MATERIAL SAFETY DATA SHEET
ST-100 BASE COMPONENT
Document #3300 Page 1 of 2
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: ITW AMERICAN SAFETY TECHNOLOGIES TRADE NAME: ST-100
565 Eagle Rock Ave. BASE COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: EPOXY
DOT SHIPPING CLASSIFICATION (49 CFR 172.101): (Not Regulated) HMIS RATING:
TRANSPORTATION EMERGENCY NO. (CHEMTREC): 1-800-424-9300 HEALTH =2
MFG'S DUNN'S NO: 002-171-213 FLAMMABILITY=1
REACTIVITY =0
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT NO. OR ORDER NO:
5601-01-366-4776 MIL-D-24613 Type III
PREPARED BY: J. Hermele DATE: 12/11/00 REVISION: 4
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS NO. WT. OSHA ACGIH OTHER
Bisphenol-A Diglycidyl Ether 25068-38-6 35-50% N.E. N.E. LD50RAT>5g/Kg Oral
Aliphatic Monoglycidyl Ether 68609-97-2 15-25% N.E. N.E. LD50RAT>17g/Kg Oral
Zinc Borate 12447-61-9 10-15% 15mg/m3 dust 10mg/m3 dust
Dodecachloro Cyclo Octene 13560-89-9 20-35% N.E. N.E. LD50RAT>25g/Kg Oral
(N.E. = Not Established)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING TOXIC
CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY
PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF 1986 AND OF 40 CFR 372. THIS
INFORMATION MUST BE INCLUDED ON THE MSDS COPIED AND DISTRIBUTED FOR THIS MATERIAL.
CHEMICAL NAME CAS NUMBER WEIGHT %
Zinc Borate 12447-61-9 10-15%
SECTION 3: PHYSICAL DATA
BOILING POINT: >300癋/149癈 SPECIFIC GRAVITY: 1.1
VAPOR PRESSURE: <0.1mmHg @ 68癋/20癈 MELTING POINT: N.E.
VAPOR DENSITY: N.E. (AIR = 1) EVAPORATION RATE: <1.0 (Butyl Acetate = 1)
SOLUBILITY IN WATER: Insoluble
APPEARANCE AND ODOR:Clear Liquid, Mild Odor
SECTION 4: FIRE AND EXPLOSION HAZARD
FLASH POINT: > 200癋/93癈 PMCC FLAMMABLE LIMITS: LEL UEL
N.E. N.E.
EXTINGUISHING MEDIA: Carbon Dioxide, Chemical Foam, Dry Chemical or Water Spray.
SPECIAL FIRE FIGHTING PROCEDURES: Use self-contained breathing apparatus and complete personal
protective equipment where potential for exposure to vapors or products of products of combustion exists.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: Decomposition and combustion products may be toxic.
ST-100 BASE COMPONENT
Page 2 of 2
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin/Ingestion
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Irritant.
Skin: Irritant. May cause allergic skin reaction which can be severe in certain individuals.
Inhalation: May cause nose and throat irritation.
Ingestion: No specific information available. Contains materials that may be slightly toxic.
CONDITIONS AGGRAVATED BY EXPOSURE: Allergy, eczema and other skin conditions.
CARCINOGENIC DATA: Not on NTP, IARC or OSHA lists.
OVEREXPOSURE EFFECTS: Irritation, sensitization and dermatitis.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water for at least 15 minutes. Get medical attention.
Skin: Remove contaminated clothing and wash contact area with mild soap and water.
Inhalation: Remove to fresh air. If breathing is difficult, administer oxygen.
Ingestion: Give large quantities of water to dilute, induce vomiting. Get medical attention.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive Heat
INCOMPATIBILITY (Materials to Avoid): Strong Oxidizing Agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide and Carbon Dioxide.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Dike spill. Absorb with inert
material and collect for disposal. Flush contaminated area with water and collect rinsate for disposal.
WASTE DISPOSAL METHODS: Dispose of in accordance with Federal, State and Local Regulations.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator with organic vapor cartridge if required.
