MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product name: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING
SLOW ADH PT A
Product Use/Class: URETHANE ADHESIVE, PART 1 OF 2
Reference: Applies to Stock Number 127EZ, 128EZ New & Improved & T24, TF24
TRANSPORTATION EMERGENCY:
LORD CORPORATION CHEMTREC 24 HR EMERGENCY NO.
111 LORD DRIVE 800 424-9300
(Outside Continental U.S. 703 527-3887)
CARY, NC 27511-8012
NON-TRANSPORTATION EMERGENCY:
INFORMATION TELEPHONE: 814 763-2345
814 868-0924
EFFECTIVE DATE: 02/05/2007
2. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS Number Weight % ACGIH TLV- ACGIH TLV- OSHA PEL- OSHA PEL- Skin
Less Than TWA STEL TWA CEILING
Diphenylmethane 26447-40-5 20.0 % N.E. N.E. N.E. N.E. N.A.
diisocyanate
Aromatic PROPRIETARY 15.0 % 0.005 ppm N.E. N.E. 0.2 mg/m3 N.A.
polyisocyanate 0.02 ppm
4,4'-Diphenylmethane 101-68-8 10.0 % 0.005 ppm N.E. N.E. 0.2 mg/m3 N.A.
diisocyanate 0.02 ppm
N.A. - Not Applicable, N.E. - Not Established, S - Skin Designation
3. HAZARDS IDENTIFICATION
*** EMERGENCY OVERVIEW ***: Brown Liquid, with No odor. Harmful if inhaled. May cause allergic skin
reaction. May cause allergic respiratory reaction. Causes skin and eye irritation. Causes respiratory tract irritation.
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Causes eye irritation.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT: May cause skin sensitization. May cause dermatitis.
Causes skin irritation. Animal tests have indicated that respiratory sensitization can result from skin contact with certain
isocyanates.
EFFECTS OF OVEREXPOSURE - INHALATION: Possible irritation of the respiratory system can occur causing
a variety of symptoms such as dryness of the throat, tightness of the chest, and shortness of breath. Allergic conditions
can occur in certain individuals with high sensitivity to isocyanates; this may result in asthma-like symptoms. May
cause respiratory sensitization. May cause lung damage.
EFFECTS OF OVEREXPOSURE - INGESTION: Harmful if swallowed. Ingestion is not an expected route of
entry in industrial or commercial uses.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS: May cause long-term lung damage. Chronic skin
contact may cause dermatitis.
PRIMARY ROUTE(S) OF ENTRY: Skin Contact, Inhalation, Ingestion, Eye Contact
4. FIRST AID MEASURES
300000005234
Page: 1
Product: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING SLOW ADH PT A,
Effective Date: 02/05/2007
FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding
eyelids open while flushing. Get prompt medical attention.
FIRST AID - SKIN CONTACT: Flush contaminated skin with large amounts of water while removing contaminated
clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.
FIRST AID - INHALATION: Move person to fresh air. Restore and support continued breathing. If breathing is
difficult, give oxygen. Get immediate medical attention.
FIRST AID - INGESTION: If swallowed, do not induce vomiting. Give victim one or two glasses of water or milk.
Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is
rapidly losing consciousness, unconscious or convulsing.
5. FIRE-FIGHTING MEASURES
FLASH POINT: 201 癋, 93 癈 LOWER EXPLOSIVE LIMIT (%): Not Applicable
Setaflash Closed Cup UPPER EXPLOSIVE LIMIT (%): Not Applicable
AUTOIGNITION TEMPERATURE: N.D.
EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: During a fire, irritating and/or toxic gases and particulate may
be generated by thermal decomposition or combustion. Keep containers tightly closed. Closed containers may rupture
when exposed to extreme heat. Use water spray to keep fire exposed containers cool.
SPECIAL FIREFIGHTING PROCEDURES: Wear full firefighting protective clothing, including self-contained
breathing apparatus (SCBA). If water is used, fog nozzles are preferable.
6. ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Keep non-essential personnel a
safe distance away from the spill area. Avoid breathing vapors. Use self-contained breathing equipment. Notify
appropriate authorities if necessary. Avoid contact. Before attempting cleanup, refer to hazard caution information in
other sections of the MSDS form. Scoop spilled material into an appropriate container for proper disposal. (If necessary,
use inert absorbent material to aid in containing the spill).
