARD DATA
..\docs\sti\msds\FCH100.DOC
PRODUCT:SeamTekTM Std.Tint Hardener(FastCure) FCH100 DATE PREPARED:3/10/94
Page 2
FLASH POINT (CLOSED CUP METHOD) :220癋 LOWER EXPLOSIVE LIMIT :N/A
UPPER EXPLOSIVE LIMIT :N/A
EXTINGUISHING MEDIA :Foam, CO2, dry chemical, water spray
SPECIAL FIRE FIGHTING PROCEDURES :Wear full protective equipment including self
contained breathing apparatus. Irritating
and/or toxic gases may be generated by fire.
UNUSUAL FIRE AND EXPLOSION HAZARDS :Combustion products may be toxic. Cool storage
containers with water spray to prevent pressure
buildup which could rupture containers.
SECTION 6 - HEALTH HAZARD DATA
ROUTES OF ENTRY: INHALATION? yes SKIN? yes INGESTION? yes
SIGNS AND SYMPTOMS OF OVEREXPOSURE: Irritation of skin.
HEALTH HAZARDS (ACUTE AND CHRONIC):ACUTE:Irritation of skin and
dermatitis.
CHRONIC:Repeated overexposure will cause severe skin irritation, dermatitis and
sensitization. Sensitized persons may experience rapid irritation of skin upon
exposure. NOTE:Persons with lung disorders or who are sensitized should not use
this product.
CARCINOGENICITY: NTP? No IARC MONOGRAPHS? No OSHA REGULATED? No
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY OVEREXPOSURE:
Allergy, skin disorders.
SECTION 7 - FIRST AID PROCEDURES
EYES: Flush with water, holding lids open for 15 minutes or more. Call
physician for advice if necessary.
SKIN: Promptly wash with soap and water. Do not wash with solvents.
Seek medical advice if irritation develops or persists.
INHALATION: Move person to fresh air if effects occur. If needed, give
oxygen or artificial respiration to improve breathing.
Consult physician.
INGESTION: Get medical attention immediately. Never give liquids to an
unconscious or convulsing person.
SECTION 8 - PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Wear protective
clothing to prevent exposure. Stop spill and dike to prevent spreading. Cover
spill with absorbent materials and collect into containers. Clean contaminated
area with detergent and water or a steam cleaner for best results.
WASTE DISPOSAL METHOD: Dispose in accordance with all Federal, State and
Local requirements.
HANDLING AND STORAGE PRECAUTAIONS: Keep containers tightly closed when not in
use.
OTHER PRECAUTIONS: None known.
(Continued on page 3)
SECTION 9 - EXPOSURE CONTROL & PERSONAL PROTECTION
RESPIRATORY PROTECTION: Provide adequate exhaust ventilation and/or NIOSH
approved amine cartridge respirator.
PRODUCT:SeamTekTM Std.Tint Hardener(FastCure) FCH100 DATE PREPARED:3/10/94
Page 3
VENTILATION: LOCAL EXHAUST:if needed SPECIAL: none known
MECHANICAL (GENERAL): Adequate exhaust ventilation must exhaust away from
the applicator.
PROTECTIVE GLOVES: natural rubber or neoprene gloves
EYE PROTECTION: splash goggles or face shield
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Use rubber apron, face shield and
appropriate clothing to prevent contact with skin. Launder contaminated
clothing before reuse. Discard contaminated leather shoes and canvas
sneakers. Protective skin creams help cleaning with soap and water,
however, gloves must still be worn. An eye wash station or an adequate
supply of clean water must be available at the work area.
WORK/HYGIENIC PRACTICES: Enforce careful handling to prevent splashing.
Wash thoroughly after handling.
SECTION 10 - OTHER INFORMATION
HMIS RATINGS: HEALTH :3
FLAMMABILITY :1
REACTIVITY :0
PERSONAL PROTECTION :G
KEY TO ABBREVIATIONS:
N.E. = none established
NOTICE
"The information contained herein is, to the best of our knowledge and belief, accurate.
However, since data, safety standards, and government regulations are subject to change; and the
conditions of handling and use (or misuse) are beyond our control, we make no guarantee of
results, and assume no liability for damages incurred by use or misuse of this material. It is the
responsibility of the user to satisfy himself that he has all current data relevant to his particular
application, and to comply with all applicable Federal, State and local laws and regulations."
END OF MSDS
|