VENTILATION: Mechanical ventilation and local exhaust are recommended. Mechanical exhaust is not
recommended as the sole means of controlling employee exposure.
PROTECTIVE GLOVES: Impervious gloves.
EYE PROTECTION: Chemical splash-proof goggles.
OTHER PROTECTIVE EQUIPMENT: In operations where contact may occur, coveralls, apron and
impervious foot covering are recommended.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid all personal contact. Do not exceed
110癋/43癈 in storage area.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
* A safety shower and eye wash facility should be available to employees.
* Immediately remove and thoroughly launder contaminated clothing before reuse.
MATERIAL SAFETY DATA SHEET
ST-100 HARDENER COMPONENT
Page 1 of 2
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: AMERICAN SAFETY TECHNOLOGIES INC. TRADE NAME: ST-100
565 Eagle Rock Ave. HARDENER COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: Amine Compound
DOT SHIPPING CLASSIFICATION (49 CFR 172.101): Paint,8,UN3066,III HMIS RATING:
TRANSPORTATION EMERGENCY NO. (CHEMTREC): 1-800-424-9300 HEALTH =3
MFG'S DUNN'S NO: 002-171-213 FLAMMABILIT =1
REACTIVITY =1
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT NO. OR ORDER NO:
5601-01-366-4776 MIL-D-24613 Type III
PREPARED BY: J. Hermele DATE: 08/14/98 REVISION: 3
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS NO. % WT. OSHA ACGIH
Polyethylene Polyamine Adduct 68951-85-9 82% N.E. N.E.
Diethylene Triamine (DETA) 111-40-0 8% 1ppmTWA 1ppmTWA
Bisphenol-A 80-05-7 10% N.E. N.E.
(N.E. = Not Established)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING TOXIC CHEMICALS
SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY PLANNING AND
COMMUNITY RIGHT-TO-KNOW ACT OF 1986 AND OF 40 CFR 372. THIS INFORMATION MUST BE INCLUDED
ON THE MSDS COPIED AND DISTRIBUTED FOR THIS MATERIAL.
CHEMICAL NAME CAS NUMBER WEIGHT %
Bisphenol-A 80-05-7 10%
SECTION 3: PHYSICAL DATA
BOILING POINT: N.E. SPECIFIC GRAVITY: 0.98
VAPOR PRESSURE: <1.0mmHg @ 68 F/20 C MELTING POINT: N.E.
VAPOR DENSITY: N.A. (AIR = 1) EVAPORATIONRATE: N.A. (Butyl Acetate = 1)
SOLUBILITY IN WATER: Partially Soluble
APPEARANCE AND ODOR: Clear Amber Liquid, Amine Odor
(N.A. = Not Applicable)
SECTION 4: FIRE AND EXPLOSION HAZARD
FLASH POINT: > 200 F/93癈 SETA FLAMMABLE LIMITS: LEL UEL
N.E. N.E.
EXTINGUISHING MEDIA: Carbon Dioxide or Dry Chemical for small fires; Aqueous Foam or Water for large fires.
SPECIAL FIRE FIGHTING PROCEDURES: Wear self-contained breathing apparatus and complete personal
protective equipment where potential for exposure to vapors of products of combustion exists.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: Closed containers may rupture (due to build up of pressure)
when exposed to extreme heat.
MSDS ST-100 Hardener Component P a ge 2 of 2
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin/Ingestion
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: May cause burns; irreversible damage.
Skin: May cause burns and sensitization. May cause allergic skin reaction, which may be severe in
certain individuals. May be absorbed in harmful amounts.
Inhalation: May cause headache, nausea, dizziness and respiratory tract irritation. Sensitizer; May cause
allergic respiratory reaction.
Ingestion: No specific information available. Contains material that may be slightly toxic.
CONDITIONS AGGRAVATED BY EXPOSURE: Allergy, eczema and other skin conditions.
CARCINOGENIC DATA: Not on NTP, IARC or OSHA lists.
OVEREXPOSURE EFFECTS: Irritation, sensitization and dermatitis.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water for at least 15 minutes. Get medical attention.
Skin: Remove contaminated clothing and wash contact area with mild soap and water.
