Material Safety Data Sheet
RAMUC TYPE EP WHITE 1 GAL KIT 26630
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
This is a kit that contains the following components:
RAMUC TYPE EP WHITE PART A
RAMUC TYPE EP PART B
1/16
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 1 - PRODUCT IDENTIFICATION
Trade name : RAMUC TYPE EP WHITE PART A
Product code :
COMPANY : Republic Powdered Metals
2628 Pearl Road
Medina, OH 44256
Telephone : (800) 551-7081
Emergency Phone: : After Hours: Chemtrec 1-800-424-9300
SECTION 2 - HAZARDS IDENTIFICATION
Emergency Overview
White. Liquid solution. Vapor may irritate respiratory tract. May cause nausea, headaches, and dizziness.
Leave area to breathe fresh air. Avoid further overexposure. If symptoms persist, get medical attention.
Acute Potential Health Effects/ Routes of Entry
Inhalation Vapor may irritate respiratory tract. May cause nausea, headaches, and dizziness.
:
Eyes Direct contact may cause mild irritation. May cause temporary injury.
:
Ingestion May cause gastrointestinal irritation, nausea, and vomiting.
:
Skin May cause sensitization resulting in irritation, itching and redness.
:
Aggravated Medical Conditions
Pre-existing eye, skin, liver, kidney, and respiratory disorders may be aggravated by exposure.
Chronic Health Effects
Prolonged or repeated exposure to xylene may cause defatting, drying, and irritation of the skin, dermatitis,
central nervous system (CNS) effects, heart muscle sensitization and arrhythmia, hearing loss, and brain, liver,
kidney damage. Xylene overexposure may affect fetal development. Overexposure to methyl isobutyl ketone
can cause narcosis and can adversely affect the central nervous system and cardiovascular system. The
International Agency for Research on Cancer (IARC) has evaluated ethylbenzene and classified it as a possible
human carcinogen (Group 2B) based on sufficient evidence for carcinogenicity in experimental animals, but
inadequate evidence for cancer in exposed humans. Prolonged or repeated exposure to vapors of isopropyl
alcohol can cause eye, skin, or respiratory irritation, headache, dizziness, nausea, in coordination, drowsiness,
and loss of consciousness. Prolonged or repeat exposure to liquid can cause defatting, drying, and irritation of
the skin dermatitis. Overexposure to n-butyl alcohol caused anemia, liver abnormalities, eye, kidney and lung
damage in experimental animals. Can cause eye damage in humans and effect hearing if exposed to vapor
concentrations of over 50 ppm. Fillers are encapsulated and not expected to be released from product under
normal conditions of use.
Target Organs: Skin, Eye, Ingestion, Lung
3/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 3 - PRODUCT COMPOSITION
Chemical Name CAS-No. Weight %
Titanium dioxide 13463-67-7 30.0 - 60.0
Epoxy resin 25036-25-3 30.0 - 60.0
Xylene 1330-20-7 10.0 - 30.0
Methyl isobutyl ketone 108-10-1 7.0 - 13.0
n-Butyl glycidyl ether 2426-08-6 3.0 - 7.0
Ethylbenzene 100-41-4 1.0 - 5.0
n-Butanol 71-36-3 1.0 - 5.0
2-Propanol 67-63-0 1.0 - 5.0
SECTION 4 - FIRST AID MEASURES
Get immediate medical attention for any significant overexposure.
Inhalation : Leave area to breathe fresh air. Avoid further overexposure. If symptoms persist, get
medical attention.
Eye contact : Flush with water for 15 minutes. If irritation persists, get medical attention.
Skin contact : Wash area of contact thoroughly with hand cleaner followed by soap and water. If
irritation, rash or other disorders develop, get medical attention immediately.
Ingestion : Do not induce vomiting unless advised by a physician. Call nearest Poison Control
Center or Physician immediately.
SECTION 5 - FIRE FIGHTING MEASURES
Flash point : 60 ?16 ?br>
F, C
Method : Tag closed cup
Lower explosion limit : Not available.
Upper explosion limit : Not available.
Autoignition temperature : Not available.
