MATERIAL SAFETY DATA SHEET
SECTION I - PRODUCT INFORMATION
?br>
No Warp, Window and Door, Frame and Jamb Sealant
Products: Touch 'n Seal
Manufacturer:
Convenience Products
866 Horan Drive
Fenton, MO 63026-2416 USA
Emergency Number: 1-800-424-9300 (Chemtrec) (636) 349-5333 (Convenience Products)
Prepared by Jay ZHANG Approved by Dr. Joe Lott July 11,2002
SECTION II - HAZARDOUS INGREDIENTS/IDENTITY INFORMATION
CHEMICAL NAME CAS NO. OSHA PEL ACGIH TLV PERCENTAGE
Polyurethane 328235-05-8 0.02 ppm 0.005 ppm 35-75
Prepolymer containing
Methylene bisphenyl
isocyanate (CAS# 101-
68-8)
Polyether Polyol Mixture *NE *NE 10-40
Dimethylether 115-10-6 *NE *NE 0-8
Propane 74-98-6 1000 ppm 1000 ppm 2-10
Isobutane 75-28-5 *NE *NE 2-10
* Not established
** None of the components in this product are listed by IARC, NTP, OSHA or ACGIH as a carcinogen.
HMIS Health 3 Flammability 4 Reactivity 1
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
Boiling Point -43.7篎 (-42篊) (Estimated for Propellant)
Vapor Pressure 165 psig at 130?br>
Vapor Density (AIR = 1) Heavier than Air
Specific Gravity (H20 = 1) 1.01 g/ml at 25癈
Solubility in Water N/A
Appearance and Odor Gel under pressure/faint hydrocarbon odor
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
Flash Point Estimated: -156篎 (-104篊)
Flammable Limits in air % by UEL Upper 10% (Estimated)
Volume LEL Lower 1.8% (Estimated)
Extinguishing Media Water fog, foam, CO2 , or dry chemical
Fire fighters should wear full self-contained breathing
Fire Fighting Procedures
apparatus and full protective clothing.
Avoid storage temperatures above 120篎 to prevent can
Unusual Hazards explosions. Avoid water contamination in closed
container.
SECTION V - REACTIVITY DATA
Stable under normal storage and handling conditions. Do
Stability not store above 120篎. Cured foam will deteriorate when
exposed to UV light.
Water, alcohols, strong bases, finely powdered metal
Incompatibility such as aluminum, magnesium or zinc, and strong
oxidizers.
Contamination with water may form CO2. Avoid high heat;
i.e., flames, extremely hot metal surfaces, heating
Conditions/Hazards to Avoid
elements, combustion engines, etc. Do not store in auto
or direct sunlight.
SECTION VI - HEALTH HAZARD DATA
The primary adverse health effects of this material are related to the Polymeric Isocyanate (MDI)
component, and, to a lesser degree, the Liquefied Petroleum Gas (Hydrocarbon) component. Adequate
ventilation should be provided to avoid exceeding the exposure limits of these components. If used
indoors, mechanical ventilation or exhaust should be provided during use and until foam is cured and
vapor of the Liquefied Petroleum Gas (Hydrocarbon) is vented out of the build.
Inhalation MDI vapors may cause irritation of the mucous membranes of the nose, throat or trachea,
which may cause chest discomfort, coughing, and allergic asthma-like sensitivity. Air-borne overexposure
well above the PEL may result additionally in eye irritation, headache, chemical bronchitis, asthma-like
findings or pulmonary edema.
Inhaling concentrated the Liquefied Petroleum Gas (Hydrocarbon) can cause lightheadedness,
headaches, or lethargy. Person with cardiac arrhythmia may be at increased risk in server exposure.
Skin Contact: may result in localized irritation, reddening or swelling. Prolonged or repeated exposure
may lead to sensitization and/or dermatitis.
Eyes Contact: may result in eye irritation and mild corneal opacity due to adhesive character.
Ingestion: may cause irritation of mucous membranes in the mouth and digestive tract.
Emergency and First Aid Procedures
Inhalation - Remove to fresh air. Get immediate medical attention.
Skin ?Immediately clean wet foam from skin, using Touch n' Foam Cleaner or acetone ?do not use water.
If foam dries on skin, apply generous amounts of petroleum jelly or lanolin, put on plastic gloves and wait 1
hour. With a clean cloth, firmly wipe off petroleum jelly and repeat process. Do not attempt to remove dried
foam with solvent. Cured foam wears off and is not harmful to health.
Eye - In case of eye contact, flush with water for 15 minutes. Get immediate medical attention.
Ingestion - In case of ingestion, get immediate medical attention.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
If can ruptures, protect area from heat, sparks, flames, or static
electricity. Turn off sources of ignition. Vapors are heavier than air.
Spills/Leaks
Make sure area is adequately ventilated. Allow foaming process to
complete; then dispose according to federal, state, and local regulation.
Waste Disposal Dispose of cured foam per federal, state, and local regulations.
Container Disposal Dispose according to federal, state, and local regulations.
Always store upright. Storage temperatures: min. 0篎, max. 100癋. Do
Storage
not store containers in direct sunlight.
SECTION VIII - PERSONAL PROTECTION
Respiratory
Not applicable
Protection
Wear gloves and safety glasses. Use in well ventilated areas only. See
Clothing
section IV.
Eye Protection Safety glasses.
Ventilation Maintain local exhaust rate to keep below TLV.
SECTION IX - REGULATORY INFORMATION
SARA - This product contains a toxic chemical (or chemicals) subject to the reporting requirements of
Section 313 of the Emergency Planning and Community Right-to-Know Act of 1986 (40CFR 372).
NAME CAS NO. AMOUNT
Methylene bisphenyl isocyanate 101-68-8 7-20%
CERCLA - Reportable Quantity - yes ...(40CFR 302.4)......(5000 lb. of Methylene bisphenyl isocyanate)
RCRA Hazardous Waste - No
DOT Proper Shipping Name - Consumer Commodity
Diphenylmethane Diisocyanate (cas# 101-68-8) is cited on certain state lists as follow:
NJ2=New Jersey environmental hazardous substance (present at greater than or equal to 1.0%)
NJ3=New Jersey workplace hazardous substance (present at greater than or equal to 1.0%)
PA1=Pennsylvania hazardous substance (present at greater than or equal to 1.0%)
PA3=New Jersey environmental hazardous substance (present at greater than or equal to 1.0%)
CANADIAN REGULATIONS
WHMIS - The Canadian workplace Hazardous Material Information System Classification: This product is
not a "controlled Product" under WHMIS.
CANADIAN ENVIRONMENTAL PROTECTION ACT (CEPA):
All substances in this product are listed on the Canadian Domestic Substances List (DSL) or are not
required to list.
The above information is accurate to the best of our knowledge. However, since data, safety
standards, and government regulations are subject to change and the conditions of handling and use
or misuse are beyond our control, Convenience Products makes no warranty, either express or
implied, with respect to the completeness or continuing accuracy of the information contained herein
and disclaims all liability for reliance thereon. User should satisfy himself that he has all current data
relevant to his particular use.
|