Inhalation: Remove to fresh air. If breathing has stopped administer artificial respiration and seek medical
attention.
Ingestion: Get immediate medical attention.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: Excessive Heat
INCOMPATIBILITY (Materials to Avoid): Strong Oxidizing Agents.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon Monoxide, Carbon Dioxide and Oxides of Nitrogen.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Dike spill. Absorb with inert material and
collect for disposal. Flush contaminated area with water; prevent washings from entering waterways.
WASTE DISPOSAL METHODS: This product, if disposed as shipped, meets EPA criteria of a hazardous waste as
specified in 40 CFR 261 on the basis of corrosivity. Dispose of in a licensed hazardous waste facility in accordance with
applicable laws.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved respirator with organic vapor cartridge if required.
VENTILATION: Local exhaust recommended. Mechanical ventilation is not recommended as the sole means of
controlling employee exposure.
PROTECTIVE GLOVES: Impervious gloves.
EYE PROTECTION: Chemical splash-proof goggles.
OTHER PROTECTIVE EQUIPMENT: In operations where contact may occur, coveralls, apron and impervious foot
covering are recommended.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Avoid all personal contact. Do not exceed
110 F/43 C in storage area.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
* A safety shower and eye wash facility should be available to employees.
* Immediately remove and thoroughly launder contaminated clothing before reuse.
MATERIAL SAFETY DATA SHEET
T-10/T-100/ST-100 AGGREGATE COMPONENT
Document # 3310___________________________________________________________Page 1 of 2_
SECTION 1: PRODUCT IDENTIFICATION AND USE
MFG'S NAME: ITW AMERICAN SAFETY TECHNOLOGIES TRADE NAME: T-10/T-100/ST-100
565 Eagle Rock Ave. AGGREGATE COMPONENT
Roseland, New Jersey 07068
(973) 403-2600 CHEMICAL FAMILY: N.A.
DOT SHIPPING CLASSIFICATION (49 CFR 172.101): (Not Regulated) HMIS RATING:
TRANSPORTATION EMERGENCY NO. (CHEMTREC): 1-800-424-9300 Health =1
MFG'S DUNN'S NO: 002-171-213 Flammability =0
Reactivity =0
NATIONAL STOCK NO: SPEC: (Type, Grade, or Class) CONTRACT OR ORDER NO
5601-01-366-4776 MIL-D-3135 Type I/II Class 2
MIL-D-3134 Type I Class 2
PREPARED BY: J. Hermele DATE: 12/11/00 REVISION: 5
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
INGREDIENTS CAS NO. % WT. OSHA ACGIH OTHER
Silicon Dioxide 14808-60-7 <35% 8HrTWA 8HrTWA (For Respirable Dust)
(Resin Coated) 0.1mg/m3 0.1mg/m3
Marble (Limestone) 1317-65-3 <35% N.E. N.E. N.E.
Calcium Magnesium Carbonate 16389-88-1 <35% 5mg/m3 N.E.
May contain Varied percentages
Contains <1% Silica-Quartz CAS #14808-60-7 as respirable dust.
(N.E.= Not Established)
SECTION 313 SUPPLIER INFORMATION: THIS PRODUCT CONTAINS THE FOLLOWING TOXIC
CHEMICALS SUBJECT TO THE REPORTING REQUIREMENTS OF SECTION 313 OF THE EMERGENCY
PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT OF 1986 AND OF 40 CFR 372. THIS
INFORMATION MUST BE INCLUDED ON THE MSDS COPIED AND DISTRIBUTED FOR THIS MATERIAL.
CHEMICAL NAME CAS NUMBER WEIGHT %
None
SECTION 3: PHYSICAL DATA
BOILING POINT: N.A. SPECIFIC GRAVITY: 2.7
VAPOR PRESSURE: N.A. MELTING POINT: N.A.
VAPOR DENSITY: N.A. (AIR = 1) EVAPORATION RATE: N.A. (Butyl Acetate = 1)
SOLUBILITY IN WATER: Insoluble
APPEARANCE AND ODOR: Variously colored crushed stone, No Odor.
