MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
Material Safety Data Sheet
Copyright, 2008, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051
MANUFACTURER: 3M
DIVISION: Automotive Aftermarket
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 01/09/2008
Supercedes Date: 06/28/2005
Document Group: 10-5266-1
Product Use:
Intended Use: Adhesive
Specific Use: For use on feathering disc pads.
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
HEXANE 110-54-3 30 - 70
OTHER HEXANE ISOMERS Mixture 30 - 60
BETA-PINENE, ALPHA-PINENE, DIPENTENE, BETA-PHELLANDRENE 68240-09-5 7 - 13
POLYMER
POLYISOPRENE 9003-31-0 7 - 13
GLYCEROL ESTER OF HYDROGENATED ROSIN 65997-13-9 3- 7
CYCLOHEXANE 110-82-7 1- 5
HEPTANES Mixture 1- 5
KAOLIN 1332-58-7 0.5 - 1.50
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Amber color; hexane odor.
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Extremely flammable liquid and vapor. Closed containers exposed to
heat from fire may build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and
_________________________________________________________________________________________________
Page 1 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
flash back. May cause target organ effects. Contains a chemical or chemicals which can cause birth defects or other
reproductive harm.
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Mild Eye Irritation: Signs/symptoms may include redness, pain, and tearing.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Intentional concentration and inhalation may be harmful or fatal.
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Prolonged or repeated exposure may cause:
Respiratory Effects: Signs/symptoms may include cough, shortness of breath, chest tightness, wheezing, increased heart rate,
bluish colored skin (cyanosis), sputum production, changes in lung function tests, and/or respiratory failure.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Prolonged or repeated exposure may cause:
Peripheral Neuropathy: Signs/symptoms may include tingling or numbness of the extremities, incoordination, weakness of
the hands and feet, tremors and muscle atrophy.
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
_________________________________________________________________________________________________
Page 2 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
No Data Available
Autoignition temperature
-10 篎 [Test Method: Tagliabue Closed Cup]
Flash Point
1.2 % volume
Flammable Limits - LEL
6.9 % volume
Flammable Limits - UEL
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Extremely flammable liquid and vapor. Closed containers exposed to heat from fire may
build pressure and explode. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Refer to other sections of this MSDS for information regarding physical and health hazards,
respiratory protection, ventilation, and personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information
on handling and managing the spill. Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up
by qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-
sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to
disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and
could cause flammable gases or vapors in the spill area to burn or explode. Contain spill. For larger spills, cover drains and build
dikes to prevent entry into sewer systems or bodies of water. Cover spill area with a fire-extinguishing foam. An aqueous film
forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or
commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an
absorbent material does not remove a toxic, corrosivity or flammability hazard. Collect as much of the spilled material as possible
using non-sparking tools. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the
area with fresh air. Read and follow safety precautions on the solvent label and MSDS. Collect the resulting residue containing
solution. Place in a metal container approved for transportation by appropriate authorities. Seal the container. Dispose of collected
material as soon as possible.
_________________________________________________________________________________________________
Page 3 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Keep out of the reach of children. Avoid eye contact with vapors, mists, or spray. Avoid skin contact. Avoid breathing of vapors,
mists or spray. Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Avoid
static discharge. Ground containers securely when transferring contents. Wear low static or properly grounded shoes. Keep away
from heat, sparks, open flame, pilot lights and other sources of ignition. Avoid contact with oxidizing agents.
7.2 STORAGE
Keep container in well-ventilated area. Keep container tightly closed. Store away from heat. Store out of direct sunlight. Store away
from acids. Store away from oxidizing agents.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Do not use in a confined area or areas with little or no air movement. Provide appropriate local exhaust ventilation on open
containers. Use with appropriate local exhaust ventilation. Provide appropriate local exhaust for cutting, grinding, sanding or
machining.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Indirect Vented Goggles.
8.2.2 Skin Protection
Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Nitrile Rubber, Polyvinyl Alcohol (PVA).
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges and P95 particulate prefilters.
Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
CYCLOHEXANE ACGIH TWA 100 ppm
CYCLOHEXANE OSHA TWA 300 ppm Table Z-1
HEXANE ACGIH TWA 50 ppm Skin Notation*
HEXANE OSHA TWA, Vacated 50 ppm Table Z-1A
_________________________________________________________________________________________________
Page 4 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
HEXANE OSHA TWA 500 ppm Table Z-1A
HEXANE (ISOMERS OTHER THAN N- ACGIH TWA 500 ppm
HEXANE)
HEXANE (ISOMERS OTHER THAN N- ACGIH STEL 1000 ppm
HEXANE)
* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Amber color; hexane odor.