7. HANDLING AND STORAGE
HANDLING: Keep closure tight and container upright to prevent leakage. Avoid skin and eye contact. Wash
thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been
read and understood. Empty containers should not be re-used. Use with adequate ventilation.
STORAGE: Store only in well-ventilated areas. Keep container closed when not in use.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
ENGINEERING CONTROLS: Sufficient ventilation in pattern and volume should be provided in order to maintain
air contaminant levels below recommended exposure limits.
RESPIRATORY PROTECTION: This product contains isocyanates which have poor odor warning properties. If
occupational exposure limits are exceeded, a NIOSH approved supplied-air respirator is required. Observe OSHA
regulations (29CFR 1910.134) for respirator use.
SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.
EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where
splashing may occur.
Page: 2
Product: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING SLOW ADH PT A,
Effective Date: 02/05/2007
OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is
likely. Remove and wash contaminated clothing before reuse. Use long-sleeved shirt to minimize skin exposure.
HYGIENIC PRACTICES: Wash hands before eating, smoking, or using toilet facility. Food or beverages should not
be consumed anywhere this product is handled or stored. Wash thoroughly after handling.
9. PHYSICAL AND CHEMICAL PROPERTIES
No N.A.
ODOR: BOILING RANGE:
Brown N.D.
APPEARANCE: VAPOR PRESSURE:
Liquid Heavier than Air
PHYSICAL STATE: VAPOR DENSITY:
N.D. Not Applicable
ODOR THRESHOLD: EVAPORATION RATE:
Insoluble 12.6700 lb/gal
SOLUBILITY IN H2O: DENSITY, LB/GL:
N.A. 0.46 %
pH: VOLATILE BY WEIGHT:
N.D. 0.82 %
FREEZE POINT: VOLATILE BY VOLUME:
N.D.
COEFFICIENT OF WATER/OIL
DISTRIBUTION:
(See section 16 for abbreviation legend)
10. STABILITY AND REACTIVITY
CONDITIONS TO AVOID: High temperatures.
INCOMPATIBILITY: Amines, acids, water, hydroxyl, or active hydrogen compounds.
HAZARDOUS DECOMPOSITION PRODUCTS: Monomeric isocyanate, traces of hydrogen cyanide, nitrogen
dioxide. Carbon monoxide, carbon dioxide.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.
STABILITY: Product is stable under normal storage conditions.
11. TOXICOLOGICAL INFORMATION
No Data
PRODUCT LD50 (ORAL)
No Data
(DERMAL)
No Data
PRODUCT LC50
12. ECOLOGICAL INFORMATION
ECOLOGICAL INFORMATION: No Information
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local
environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and
disposal facility.
14. TRANSPORT INFORMATION
This product is NOT REGULATED for non-bulk road shipments. For the most accurate shipping information, refer to
your transportation/compliance department regarding changes in package size, mode of shipment or other regulatory
descriptors.
Page: 3
Product: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING SLOW ADH PT A,
Effective Date: 02/05/2007
15. REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS: AS FOLLOWS -
This product is considered hazardous as defined by 29 CFR 1910.1200 (OSHA HazCom Standard.)
SARA SECTION 313
This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the
Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372:
Chemical Name CAS Number Weight % Less Than
Diphenylmethane diisocyanate 26447-40-5 20.0 %
Aromatic polyisocyanate PROPRIETARY 15.0 %
4,4'-Diphenylmethane diisocyanate 101-68-8 10.0 %
TOXIC SUBSTANCES CONTROL ACT:
INVENTORY STATUS
The chemical substances in this product are on the TSCA Section 8 Inventory.
EXPORT NOTIFICATION
This product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if
exported from the United States:
NONE
16. OTHER INFORMATION
HMIS RATINGS - HEALTH: 2* FLAMMABILITY: 1 PHYSICAL HAZARD: 0
* - Indicates a chronic hazard; see Section 3
VOLATILE ORGANIC COMPOUNDS
Calculated 0.06 lb/gal, 7 g/l
LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined
DISCLAIMER
The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of
handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred
by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and
regulations.
