THERMO-LAG 3000-SP
THERMO-LAG 3000-SA
Application Instructions
This product was formerly known as:
SPRAY EQUIPMENT (SINGLE COMPONENT)
THERMO-LAG 3000 (95% solids) Petro
THERMO-LAG 3000 (95% solids) Arch Must use a 45:1 King, 67:1 Premier or 74: 1 Premier with
a minimum 3/4" outlet on high pressure side. Requires a
PRIMERS AND TOPCOATS hopper feed. Remove all filters and surge tanks. Bottom
ball check should be set at its greater travel.
Use only Carboline approved primers and topcoats.
Existing primers must be pre-approved by Carboline.
SPRAY GUN
REINFORCEMENT Binks 1M Mastic Airless Gun or equivalent
High Temp Mesh or Fiberglass Mesh depending on the Remove fluid tube and replace with gun swivel. Install a
design Graco tip adapter. Gun must have a non-diffuser seat
housing.
STORAGE CONDITIONS
SPRAY TIPS
Store off ground, above 32藲F (0掳C), below 100藲F (38掳C)
Graco Heavy Duty RAC (Gray Key non-diffuser,
and out of direct sunlight.
non-cateye type)
Size: 0.035鈥? to 0.065鈥? revers-a-clean or
Prior to spraying, temperature of must be a minimum of
equal
70掳F (21掳C).
Fan Pattern: 6鈥? to 10鈥?
RAC adapter must be used with Graco spray tips on a
APPLICATION CONDITIONS Binks gun.
Air and substrate temperature:
above 41掳F (5掳C) and rising
HOSES (SOLVENT RESISTANT)
5掳F (3掳C) above dew point
Delivery: 3/4鈥? ID minimum, 50 Ft. maximum
Humidity: not greater than 85%
Whip: 1/2鈥? ID minimum, 20 Ft. maximum
(Provide heat and/or dehumidification if needed.)
MEASURING DEVICES
SURFACE PREPARATION
Hydra-Cone wet film thickness or single bridge gauge
Blast to:
Magnetic dry film thickness gauge (Banana Gauge)
SSPC-SP6 (Sa 2) for Onshore Applications
Positester 6000/Elcometer 345 or equivalent electronic
SSPC-SP10 (Sa 2-1/2) for Offshore Applications
dry film thickness gauge.
Minimum profile - 1.5 to 2.0 mils
Air & Steel Temperature
MIXER
Sling Psychrometer
Standard Static, 12 turn, 3/4鈥? ID
Surface Temperature Thermometer
Milwaukee Power, 1/2" Hole Hawg Drill set at 300 rpm
(electric) with dry wall mud paddle mixer
Safety Equipment
鈥espirators 鈥afety Glasses
THINNER
鈥loves 鈥lastic/Paper Sheeting
Toluene
Must be in compliance with local, state, federal and
project safety standards.
ROLLERS
Solvent resistant foam or Mohair rollers.
Clean Up
Pump, Gun, Tips and Hoses: Toluene, MEK, MIBK,
COMPRESSOR or Xylene
Large enough to run pump and deliver consistent air When flushing pump, remove hopper and bottom foot of
supply pump to clean lower ball check value.
March 2007
To the best of our knowledge the technical data contained herein is true and accurate on the date of publication and is subject to change without prior notice. User must contact Carboline Company to verify
correctness before specifying or ordering. No guarantee of accuracy is given or implied. We guarantee our products to conform to Carboline quality control. We assume no responsibility for coverage,
performance or injuries resulting from use. Liability, if any, is limited to replacement of products. NO OTHER WARRANTY OR GUARANTEE OF ANY KIND IS MADE BY CARBOLINE, EXPRESS OR
IMPLIED, STATUTORY, BY OPERATION OF LAW, OR OTHERWISE, INCLUDING MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Carboline庐 and THERMO-LAG庐 are registered
trademarks of Carboline Company.
|