(N.A. = Not Applicable)
SECTION 4: FIRE AND EXPLOSION HAZARD
FLASH POINT: N.A. FLAMMABLE LIMITS: LEL UEL
N.A. N.A.
EXTINGUISHING MEDIA: N.A. (Can be used to smother fires).
SPECIAL FIRE FIGHTING PROCEDURES: None.
UNUSUAL FIRE AND EXPLOSIVE HAZARDS: None. Material is non-combustible.
SECTION 5: HEALTH HAZARD DATA
PRIMARY ROUTES OF ENTRY: Inhalation/Skin/Ingestion
HEALTH HAZARDS (ACUTE AND CHRONIC)
Eyes: Aggregate may cause injury..
Skin: Aggregate abrasiveness may cause irritation or injury.
T-10/T-100/ST-100 AGGREGATE COMPONENT
Page 2 of 2
SECTION 5: HEALTH HAZARD DATA (Cont'd).
HEALTH HAZARDS (ACUTE AND CHRONIC)
Inhalation: A nuisance particulate with a long history of little adverse effect on lungs, and no
production of significant organic disease or toxic effect when exposures are kept under
reasonable control.
Ingestion: No specific information available. Should not cause any significant health problems.
CONDITIONS AGGRAVATED BY EXPOSURE: Respiratory Diseases.
CARCINOGENIC DATA: This product contains silicon dioxide/silica. The International agency for Research on
Cancer (IARC), concluded that there was "sufficient evidence in humans for the carcinogenicity of crystalline
silica in the forms of quartz or crystabalite from occupational sources." The overall IARC evaluation was that
"crystalline silica inhaled in the form of quartz or crystabalite from occupational sources is carcinogenic to
humans (Group 1). NTP, in its Ninth Annual Report on Carcinogens has classified, "silica, crystalline
(respirable)" to be a carcinogen." Crystalline silica is not regulated by OSHA as a carcinogen. Since all silicon
dioxide/silica is of non-respirable size and encapsulated in the coating, no over exposure to airborne dusts is to
be expected. However, during removal by mechanical abrasion, appropriate safety practices should be followed
to prevent inhalation of airborne dusts.
OVEREXPOSURE EFFECTS: Chronic lung scarring leads to a progressive massive fibrosis that is often
accompanied by susceptibility to pulmonary tuberculosis and other respiratory infections.
EMERGENCY AND FIRST AID PROCEDURES:
Eyes: Flush with large quantities of water to remove particles.
Skin: Wash with mild soap and water.
Inhalation: Remove from exposure.
Ingestion: If large amount is ingested and conscious, give large quantities of water and induce
vomiting. Get medical attention.
SECTION 6: REACTIVITY DATA
STABILITY: Stable
CONDITIONS TO AVOID: None
INCOMPATIBILITY (Materials to Avoid): Acids
HAZARDOUS DECOMPOSITION PRODUCTS: None.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 7: SPILL OR LEAK PROCEDURES
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Use respiratory protection for
airborne dust. Vacuum or scoop for recovery or disposal. Wetting spill with a water spray will help to keep dust
levels down; use good ventilation if possible.
WASTE DISPOSAL METHODS: Not considered a hazardous waste; can be used as a soil sweetener.
SECTION 8: SPECIAL PROTECTION INFORMATION
RESPIRATORY PROTECTION: NIOSH/MSHA approved disposable half-mask for dust/mist if required.
VENTILATION: Local exhaust as appropriate. Mechanical ventilation is recommended.
PROTECTIVE GLOVES: Leather or Rubber gloves.
EYE PROTECTION: Safety glasses or dust-tight goggles.
OTHER PROTECTIVE EQUIPMENT: An eye wash facility should be available in material handing area.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: Use dustless system of storage and
handling. Keep well-ventilated.
SECTION 9: SPECIAL / OTHER INSTRUCTIONS
CALIFORNIA PROPOSITION 65 INFORMATION: WARNING! This product contains a chemical known to the
State of California to cause cancer and birth defects or other reproductive harm. (Silicon Dioxide: Respirable
Particles)
* An eye wash facility should be available in area of material handling.
|