Page: 4
MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product name: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING
SLOW ADH PT B
Product Use/Class: URETHANE ADHESIVE, PART 2 OF 2
Reference: Applies to Stock Number 127EZ, 128EZ New & Improved & T24, TF24
TRANSPORTATION EMERGENCY:
LORD CORPORATION CHEMTREC 24 HR EMERGENCY NO.
800 424-9300
111 LORD DRIVE
(Outside Continental U.S. 703 527-3887)
CARY, NC 27511 -8012
NON-TRANSPORTATION EMERGENCY:
INFORMATION TELEPHONE: 814 763-2345
814 868-0924
EFFECTIVE DATE: 11/17/2006
2. COMPOSITION/INFORMATION ON INGREDIENTS
THIS PRODUCT IS NOT CONSIDERED HAZARDOUS AS DEFINED BY 29 CFR 1910.1200 (OSHA HAZCOM STANDARD)
3. HAZARDS IDENTIFICATION
*** EMERGENCY OVERVIEW ***: White Liquid, with N o odor. Low hazard for usual industrial or commercial
handling.
EFFECTS OF OVEREXPOSURE - EYE CONTACT: Eye contact may cause slight irritation.
EFFECTS OF OVEREXPOSURE - SKIN CONTACT : No hazard expected in normal industrial use.
EFFECTS OF OVEREXPOSURE - INHALATION: No inhalation hazard expected during normal workplace use.
EFFECTS OF OVEREXPOSURE - INGESTION: Harmful if swallowed. Ingestion is not an expected route of
entry in industrial or commercial uses.
EFFECTS OF OVEREXPOSURE - CHRONIC HAZARDS : None expected under normal working conditions.
PRIMARY ROUTE(S) OF ENTRY: Skin Contact, Inhalation, Ingestion, Eye Contact
4. FIRST AID MEASURES
FIRST AID - EYE CONTACT: Flush eyes immediately with large amount of water for at least 15 minutes holding
eyelids open while flushing. Get prompt medical attention.
FIRST AID - SKIN CONTACT : Flush contaminated skin wi h large amounts of water while removing contaminated
t
clothing. Wash affected skin areas with soap and water. Get medical attention if symptoms occur.
FIRST AID - INHALATION: This material is not likely to be hazardous by inhalation. However, if exposed to
excessive levels of vapor or mist, remove to fresh air, give oxygen if breathing is difficult, and get immediate medical
attention.
FIRST AID - INGESTION: If swallowed, do not induce vomiting. Give victim one or two glasses of water or milk.
Call a physician or poison control center immediately for further instructions. Never give anything by mouth if victim is
rapidly losing consciousness, unconscious or convulsing.
300000005240
Page: 1
Product: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING SLOW ADH PT B ,
Effective Date : 11/17/2006
5. FIRE-FIGHTING MEASURES
FLASH POINT: 201 癋, 93 癈 LOWER EXPLOSIVE LIMIT (%): Not Applicable
Setaflash Closed Cup UPPER EXPLOSIVE LIMIT (%): Not Applicable
AUTOIGNITION TEMPERATURE: N.D.
EXTINGUISHING MEDIA: Carbon Dioxide, Dry Chemical, Foam, Water Fog
UNUSUAL FIRE AND EXPLOSION HAZARDS: Keep containers tightly closed. Closed containers may rupture
when exposed to extreme heat. Use water spray to keep fire exposed containers cool. During a fire, irrita
ting and/or
toxic gases and particulate may be generated by thermal decomposition or combustion.
SPECIAL FIREFIGHTING PROCEDURES : Wear full firefighting protective clothing, including self-contained
breathing apparatus (SCBA). If water is used, fog nozzles are preferable.
6. ACCIDENTAL RELEASE MEASURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED : Avoid breathing vapors. Notify
appropriate authorities if necessary. Contain and remove with inert absorbent material. Avoid contact. Keep non-
essential personnel away from spill area. Before attempting cleanup, refer to hazard caution information in other sections
of the MSDS form.