Extinguishing media : If water fog is ineffective, use carbon dioxide, dry chemical or foam.
Hazardous combustion : Smoke, fumes.Carbon monoxide and carbon dioxide can form.
products
Protective equipment for : Water may be used to cool containers to minimize pressure build-
firefighters up.Use accepted fire fighting techniques. Wear full firefighting
protective clothing, including self-contained breathing apparatus
(SCBA).
4/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
Fire and explosion conditions : Closed container, may burst when exposed to extreme heat.Empty
containers may contain ignitable vapors.Vapor concentrations in
enclosed areas may ignite explosively.Vapors may travel to sources of
ignition and flashback.
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Use appropriate protective equipment. Avoid contact with material. Remove sources of ignition immediately.
Stop flow of material if safe to do so. Contain spill and keep out of water courses. Ventilate area.
SECTION 7 - HANDLING AND STORAGE
Store under dry warehouse conditions away from heat and all ignition sources. Store in a cool, well ventilated
area. Prevent inhalation of vapor, ingestion, and contact with skin eyes and clothing. Keep container closed
when not in use. Precautions also apply to emptied containers. Do not smoke, weld, generate sparks, or use
flame near container. Change soiled work clothes frequently. Clean hands thoroughly after handling.
SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Personal protection equipment
Respiratory protection : Wear appropriate, properly fitted NIOSH/MSHA approved organic vapor or
supplied air respirator when airborne contaminant level(s) are expected to
exceed exposure limits indicated on the MSDS. Follow manufacturer's
directions for respirator use.
Hand protection : Use suitable impervious nitrile or neoprene gloves and protective apparel to
reduce exposure.
Eye protection : Chemical splash goggles.
Protective measures : Use professional judgment in the selection, care, and use.
Engineering measures : Use only in well ventilated areas. Provide maximum ventilation in enclosed
areas.Use general ventilation and/ or local exhaust to reduce the airborne
contaminant concentration below the exposure limit listed in the MSDS
Exposure Limits
Chemical Name CAS Number Regulation Limit Form
Titanium dioxide 13463-67-7 ACGIH TWA: 10 mg/m3
OSHA PEL: 15 mg/m3 Total dust.
OSHA TWA: 15 mg/m3 Total dust.
OSHA TWA: 5 mg/m3 Respirable fraction.
Xylene 1330-20-7 ACGIH TWA: 100 ppm
ACGIH STEL: 150 ppm
OSHA PEL: 435 mg/m3
5/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
Chemical Name CAS Number Regulation Limit Form
Methyl isobutyl ketone 108-10-1 ACGIH TWA: 50 ppm
ACGIH STEL: 75 ppm
OSHA PEL: 410 mg/m3
n-Butyl glycidyl ether 2426-08-6 ACGIH TWA: 25 ppm
OSHA PEL: 270 mg/m3
Ethylbenzene 100-41-4 ACGIH TWA: 100 ppm
ACGIH STEL: 125 ppm
OSHA PEL: 435 mg/m3
n-Butanol 71-36-3 ACGIH TWA: 20 ppm
OSHA PEL: 300 mg/m3
2-Propanol 67-63-0 ACGIH TWA: 200 ppm
ACGIH STEL: 400 ppm
OSHA PEL: 980 mg/m3
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
Form : Liquid solution
Color : White
Odor : Solvent
pH : Not available.
Vapour pressure : Not available.
Vapor density : Heavier than air
Melting point/range : Not available.
Freezing point : Not available.
Boiling point/range : 237 - 243 ?114 - 117 癈at 760 mmHg
F,
Water solubility : Negligible
Specific Gravity : 1.23
% Volatile Weight : 26 %
SECTION 10 - REACTIVITY / STABILITY
Substances to avoid : Epoxy curing agents.Amines and oxidizing agents.
Stability : Material is stable under normal storage, handling, and use.
Hazardous polymerization : Will not occur.
