3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
Material Safety Data Sheet
Copyright, 2007, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 11/29/2007
Supercedes Date: 04/23/2007
Document Group: 10-2789-5
Product Use:
Specific Use: Contact Adhesive
Intended Use: Industrial use
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Petroleum Distillates 64742-89-8 10 - 30
Petroleum Distillate 64741-84-0 10 - 30
Acetone 67-64-1 10 - 30
Magnesium Resinate 68611-24-5 7 - 13
Polychloroprene 9010-98-4 7 - 13
Methyl Ethyl Ketone 78-93-3 7 - 13
n-Hexane 110-54-3 5 - 10
Toluene 108-88-3 3- 7
Zinc Oxide 1314-13-2 0.1 - 1
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Grey/green, strong petroleum odor.
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and
_________________________________________________________________________________________________
Page 1 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
flash back. May cause severe eye irritation. May cause target organ effects. Contains a chemical or chemicals which can
cause birth defects or other reproductive harm.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the cornea, and
impaired vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
May be absorbed through skin and cause target organ effects.
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Prolonged or repeated exposure may cause:
Respiratory Effects: Signs/symptoms may include cough, shortness of breath, chest tightness, wheezing, increased heart rate,
bluish colored skin (cyanosis), sputum production, changes in lung function tests, and/or respiratory failure.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Prolonged or repeated exposure may cause:
Ocular Effects: Signs/symptoms may include blurred or significantly impaired vision.
Auditory Effects: Signs/symptoms may include hearing impairment, balance dysfunction and ringing in the ears.
Peripheral Neuropathy: Signs/symptoms may include tingling or numbness of the extremities, incoordination, weakness of
the hands and feet, tremors and muscle atrophy.
Olfactory Effects: Signs/symptoms may include decreased ability to detect odors and/or complete loss of smell.
Neurological Effects: Signs/symptoms may include personality changes, lack of coordination, sensory loss, tingling or
numbness of the extremities, weakness, tremors, and/or changes in blood pressure and heart rate.
_________________________________________________________________________________________________
Page 2 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
404 篊
Autoignition temperature
-4 篎 [Test Method: Closed Cup] [Details: Acetone]
Flash Point
1.0 % volume
Flammable Limits - LEL
12.8 % volume
Flammable Limits - UEL
Class IB Flammable Liquid
OSHA Flammability Classification:
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Extremely
flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-
sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
_________________________________________________________________________________________________
Page 3 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam. An aqueous film
forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or
commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an
absorbent material does not remove a toxic, corrosivity or flammability hazard. Collect as much of the spilled material as possible
using non-sparking tools. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the
area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Collect the resulting residue containing
solution. Place in a metal container approved for transportation by appropriate authorities. Seal the container. Dispose of collected
material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Contents may be under pressure, open carefully. Ground containers securely when transferring contents. Wear low static or properly
grounded shoes. Vapors may ignite explosively. May cause flash fire. Prevent build-up of vapors - open all windows and doors.
Maintain vapor concentrations below recommended exposure limits. Use only with cross-ventilation. Without adequate ventilation,
vapors may settle in low-lying areas. Keep away from heat, sparks, and open flame. Do not smoke or ignite matches, lighters, etc.
Extinguish pilot lights and turn off stoves, ovens and other gas and electric appliances (space and water heaters, furnaces, etc.),
electric motors, and other sources of ignition during adhesive use and until all vapors are gone; i.e., until the odor of vapors at the floor
level has disappeared. Do not use electric light switches. Do not generate static sparks (such as by walking on carpet, etc.). Use the
same precautions in the work area and all connected areas. Be sure that any people in the area follow the precautions. Attach a copy
of the precautions to any other container to which this product may by transferred. Avoid prolonged breathing of vapors. Avoid eye
and skin contact. Keep container closed when not in use. If work area conditions prevent compliance with any of the above
precautions, do not use the product. Keep out of the reach of children. For industrial or professional use only. Not intended for
consumer sale or use.
