MATERIAL SAFETY DATA SHEET FOR INWELD?br>
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME : INWELD CLEANER
PRODUCT IDENTIFIER : CLEANER C101-A
PRODUCT USE : CLEANING COMPOUND
ITEM CODE(S) : CLEANER
FORMULA NAME : C101-A
E-MAIL ADDRESS : SALES@INWELLDCORPORATION.COM
WEB ADDRESS : WWW.INWELDCORPORATION.COM
USA ADDRESS : INWELD CORPORATION USA
3962 PORTLAND ST.
COPLAY, PA 18037
PH (610) 261-1900
FAX (610) 261-0744
PREPARED BY : QUALITY MANAGER
TELEPHONE : (610) 261-1900
EMERGENCY TELEPHONE : (610) 261-1900
PREPARATION DATE : MARCH 01, 2003
OSHA REGULATORY STATUS : REGULATED
WHMIS CLASSIFICATION : B, D2A, A
SECTION 2. COMPOSITION / INFORMATION ON INGREDIENTS
HAZARDOUS INGREDIENTS CAS OSHA PEL ACGIH TLV LD50 SPECIES/ROUTE LC50 SPECIES/ROUTE %WT
STODDARD SOLVENT 8052-41-3 100 ppm 100 ppm >3 g/kg rabbit/dermal >8200 mg/m3 (rat) 10 ?30 %
ISOPROPYL ALCOHOL 67-63-0 400 ppm 400 ppm >12 g/kg rabbit/dermal 12000 ppm/8h (rat) 10 ?30 %
LIQUIFIED PETROLEUM GAS 68476-85-7 1000 ppm 1000 ppm N/Av 57.42% v/v (mice) 10 ?30 %
XYLENE 1330-20-7 100 ppm 100 ppm >3 ml/kg rabbit/dermal 6700 ppm/4h (rat) 10 ?30 %
ACETONE 67-41-1 1000 ppm 750 ppm >20 g/kg rabbit/dermal 16000 ppm/4h (rat) 10 ?30 %
METHYL ISOBUTYL KETONE 108-10-1 100 ppm 50 ppm >20 ml/kg rabbit/dermal 4000 ppm/4h (rat) 5 ?10 %
BUTYL CARBITOL 112-34-5 N/E N/E >2 g/kg rabbit/dermal N/Av 1 - 5%
CARBON DIOXIDE 128-38-9 5000 ppm 5000 ppm N/Av N/Av 1 - 5%
SECTION 3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
CONTENTS EXTREMELY FLAMMABLE AND UNDER PRESSURE. STORE BELOW 120癋 (49癈), OUT OF SUNLIGHT AND
AWAY FROM HEAT SOURCES. DO NOT PUNCTUE OR INCINERATE. AVOID CONTACT WITH SKIN AND EYES. VAPOR
HARMFUL. INTENTIONAL MISUSE BY DELIBERATELY CONCENTRATING AND INHALING THE CONTENTS MAY BE
HARMFUL OR FATAL.
EYE: Liquid or vapors may cause redness, burning, tearing, swelling and/or pain.
SKIN: Frequent or prolonged contact can result in defatting and drying of the skin which may result in skin irritation and dermatitis
(rash).
INGESTION: Due to being an aerosol, product does not lend itself to ingestion. Should ingestion occur, it may cause irritation to
membranes of the mouth, throat and gastrointestinal tract, resulting in vomiting and/or cramps.
INHALATION: Prolonged or repeated overexposure is anesthetic. May cause irritation of the respiratory tract, or acute nervous
system depression characterized by headache, dizziness, staggering gait, or confusion.
EFFECTS OF ACUTE EXPOSURE: N/Av
EFFECTS OF CHRONIC EXPOSURE: N/ Av
OTHER IMPORTANT HAZARDS: N/Av
SUGGESTED HMIS RATING: HEALTH | 1 | FLAMMABILITY | 4 | REACTIVITY | 0 | PERSONAL PROTECTION | B |
EFFECTIVE: MARCH 01, 2003 PAGE 1 OF 5
SECTION 4. FIRST AID MEASURES
INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Seek medical
attention if symptoms persist or if unconscious.
