MSDS Material Safety Data Sheet
UNITEX
K.C. WHITE ACRYLIC CURE 25% (TYPE II) 1 5
Page of
MSDS Number: 2004 Revision Date: Jan. 24, 2004
1 PRODUCT AND COMPANY IDENTIFICATION
Manufacturer
UNITEX
3101 Gardner Ave.
Kansas City, MO 64120
Contact: Technical Services
Telephone Number: 816-231-7700
FAX Number: 816-483-3149
E-Mail: mail@unitex-chemicals.com
Web www.unitex-chemicals.com
Product Name: K.C. WHITE ACRYLIC CURE 25% (TYPE II)
Revision Date: Jan. 24, 2004
MSDS Number: 2004
Product Code: K.C. WHITE ACRYLIC CRE 25% (TYPE II)
Product Use: Solvent-based acylic curing and sealing compounds.
Emergency Telephone No.: 800-424-9300 CHEMTREC 24 hrs.
MSDS Prepared by: Wm. Michael Simmons Director of Safety Phone No.: 800-821-5846
2 COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Cas # Chemical Name Perc.
----------------------------------------------------------------
64742956 | Aromatic 100 Hydrocarbon | 30-40%
1317653 | Calcuim Carbonate | 1-10%
3 HAZARDS IDENTIFICATION
Route of Entry: Eyes, Skin, Ingestion, Inhalation
Target Organs: None known
Inhalation: May cause irritation to nose and throat.
Skin Contact: May cause irritation and dermatitis.
Eye Contact: May cause irritation.
Ingestion: May cause irritation of the mouth, stomach and cause sensitization.
1,2,4-Trimethylbenzene (component in CAS# 64742956)
No exposure limits established
Xylene (component in CAS# 64742956)
OSHA PEL 100 ppm TWA
OSHA VPEL 100 ppm TWA
OSHA VPEL 150 ppm STEL
ACGIH TLV 100 ppm TWA
ACGIH TLV 150 ppm STEL
Cumene (omponent in CAS# 64742956)
MSDS Material Safety Data Sheet
UNITEX
K.C. WHITE ACRYLIC CURE 25% (TYPE II) 2 5
Page of
MSDS Number: 2004 Revision Date: Jan. 24, 2004
OSHA PEL 50 ppm TWA
ACGIH PEL 50 ppm TWA
4 FIRST AID MEASURES
Inhalation: If overexposure occurs, remove victim to fresh air. If breathing stops, administer artificial respiration. Seek
immediate medical attention.
Skin Contact: Remove contaminated clothing as soon at possible. Wash exposed skin thoroughly with soap and water. If
irritation persists, consult a physician. Launder contaminated clothing before reuse. Extremely contaminated
leather shoes should be discarded.
Eye Contact: Flush eyes with plenty of water for at least 15 minutes. If necessary, gently hold open eyelids during the
flush. Immediately seek medical attention.
Ingestion: If large amounts of material is swallowed, do not induce vomiting. Should vomiting occur, be sure to keep
victim's head below hips to avoid aspiration of vomitus into the lungs. Immediately consult a physician. Do
not attempt to give liquid to an unconscious person.
5 FIRE FIGHTING MEASURES
Flash Point: 110 deg. F.
Flash Point Method: Tag Closed Cup Method
Burning Rate: No data available.
Autoignition Temperature: 375 deg. F.
LEL: 1.0%
UEL: 6.5%
Flammability Classificati Combustible Liquid
Other:
Special Fire Fighting Procedures: None. Avoid breathing smoke. NFPA Class B-C fire extinguisher (dry chemical, carbon
dioxide or foam). Water spray may be ineffective on fire but can protect fire fighters and cool closed containers. Avoid
spraying directly into containers to prevent boilover. Explosion hazard when exposed to heat and flame. Vapor is heavier than
air and can travel a considerable distance to a source of ignition and flashback.
Do not pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static electricty, or
other sources of ignition; containers may explode and cause injury or death.
6 ACCIDENTAL RELEASE MEASURES
Small Spills: Eliminate all ignition sources. Contain with earthen dike or petroleum material. Remove with grounded suction
pump to a salvage container. Remove all absorbent and contaminated materials.
Large Spills: For large spills, dike far ahead of liquid for later disposal. Do not release into sewers or waterways.
Cleanup: Remove all absorbent and contaminated materials.
Regulatory Requirements: Follow applicable OSHA regulations (29 CFR 1910.120).
Eliminate all ignition sources (flares, flames including pilot lights, electricial sparks). Persons not wearing protective
equipment should be excluded from area of spill until cleanup has been completed.
MSDS Material Safety Data Sheet
UNITEX
K.C. WHITE ACRYLIC CURE 25% (TYPE II) 3 5
Page of
MSDS Number: 2004 Revision Date: Jan. 24, 2004
7 HANDLING AND STORAGE
Handling Precautions: For professional use only. Avoid eye/skin contact. Wash after using and before eating or
smoking. Avoid breathing vapors. Use as directed. Avoid uncontrolled mixing with oxidizers.
Respiratory protection is required when ventilation is inadequate. NIOSH/OSHA approved
respirators should be provided and worn.
Storage Requirements: Store in a cool/dry location. Do not allow material to freeze, as product may be damaged. Store
away from sparks and open flames.