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container
tightly closed. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide local exhaust ventilation at transfer points. Provide appropriate local exhaust
ventilation on open containers. If exhaust ventilation is not available, use appropriate respiratory protection. Do not use in a confined
area or areas with little or no air movement. Use general dilution ventilation and/or local exhaust ventilation to control airborne
exposures to below Occupational Exposure Limits and/or control mist, vapor, or spray. If ventilation is not adequate, use respiratory
protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
_________________________________________________________________________________________________
Page 4 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber, Polyethylene/Ethylene Vinyl Alcohol.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M
Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
Acetone ACGIH TWA 500 ppm Table A4
Acetone ACGIH STEL 750 ppm Table A4
Acetone OSHA TWA, Vacated 750 ppm
Acetone OSHA TWA 1000 ppm Table Z-1
Acetone OSHA STEL, Vacated 1000 ppm
n-Hexane ACGIH TWA 50 ppm Skin Notation*
n-Hexane OSHA TWA, Vacated 50 ppm Table Z-1A
n-Hexane OSHA TWA 500 ppm Table Z-1A
Methyl Ethyl Ketone ACGIH TWA 200 ppm
Methyl Ethyl Ketone ACGIH STEL 300 ppm
Methyl Ethyl Ketone OSHA TWA 200 ppm Table Z-1A
Methyl Ethyl Ketone OSHA STEL 300 ppm Table Z-1A
Petroleum Distillates CMRG TWA 300 ppm
Toluene ACGIH TWA 20 ppm Table A4
Toluene CMRG STEL 75 ppm Skin Notation*
Toluene OSHA TWA, Vacated 100 ppm
Toluene OSHA STEL, Vacated 150 ppm
Toluene OSHA TWA 200 ppm Table Z-2
Toluene OSHA CEIL 300 ppm Table Z-2
Zinc Oxide ACGIH TWA, respirable 2 mg/m3
Zinc Oxide ACGIH STEL 10 mg/m3
Zinc Oxide OSHA TWA, as fume 5 mg/m3 Table Z-1
Zinc Oxide OSHA TWA, respirable 5 mg/m3 Table Z-1
Zinc Oxide OSHA STEL, Vacated, as 10 mg/m3
fume
Zinc Oxide OSHA TWA, Vacated, as 10 mg/m3
dust
Zinc Oxide OSHA TWA, as total dust 15 mg/m3 Table Z-1
* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
_________________________________________________________________________________________________
Page 5 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Grey/green, strong petroleum odor.
Odor, Color, Grade:
Liquid
General Physical Form:
404 篊
Autoignition temperature
-4 篎 [Test Method: Closed Cup] [Details: Acetone]
Flash Point
1.0 % volume
Flammable Limits - LEL
12.8 % volume
Flammable Limits - UEL
>=56 篊 [Details: Acetone]
Boiling point
0.84 g/ml
Density
2.0 [Ref Std: AIR=1]
Vapor Density
<=185 mmHg [@ 68 篎]
Vapor Pressure
.84 [Ref Std: WATER=1]
Specific Gravity
Not Applicable
pH
Not Applicable
Melting point
Slight (less than 10%)
Solubility in Water
>=2.0 [Ref Std: WATER=1]
Evaporation rate
0.7 lb HAPS/lb solids [Test Method: Calculated]
Hazardous Air Pollutants
490 g/l [Test Method: calculated SCAQMD rule 443.1]
Volatile Organic Compounds
70 - 80 %
Percent volatile
587 g/l [Test Method: calculated SCAQMD rule 443.1]
VOC Less H2O & Exempt Solvents
200 - 450 centipoise [@ 73.4 篎]
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Strong oxidizing agents; Heat; Sparks and/or flames
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Hydrocarbons During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
_________________________________________________________________________________________________
Page 6 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Dispose of completely cured (or polymerized) wastes in a sanitary landfill.
Incinerate uncured product in a permitted hazardous waste incinerator.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable), D035 (Methyl ethyl ketone)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
62-1357-2630-5, 62-1357-2631-3, 62-1357-5530-4, 62-1357-5535-3, 62-1357-6530-3, 62-1357-7530-2, 62-1357-8530-1, 62-1357-
8540-0, 62-1357-9530-0, 62-1357-9531-8, 62-1357-9532-6, 78-8990-0393-9
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
n-Hexane 110-54-3 5 - 10
Toluene 108-88-3 3- 7
Methyl Ethyl Ketone 78-93-3 7 - 13
STATE REGULATIONS
_________________________________________________________________________________________________
Page 7 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
Contact 3M for more information.
CALIFORNIA PROPOSITION 65
Ingredient C.A.S. No. Classification
Toluene 108-88-3 *Developmental Toxin
* WARNING: contains a chemical or chemicals which can cause birth defects or other reproductive harm.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
WHMIS: Hazardous
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 3 Reactivity: 0 Special Hazards: None
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Section 14: ID Number Heading Template 1 was added.
Section 14: ID Number(s) Template 1 was added.
Section 2: Ingredient table was added.
Section 15: EPCRA 313 information was added.
Section 15: EPCRA 313 text was added.
Section 8: Exposure guidelines ingredient information was added.
Section 8: Exposure guidelines legend was added.
Section 8: Exposure guideline note was added.
Section 8: Exposure guidelines data source legend was added.
_________________________________________________________________________________________________
Page 8 of 9
3M MATERIAL SAFETY DATA SHEET 3M(TM) Scotch-Weld(TM) Neoprene High Performance Contact Adhesive 1357 11/29/2007
Section 15: California proposition 65 ingredient information was added.
Section 15: California proposition 65 heading was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 9 of 9
|