Odor, Color, Grade:
Liquid
General Physical Form:
No Data Available
Autoignition temperature
-10 篎 [Test Method: Tagliabue Closed Cup]
Flash Point
1.2 % volume
Flammable Limits - LEL
6.9 % volume
Flammable Limits - UEL
148 篎 [Details: Hexane]
Boiling point
2.97 [Ref Std: AIR=1]
Vapor Density
12.6500 mmHg [@ 68 篎]
Vapor Pressure
0.80 [Ref Std: WATER=1]
Specific Gravity
Not Applicable
pH
No Data Available
Melting point
Slight (less than 10%)
Solubility in Water
1.9 [Ref Std: ETHER=1]
Evaporation rate
70 % weight
Volatile Organic Compounds
70 % weight
Percent volatile
560 g/l [Test Method: calculated SCAQMD rule 443.1]
VOC Less H2O & Exempt Solvents
3425.0 centistoke
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Heat; Sparks and/or flames; Strong oxidizing agents
Hazardous Polymerization: Hazardous polymerization will not occur.
_________________________________________________________________________________________________
Page 5 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
Hazardous Decomposition or By-Products
Substance Condition
Formaldehyde Not Specified
Carbon monoxide Not Specified
Carbon dioxide Not Specified
Oxides of Sulfur Not Specified
Toxic Vapor, Gas, Particulate Not Specified
SECTION 11: TOXICOLOGICAL INFORMATION
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product
in a permitted hazardous waste facility.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable), D018 (Benzene)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
41-3701-2183-6, 60-9800-2705-0, 62-4487-2608-3
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
_________________________________________________________________________________________________
Page 6 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
HEXANE 110-54-3 30 - 70
CYCLOHEXANE 110-82-7 1- 5
This material contains a chemical which requires export notification under TSCA Section 12[b]:
Ingredient (Category if applicable) C.A.S. No Regulation Status
CYCLOHEXANE 110-82-7 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 2 Flammability: 3 Reactivity: 0 Special Hazards: None
_________________________________________________________________________________________________
Page 7 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Reason for Reissue: The MSDS has been revised because 3M has adopted the 16-section ANSI/ISO format. The potential hazards
of the product have not changed. We encourage you to reread the MSDS and review the information.
Revision Changes:
Section 1: Product name was modified.
Section 1: Product use information was modified.
Copyright was modified.
Section 3: Potential effects from eye contact was modified.
Section 3: Potential effects from skin contact information was modified.
Section 3: Potential effects from inhalation information was modified.
Section 10: Materials and conditions to avoid physical property was modified.
Section 3: Immediate other hazard(s) was modified.
Section 3: Other health effects information was modified.
Page Heading: Product name was modified.
Section 9: Vapor pressure value was modified.
Section 9: Boiling point information was modified.
Section 5: Flammable limits (UE) information was modified.
Section 5: Flammable limits (LEL) information was modified.
Section 5: Flash point information was modified.
Sections 3 and 9: Odor, color, grade information was modified.
Section 9: Property description for optional properties was modified.
Section 9: Specific gravity information was modified.
Section 9: Flash point information was modified.
Section 9: Flammable limits (LEL) information was modified.
Section 9: Flammable limits (UEL) information was modified.
Section 3: Other health effects information (reproductive hazards) was added.
Section 14: ID Number Heading Template 1 was added.
Section 14: ID Number(s) Template 1 was added.
Section 2: Ingredient table was added.
Section 15: TSCA section 12[b] text was added.
Section 15: EPCRA 313 information was added.
Section 15: EPCRA 313 text was added.
Section 8: Exposure guidelines ingredient information was added.
Section 8: Exposure guidelines legend was added.
Section 8: Exposure guideline note was added.
Section 15: TSCA section 12[b] information was added.
Section 8: Exposure guidelines data source legend was added.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
_________________________________________________________________________________________________
Page 8 of 9
MATERIAL SAFETY DATA SHEET 3M(TM) Feathering Disc Adhesive (Type 2), P.N. 08051 01/09/2008
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 9 of 9
|