7. HANDLING AND STORAGE
HANDLING: Keep closure tight and container upright to prevent leakage. Avoid skin and eye contact. Wash
thoroughly after handling. Do not handle until all safety precautions have been read and understood. Empty containers
should not be re-used. Use with adequate ventilation.
STORAGE: Store only in well-ventilated areas. Keep container closed when not in use.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
ENGINEERING CONTROLS : Provide adequate general ventilation where this product is used.
RESPIRATORY PROTECTION: Respiratory protection is not required under normal working conditions where
adequate ventilation is present.
SKIN PROTECTION: Use neoprene, nitrile, or rubber gloves to prevent skin contact.
EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles where
splashing may occur.
OTHER PROTECTIVE EQUIPMENT: Remove and wash contaminated clothing before reuse.
HYGIENIC PRACTICES : Wash hands before eating, smoking, or using toilet facility. Do not smoke in any
chemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or
stored. Wash thoroughly after handling.
9. PHYSICAL AND CHEMICAL PROPERTIES
ODOR: No BOILING RANGE: N.A.
APPEARANCE: White VAPOR PRESSURE: N.D.
PHYSICAL STATE : Liquid VAPOR DENSITY: Not Applicable
ODOR THRESHOLD : N.D. EVAPORATION RATE: Not Applicable
SOLUBILITY IN H2O: Insoluble D ENSITY, LB/GL: 10.89 lb/gal
pH: N.A. VOLATILE BY WEIGHT: 0.00 %
Page: 2
Product: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING SLOW ADH PT B ,
Effective Date : 11/17/2006
FREEZE POINT: N.D. VOLATILE BY VOLUME: 0.00 %
COEFFICIENT OF WATER/OIL N.D.
DISTRIBUTION:
(See section 16 for abbreviation legend)
10. STABILITY AND REACTIVITY
CONDITIONS TO AVOID: High temperatures.
INCOMPATIBILITY Acids, caustics, amines, ammonia, halogens, and isocyanates.
:
HAZARDOUS DECOMPOSITION PRODUCTS : Carbon monoxide, carbon dioxide.
HAZARDOUS POLYMERIZATION: Hazardous polymerization will not occur under normal conditions.
STABILITY: Product is stable under normal storage conditions.
11. TOXICOLOGICAL INFORMATION
PRODUCT LD50 (ORAL) No Data
(DERMAL) No Data
PRODUCT LC50 No Data
12. ECOLOGICAL INFORMATION
ECOLOGICAL INFORMATION: No Information
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local
environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and
disposal facility.
14. TRANSPORT INFORMATION
This product is NOT REGULATED for non-bulk road shipments. For the most accurate shipping information, refer to
your transportation/compliance department regarding changes in package size, mode of shipment or other regulatory
descriptors.
15. REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS: AS FOLLOWS -
This product is not considered hazardous as defined by 29 CFR 1910.1200 (OSHA HazCom Standard.)
SARA SECTION 313
This product contains the following substances subject to the reporting requirements of Section 313 of Title III of the
Superfund Amendment and Reauthorization Act of 1986 and 40 CFR part 372 :
NONE
TOXIC SUBSTANCES CONTROL ACT:
INVENTORY STATUS
Page: 3
Product: FUSOR 127EZ, 128EZ, T24, TF24 PLASTIC BONDING SLOW ADH PT B ,
Effective Date : 11/17/2006
The chemical substances in this product are on the TSCA Section 8 Inventory.
EXPORT NOTIFICATION
This product contains the following chemical substances subject to the reporting requirements of TSCA 12(B) if
exported from the United States:
NONE
16. OTHER INFORMATION
HMIS RATINGS - HEALTH : 1 FLAMMABILITY: 1 PHYSICAL HAZARD: 0
* - Indicates a chronic hazard; see Section 3
VOLATILE ORGANIC COMPOUNDS
Calculated 0 lb/gal, 0 g/l
LEGEND: N.A. - Not Applicable, N.E. - Not Established, N.D. - Not Determined
DISCLAIMER
The information contained herein is, to the best of our knowledge and belief, accurate. However, since the conditions of
handling and use are beyond our control, we make no guarantee of results, and assume no liability for damages incurred
by use of this material. It is the responsibility of the user to comply with all applicable federal, state and local laws and
regulations.
Page: 4
|