6/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 11 - TOXICOLOGICAL INFORMATION
Xylene, CAS-No.: 1330-20-7
Acute oral toxicity (LD-50 oral) 3,523 - 8,600 mg/kg ( Rat )
Acute inhalation toxicity (LC-50) 6,350 mg/l ( Rat )
Methyl isobutyl ketone, CAS-No.: 108-10-1
Acute oral toxicity (LD-50 oral) 2,080 mg/kg ( Rat )
n-Butyl glycidyl ether, CAS-No.: 2426-08-6
Acute oral toxicity (LD-50 oral) 2,000 mg/kg ( Rat )
Acute inhalation toxicity (LC-50) 670 mg/l ( Rat ) 3,500 mg/l ( Mouse )
Ethylbenzene, CAS-No.: 100-41-4
Acute oral toxicity (LD-50 oral) 3,500 mg/kg ( Rat )
Acute dermal toxicity (LD-50 dermal) 17,800 mg/kg ( Rabbit )
n-Butanol, CAS-No.: 71-36-3
Acute oral toxicity (LD-50 oral) 790 mg/kg ( Rat )
Acute inhalation toxicity (LC-50) 8,000 mg/l ( Rat )
Acute dermal toxicity (LD-50 dermal) 3,400 mg/kg ( Rabbit )
2-Propanol, CAS-No.: 67-63-0
Acute oral toxicity (LD-50 oral) 4,700 - 5,800 mg/kg ( Rat )
Acute dermal toxicity (LD-50 dermal) 5,030 - 7,900 mg/kg ( Rabbit )
SECTION 12 - ECOLOGICAL INFORMATION
No Data Available
SECTION 13 - DISPOSAL CONSIDERATIONS
RCRA Class : D001: Reportable Quantity = 100 lbs. (Characteristic of ignitability)
This classification applies only to the material as it was originally produced.
Disposal Method : Dispose of hazardous waste according to all local, state, federal and provincial
regulations.
SECTION 14 - TRANSPORTATION / SHIPPING DATA
TDG / DOT Shipping Description:
FLAMMABLE LIQUID, N.O.S., 3, UN1263, PG III
7/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 15 - REGULATORY INFORMATION
North American Inventories:
All components are listed or exempt from the TSCA inventory.
This product or its components are listed on, or exempt from the Canadian Domestic Substances List.
U.S. Federal Regulations:
SARA 313 Components : Xylene 1330-20-7
Methyl isobutyl ketone 108-10-1
Ethylbenzene 100-41-4
n-Butanol 71-36-3
SARA 311/312 Hazards : Acute Health Hazard
Fire Hazard
OSHA Hazardous Components :
Titanium dioxide 13463-67-7
Xylene 1330-20-7
Methyl isobutyl ketone 108-10-1
n-Butyl glycidyl ether 2426-08-6
Ethylbenzene 100-41-4
n-Butanol 71-36-3
2-Propanol 67-63-0
OSHA Status: Considered : Irritant
hazardous based on the
following criteria:
OSHA Flammability : IB
When appropriately mixed with the other part, product has a VOC less water and exempt solvent of:
340 g/l
U.S. State Regulations:
MASS RTK Components : Titanium dioxide 13463-67-7
Xylene 1330-20-7
Methyl isobutyl ketone 108-10-1
n-Butyl glycidyl ether 2426-08-6
Ethylbenzene 100-41-4
n-Butanol 71-36-3
2-Propanol 67-63-0
Penn RTK Components : Titanium dioxide 13463-67-7
Epoxy resin 25036-25-3
Xylene 1330-20-7
Methyl isobutyl ketone 108-10-1
n-Butyl glycidyl ether 2426-08-6
Ethylbenzene 100-41-4
n-Butanol 71-36-3
2-Propanol 67-63-0
8/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP WHITE PART A
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
NJ RTK Components : Titanium dioxide 13463-67-7
Epoxy resin 25036-25-3
Xylene 1330-20-7
Methyl isobutyl ketone 108-10-1
n-Butyl glycidyl ether 2426-08-6
Ethylbenzene 100-41-4
n-Butanol 71-36-3
2-Propanol 67-63-0
Chemicals known to the State of California to cause cancer birth defects and/or other reproductive harm:
100-41-4 Ethylbenzene
108-88-3 Toluene
14808-60-7 Crystalline Silica (Quartz)/ Silica Sand
SECTION 16 - OTHER INFORMATION
HMIS Rating :
Health 2 0 = Minimum
1 = Slight
Flammability 3
2 = Moderate
Reactivity 1
3 = Serious
PPE
4 = Severe
Further information:
For Industrial Use Only. Keep out of Reach of Children. The hazard information herein is offered solely for the
consideration of the user, subject to their own investigation of compliance with applicable regulations, including
the safe use of the product under every foreseeable condition.
