MATERIAL SAFETY DATA SHEET
SECTION I: PRODUCT IDENTIFICATION
Product Name: Acrylabs 6400 Series Coatings (Liquid Walk Pads)
Chemical Name: Acrylic Coating Solution
Date of Revision: 5/11/2005
SECTION II: COMPANY IDENTIFICATION
Address: Acrylabs, Inc.
730 Commercial Lane
Honey Brook, PA 19344
Emergency Phone Number: (610) 273-1355
Informational Phone Number: 866-273-1355
SECTION III: HAZARDOUS INGREDIENTS
CAS Weight Occupational Exposure Limits Vapor Pressure
Ingredient Regulation # (%) (as Hg @ Temp.)
OSHA PEL ACGIH TLV OSHA STEL
Aromatic Petroleum Distillates 64742-95-6 100 PPM 100 PPM None
Xylene** 1330-20-7 5 100 PPM 100 PPM 150 PPM 5.1 Hg @ 68?F
Zinc Dibutyldithiocarbanate 136-23-2 None None None
Alicyclic Hydrocarbon Resin 69430-35-9 None None None
/Ethylene/Butylene Block Copolymer 66070-58-4 None None None
Pigment Non-hazardous 10 mg/m?10 mg/m? 5 mg/m?br>
Extender Non-hazardous None 5 mg/m? None
**Indicates toxic chemical(s) subject to the reporting requirements of section 313 of title III and of 40 CFR 372.
SECTION IV: PHYSICAL DATA
Boiling Point: 279?F
Vapor Density: N/A
Solubility in Water: Negligible
Appearance and Odor: White or colored medium viscosity liquid
Specific Gravity: 1.3 (water = 1)
Evaporation Rate: N/A
SECTION V: FIRE AND EXPLOSION HAZARD DATA
Flash Point: 106?F
Method Used: Seta Flash
Means of Extinguishing: Foam, alcohol foam, CO2, dry chemical
Unusual Fire and Explosion Hazards: If fire occurs, solvents may produce excessive pressure. Sealed drums may rupture and
ignite. Vapors are heavier than air and may travel along the ground and ignite by any source of ignition. Never use a cutting or
welding torch near containers (even empty).
Special Fire Fighting Procedures: Do not enter confined fire area without full bunker gear, including a positive pressure, NIOSH
approved, self-contained breathing apparatus. Cool all fire-exposed containers with water. Presence of solvents in product may
require grounding.
SECTION VI: HEALTH HAZARD DATA
Threshold Limit Value: Not established.
Effects of Over Exposure (For Product):
Eyes: Can cause severe irritation, redness, tearing or blurred vision.
Skin: May cause irritation, defatting and dermatitis. Not likely to be absorbed in skin in toxic amounts, but measures
should be taken to avoid all contact with this material.
Inhalation: Can cause nausea and respiratory irritation, dizziness, weakness, fatigue, headache and possible
unconsciousness.
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, diarrhea and aspiration of material into the lungs can
cause chemical pneumontitis, which can be fatal.
Health Hazards (Acute and Chronic): Repeated contact to skin may cause defatting or dryness of skin or other
similar conditions. Over-exposure to this material can cause cardiac abnormalities, anemia, liver abnormalities, kidney
damage or even eye damage.
Emergency and First Aid Procedures:
If in Eyes: If this product comes in contact with eyes, flush with large quantities of water for at least 15 minutes lifting
upper and lower lid occasionally. Seek medical attention.
If on Skin: Thoroughly wash exposed area with soap and large quantities of water. Remove contaminated clothing
and launder before reuse. Seek medical attention if irritation from contact persists.
If Inhaled: Remove victim to fresh air area and administer oxygen if necessary.
If Ingested: Do not induce vomiting. Keep person warm and consult a physician immediately.
Carcinogenicity: NTP? No IARC Monographs? No OSHA Regulated? No NPT Program? No
IARC Program? No
Medical Conditions Generally Aggravated by Exposure: Respiratory conditions or other allergic response.
SECTION VII: REACTIVITY DATA
Stability: Stable.
Conditions to Avoid: Avoid excessive heat or open flames, as well as all sources of ignition, such as sparks, heaters, static
discharges, etc.
Incompatibility: Avoid contact with strong oxidizing agents.
Hazardous Decomposition: May form toxic chemicals, carbon dioxide, carbon monoxide and various hydrocarbons.
Hazardous Polymerization: Will not occur.
SECTION VIII: PRECAUTIONS FOR SAFE HANDLING AND USE
Steps to be Taken in Case Material is Released or Spilled:
Wear respirator and protective clothing. Remove all sources of ignition. Remove excess with vacuum truck and take
up the remainder with an absorbent such as clay and place in disposal containers. Flush area with water to remove
residue.
Waste Disposal Method:
Dispose of material in a waste disposal site in accordance with local, state and federal laws.
Precautions to be taken in Handling and Storage:
Store in cool, dry place. Seal all partially used containers. Wash with soap and water before eating, drinking and
smoking or using toilet facilities. Properly label all containers. Keep material away from all sources of ignition.
Other Precautions:
Avoid all skin contact. Avoid breathing vapors generated from the material. Observe conditions of good general
hygiene and safe working practices. Wash all contaminated clothing prior to the reuse thereof. Wear appropriate
safety equipment and respirator at all times when ventilation is not sufficient to control vapors.
SECTION IX: CONTROL MEASURES
Respiratory Protection: Use a NIOSH approved respirator as required to prevent over-exposure to vapor in accordance with 29
CFR 1910.134. Engineering or administrative measures should be taken to reduce the risk and exposure.
Eye Protection: Splash goggles or glasses with side shields.
Ventilation: Provide sufficient mechanical (General) and/or local exhaust ventilation to maintain exposure below TVL(s).
Protective Gloves: Impervious gloves - neoprene or rubber.
Other Protection: Wear body-covering clothing and other coverings as necessary, such as an apron and appropriate footwear to
avoid contact with material.
Work/Hygienic Practices: Observe good general hygienic practices.
Prepared by Acrylabs, Inc.- Technical Department 5/11/05
The information contained herein relates only to the specific material identified and is believed to be accurate and reliable by all
those associated with Acrylabs, Inc. No representations, guarantee or warranty, expressed or implied, is made as to the accuracy,
reliability, or completeness of the information provided. Users assume all risks associated with the use of the material and are
advised to confirm in advance that the information contained in this MSDS is correct, applicable, and suitable to their
circumstances. In accordance with the OSHA Federal Hazard Communication Standard, the actual percentages of ingredients have
been omitted.
|