Containers of this material may be hazardous when emptied. Since containers retain product
residues (vapor, liquid, and/or solid), all hazard precautions given in the data sheet must be
observed. All five gallon pails and larger metal containers, including totes and tank trucks,
should be grounded and/or bonded when material is transfered. Hydrocarbon solvents are
basically non-conductors of electricity and can become electrostatically charged during mixing,
filtering or pumping at high flow rates. If this charge reaches a sufficiently high level, sparks
can form that may ignite the vapors or mists from process equipment operating at elevated
temperature and pressure, or sudden ingess of air into vacuum equipment, may result in
ignition without the presence of obvious ignition sources.
8 EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls:
Protective Equipment: VENTILATION: Provide general or local exhaust systems to maintain airborne concentrations
below OSHA PEL's. Local exhaust ventilation is preferred because it prevents contaminant
dispersion into the work area by controlling it at its source.
RESPIRATORY PROTECTION: Seek professional advice prior to respirator selection and use.
Follow OSHA respirator regulations (29 CFR 1910.134) and, if necessary, wear OSHA/NIOSH
approved respirator. Select respirator based on its suitability to provide adequate worker
protection for given working conditions, level of airborne contamination, and presence of sufficient
oxygen.
PROTECTIVE CLOTHING/EQUIPMENT: Separate contaminated work clothes from street
clothes. Launder before reuse. Remove this material from your work shoes and clean personal
protective equipment.
OTHER PRECAUTIONS: Never eat, drink or smoke in work areas.
9 PHYSICAL AND CHEMICAL PROPERTIES
Appearance: White pigmented
Physical State: Liquid Boiling Point: 311 deg. F.
Odor: Hydrocarbon Freezing/Melting Pt.: NA
pH: No data available Solubility: Negligible
Vapor Pressure: 1.7 mg/Hg @ 78 deg. F Spec Grav./Density: (H2O=1) 1.02
Vapor Density: (Air=1) 4
VOC: Yes
Evap. Rate: (Butly Acetate=1) 8
MSDS Material Safety Data Sheet
UNITEX
K.C. WHITE ACRYLIC CURE 25% (TYPE II) 4 5
Page of
MSDS Number: 2004 Revision Date: Jan. 24, 2004
10 STABILITY AND REACTIVITY
Stability: Stable
Conditions to avoid: Heat and open flame.
Materials to avoid (incompatability): Strong oxidizers.
Hazardous Decomposition products: Can form carbon dioxide, carbon monoxide and other petroleum decomposition
byproducts.
Hazardous Polymerization: Will not occur.
11 TOXICOLOGICAL INFORMATION
Acute Studies: Test on similar materials show low order of acute oral and dermal toxicity.
Eye Effects: Minimal irritation on contact.
Acute Oral Effects: Test on similar material indicate low order of acute oral toxicity.
12 ECOLOGICAL INFORMATION
No data available.
13 DISPOSAL CONSIDERATIONS
Consult municipal authorites, landfill personnel, disposal companies for details prior to any disposal activity. Always follow
local, state and federal regulations.
14 TRANSPORT INFORMATION
This material is regulated by Department of Transportation (DOT).
Proper Shipping Name: Combustible Liquid N.O.S. UN1993, PGIII
Combustible Warning & Placards required only when packaged in containers holding 119 gallons or more.
Flammable Warning & Placards required only when shipping 1,000 lbs or more by air or water.
15 REGULATORY INFORMATION
This MSDS has been prepared in accordance with federal OSHA Hazard Communication Standard 29 CFR 1910.1200.
HMIS Codes: Health(1) Flammability(2) Reactivity(0) PPE(B)
TSCA (Toxic Substance Control Act) Status:
The international ingredients of this product are listed.
CERCLE RQ - 40 CFR 302.4(a)
Xylene (O-,M-,P-, Isomers) 100 lbs.
SARA 311/312 Hazard Class - 40 CFR 370.2
1,2,4-Trimethylbenzene CAS# 95636 10-20%
Xylene (mixed isomers) CAS# 100414 1.0-2.5%
MSDS Material Safety Data Sheet
UNITEX
K.C. WHITE ACRYLIC CURE 25% (TYPE II) 5 5
Page of
MSDS Number: 2004 Revision Date: Jan. 24, 2004
Cumene CAS# 98828 0.1-1%
OSHA - Not listed
EPA - Not listed
California Proposition 65 - None
Pennsylvania/New Jersey RTK label information
1,2,4-Trimethylbenzene CAS# 95636
Xylenes CAS# 1330207
Cumene CAS# 98828
All components of this product are listed on the Toxic Substance Inventory or are excluded from listing requirements.
16 OTHER INFORMATION
The product has been classified and marked in accordance with directives on hazardous materials.
Risk Phrases:
Flammable.
Irritating to respiratory system.
Harmful: may cause lung damage if swallowed.
Safety Phrases:
Avoid exposure-obtain special instructions before use.
Keep out of reach of children.
Keep container closed until ready to use.
Keep container in a well ventilated place.
Keep away from food, drink and animal feed.
Keep away from sources of ignition - no smoking.
When using do not eat or drink.
Do not empty into drains, dispose of this material and its container at hazardous or special waste collection point. In case of
accident or if you feel unwell, seek medical advice immediately.
Avoid using indoors without ventillation (industrial and professional use only).
This information and recommendations in this document are based on the best information available to us at the time of
preparation. We make no other warranty, expressed or implied, as to its correctness or completeness, or as to the results or
reliance of this product.
END OF MSDS DOCUMENT
|