Prepared by: Rich Mikol
Legend
ACGIH - American Conference of Governmental Hygienists PEL - Permissible Exposure Limit
CERCLA - Comprehensive Environmental Response, Compensation, and
RCRA - Resource Conservation and Recovery Act
Liability Act
DOT - Department of Transportation RTK - Right To Know
NTP - National Toxicology Program SARA - Superfund Amendments and Reauthorization Act
EPA - Environmental Protection Agency STEL - Short Term Exposure Limit
HMIS - Hazardous Materials Information System TLV - Threshold Limit Value
IARC - International Agency for Research on Cancer TSCA - Toxic Substances Control Act
MSHA - Mine Safety Health Administration TWA - Time Weighted Average
NDSL - Non-Domestic Substance List V - Volume
NIOSH - National Institute for Occupational Safety and Health VOC - Volatile Organic Compound
WHMIS - Workplace Hazardous Materials Information
DSL - Domestic Substance List
System
OSHA - Occupational Safety and Health Administration
9/16 000000004665
Material Safety Data Sheet
RAMUC TYPE EP PART B
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 1 - PRODUCT IDENTIFICATION
Trade name : RAMUC TYPE EP PART B
Product code :
COMPANY : Republic Powdered Metals
2628 Pearl Road
Medina, OH 44256
Telephone : (800) 551-7081
Emergency Phone: : After Hours: Chemtrec 1-800-424-9300
Product use : Coating
SECTION 2 - HAZARDS IDENTIFICATION
Emergency Overview
Liquid. May cause moderate irritation to the respiratory system. May cause nausea, headaches, and dizziness.
May cause drowsiness, weakness, and fatigue. Move to fresh air. If required, artificial respiration or
administration of oxygen can be performed by trained personnel. Leave area to breathe fresh air. Avoid further
overexposure. If symptoms persist, get medical attention.
Acute Potential Health Effects/ Routes of Entry
Inhalation May cause moderate irritation to the respiratory system. May cause nausea, headaches,
:
and dizziness. May cause drowsiness, weakness, and fatigue.
Eyes Vapor and/or mist may cause eye irritation. Direct contact may cause temporary redness
:
and discomfort.
Ingestion May cause irritation to the mouth, throat and stomach. May cause gastrointestinal
:
irritation, nausea, and vomiting.
Skin May cause moderate irritation.
:
Aggravated Medical Conditions
Pre-existing eye, skin, liver, kidney, and respiratory disorders may be aggravated by exposure.
Chronic Health Effects
Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain
and nervous system damage. Intentional misuse by deliberately concentrating and inhaling contents may be
harmful or fatal. Prolonged or repeated exposure to xylene may cause defatting, drying, and irritation of the
skin, dermatitis, central nervous system (CNS) effects, heart muscle sensitization and arrhythmia, hearing loss,
and brain, liver, kidney damage. Xylene overexposure may affect fetal development. Fillers are encapsulated
and not expected to be released from product under normal conditions of use.
Target Organs: Skin, Eye, Lung, Liver, Kidney, Nerve, Reproductive
11/16 800000020295
Material Safety Data Sheet
RAMUC TYPE EP PART B
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 3 - PRODUCT COMPOSITION
Chemical Name CAS-No. Weight %
Polyamide resin NJTSRN# 51721300-5364P > 60.0
Xylene 1330-20-7 30.0 - 60.0
Triethylenetetramine 112-24-3 5.0 - 10.0
SECTION 4 - FIRST AID MEASURES
Get immediate medical attention for any significant overexposure.
Inhalation : Move to fresh air. If required, artificial respiration or administration of oxygen can be
performed by trained personnel.Leave area to breathe fresh air. Avoid further
overexposure. If symptoms persist, get medical attention.
Eye contact : Flush with water for at least 15 minutes while holding eye lids apart. Get medical
attention immediately.
Skin contact : Clean area of contact thoroughly using soap and water. If irritation, rash or other
disorders develop, get medical attention immediately.
Ingestion : Do not induce vomiting unless advised by a physician. Call nearest Poison Control
Center or Physician immediately.
SECTION 5 - FIRE FIGHTING MEASURES
Flash point : 85 ?29 ?br>
F, C
Method : Tag Closed Cup
Lower explosion limit : Not available.
Upper explosion limit : Not available.
Autoignition temperature : Not available.
Extinguishing media : If water fog is ineffective, use carbon dioxide, dry chemical or foam.
Hazardous combustion : Smoke, fumes.Carbon monoxide and carbon dioxide can form.Nitrogen
products oxides can form.
Protective equipment for : Use accepted fire fighting techniques. Wear full firefighting protective
firefighters clothing, including self-contained breathing apparatus (SCBA).Water
may be used to cool containers to minimize pressure build-up.
Fire and explosion conditions : Vapor concentrations in enclosed areas may ignite explosively.Product
may ignite if heated in excess of its flash point.Vapors may travel to
sources of ignition and flashback.Closed container, may burst when
exposed to extreme heat.Empty containers may contain ignitable
vapors.
12/16 800000020295
Material Safety Data Sheet
RAMUC TYPE EP PART B
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 6 - ACCIDENTAL RELEASE MEASURES
Use appropriate protective equipment. Avoid contact with material. Remove sources of ignition immediately.
Stop flow of material if safe to do so. Contain spill and keep out of water courses. Ventilate area.
SECTION 7 - HANDLING AND STORAGE
Prevent inhalation of vapor, ingestion, and contact with skin eyes and clothing. Keep container closed when
not in use. Precautions also apply to emptied containers. To prevent generation of static discharges, use
bonding/grounding connection when pouring liquid. Extinguish all ignition sources including pilot lights, non-
explosion proof motors and electrical equipment until vapors dissipate. Personal protective equipment must be
worn during maintenance or repair of contaminated mixer, reactor, or other equipment. Keep container closed
when not in use. Vapor may migrate to sources of ignition. Do not smoke, weld, generate sparks, or use flame
near container. Store in sealed containers in a cool, dry, ventilated warehouse location.
SECTION 8 - EXPOSURE CONTROLS / PERSONAL PROTECTION
Personal protection equipment
Respiratory protection : Wear appropriate, properly fitted NIOSH/MSHA approved organic vapor or
supplied air respirator when airborne contaminant level(s) are expected to
exceed exposure limits indicated on the MSDS. Follow manufacturer's
directions for respirator use.
Hand protection : Use suitable impervious nitrile or neoprene gloves and protective apparel to
reduce exposure.
Eye protection : Wear appropriate eye protection.Wear chemical safety goggles and/or face
shield to prevent eye contact. Do not wear contact lenses. Do not touch eyes
with contaminated body parts or materials. Have eye washing facilities readily
available.
Protective measures : Use professional judgment in the selection, care, and use.Inspect and replace
equipment at regular intervals.
Engineering measures : Use only in well ventilated areas. Provide maximum ventilation in enclosed
areas.Use local exhaust when the general ventilation is inadequate.
Exposure Limits
Chemical Name CAS Number Regulation Limit Form
Xylene 1330-20-7 ACGIH TWA: 100 ppm
ACGIH STEL: 150 ppm
OSHA PEL: 435 mg/m3
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
Form : Liquid
13/16 800000020295
Material Safety Data Sheet
RAMUC TYPE EP PART B
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
Odor : Aromatic Solvent
pH : Not available.
Vapour pressure : Not available.
Vapor density : Heavier than air
Melting point/range : Not available.
Freezing point : Not available.
Boiling point/range : Not available.
Water solubility : Negligible
Specific Gravity : 0.93
% Volatile Weight : 30 %
SECTION 10 - REACTIVITY / STABILITY
Substances to avoid : Oxidizing agents.Strong acids.Strong bases.
Stability : Stable under normal conditions. Avoid welding arcs, flames or other high
temperature sources.
Hazardous polymerization : Will not occur.
SECTION 11 - TOXICOLOGICAL INFORMATION
Xylene, CAS-No.: 1330-20-7
Acute oral toxicity (LD-50 oral) 3,523 - 8,600 mg/kg ( Rat )
Acute inhalation toxicity (LC-50) 6,350 mg/l ( Rat )
SECTION 12 - ECOLOGICAL INFORMATION
No Data Available
SECTION 13 - DISPOSAL CONSIDERATIONS
RCRA Class : D001: Reportable Quantity = 100 lbs. (Characteristic of ignitability)
This classification applies only to the material as it was originally produced.
Disposal Method : Subject to hazardous waste treatment, storage, and disposal requirements under
RCRA. Recycle or incinerate waste at EPA approved facility or dispose of in
compliance with federal, state and local regulations.
14/16 800000020295
Material Safety Data Sheet
RAMUC TYPE EP PART B
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 14 - TRANSPORTATION / SHIPPING DATA
TDG / DOT Shipping Description:
PAINT, 3, UN1263, PG III
SECTION 15 - REGULATORY INFORMATION
North American Inventories:
All components are listed or exempt from the TSCA inventory.
This product or its components are listed on, or exempt from the Canadian Domestic Substances List.
U.S. Federal Regulations:
SARA 313 Components : Xylene 1330-20-7
SARA 311/312 Hazards : Acute Health Hazard
Fire Hazard
OSHA Hazardous Components :
Xylene 1330-20-7
OSHA Status: Considered : Irritant
hazardous based on the
following criteria:
OSHA Flammability : IC
When appropriately mixed with the other part, product has a VOC less water and exempt solvent of:
326 g/l
U.S. State Regulations:
MASS RTK Components : Xylene 1330-20-7
Triethylenetetramine 112-24-3
Penn RTK Components : Polyamide resin NJTSRN# 51721300-5364P
Xylene 1330-20-7
Triethylenetetramine 112-24-3
NJ RTK Components : Polyamide resin NJTSRN# 51721300-5364P
Xylene 1330-20-7
Triethylenetetramine 112-24-3
Chemicals known to the State of California to cause cancer birth defects and/or other reproductive harm:
None known.
15/16 800000020295
Material Safety Data Sheet
RAMUC TYPE EP PART B
Version 1 Print Date 10/20/2005
REVISION DATE: 08/01/2005
SECTION 16 - OTHER INFORMATION
HMIS Rating :
Health 2 0 = Minimum
1 = Slight
Flammability 3
2 = Moderate
Reactivity 1
3 = Serious
PPE
4 = Severe
Further information:
For Industrial Use Only. Keep out of Reach of Children. The hazard information herein is offered solely for the
consideration of the user, subject to their own investigation of compliance with applicable regulations, including
the safe use of the product under every foreseeable condition.
Prepared by: Rich Mikol
Legend
ACGIH - American Conference of Governmental Hygienists PEL - Permissible Exposure Limit
CERCLA - Comprehensive Environmental Response, Compensation, and
RCRA - Resource Conservation and Recovery Act
Liability Act
DOT - Department of Transportation RTK - Right To Know
NTP - National Toxicology Program SARA - Superfund Amendments and Reauthorization Act
EPA - Environmental Protection Agency STEL - Short Term Exposure Limit
HMIS - Hazardous Materials Information System TLV - Threshold Limit Value
IARC - International Agency for Research on Cancer TSCA - Toxic Substances Control Act
MSHA - Mine Safety Health Administration TWA - Time Weighted Average
NDSL - Non-Domestic Substance List V - Volume
NIOSH - National Institute for Occupational Safety and Health VOC - Volatile Organic Compound
WHMIS - Workplace Hazardous Materials Information
DSL - Domestic Substance List
System
OSHA - Occupational Safety and Health Administration
16/16 800000020295
|