INGESTION: Unlikely due to being in aerosol form. Should actual ingestion occur, do not induce vomiting! Drink a glass of water or
milk to dilute. Call a physician or poison control center immediately. Never give anything by mouth to an unconscious person.
EYE CONTACT: Immediately flush with plenty of clear water for at least 15 minutes. Make sure to flush under the eyelids. Consult a
physician for definitive treatment.
SKIN CONTACT: Remove with soap and water. Continue flushing with water for several minutes. Use skin cream to counter resulting
dryness. Consult a physician if irritation continues or if large skin area is affected.
SECTION 5. FIRE FIGHTING MEASURES
CONDITIONS OF FLAMMABILITY: Heat, sparks, flame, red hot metal.
MEANS OF EXTINCTION: For warehouse and storage conditions, use NFPA Class B extinguishers (CO 2, dry chemical or universal
aqueous film forming foam).
SPECIAL FIRE FIGHTING PROCEDURES: Use water spray to cool fire exposed aerosol containers for containers can rupture
violently from heat developed pressure.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Contents extremely flammable and under pressure. In addition, when liquid or vapor
comes into contact with flames or red hot metal, products of combustion will be created. Firemen should wear self-contained
breathing apparatus.
FLASH POINT / DETERMINATION: Propellant < 0癋 (<-18癈)
UPPER FLAMMABLE LIMIT: 9.5%
LOWER FLAMMABLE LIMIT: 1.8%
AUTO-IGNITION TEMPERATURE: N/Av
HAZARDOUS COMBUSTION PRODUCTS: N/Av
EXPLOSION DATA - SENSITIVITY TO MECHANICAL IMPACT: N/Av
EXPLOSION DATA - SENSITIVITY TO STATIC DISCHARGE: N/Av
SECTION 6. ACCIDENTAL RELEASE MEASURES
LEAK / SPILL RESPONSE: Product is an aerosol, therefore spills and leaks are unlikely. In case of rupture, released content should
be contained as any other solvent spill. Spills from aerosol cans are unlikely and are generally of small volume. Large spills are
therefore not normally considered a problem. In case of actual rupture, avoid breathing vapors and ventilate area well. Remove all
sources of ignition and use non-sparking equipment. Soak up material with inert absorbent and place in safety containers for proper
disposal.
SPECIAL INSTRUCTIONS: Aerosol products represent a limited hazard and will not spill or leak unless ruptured. In case of rupture
contents are generally evacuated from the can rapidly. Area should be ventilated immediately and continuous ventilation provided
until all fumes and vapors have been removed. Aerosol cans should never be incinerated or burned. See Section 13 for disposal
considerations.
SECTION 7. HANDLING AND STORAGE
HANDLING PROCEDURES / EQUIPMENT: Avoid prolonged or repeated skin contact. Avoid breathing vapors.
STORAGE REQUIREMENTS: Store in area below 120癋 (49癈). Do not incinerate (burn) containers. Assure can is in a secure
place to prevent knocking over and accidental rupture. Always replace overcap when not in use. For store of pallet quantities,
compliance with ANSI/NFPA 30B is recommended.
EFFECTIVE: MARCH 01, 2003 PAGE 2 OF 5
SECTION 8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EYE PROTECTION: Safety glasses with side shields are recommended as a minimum for any type of industrial chemical handling.
Where eye contact could occur, chemical splash proof goggles are recommended.
SKIN PROTECTION: For brief contact, no precautions other than clean body-covering clothing should be needed. When prolonged
or repeated contact could occur, use protective clothing such as Sol-Vex?gloves or other clothing impervious to the ingredient listed
in Section 2.
ENGINEERING CONTROLS: General ventilation (typically 10 air changes for hour) should be used. Ventilation rates should be
matched to conditions. Local exhaust ventilation or an enclosed handling system, may be needed to control air contamination below
that of the lowest TLV/PEL rated ingredient from Section 2.
EXPOSURE GUIDELINE LEVELS: Since this product is a mixture, an OSHA or ACGIH exposure value is not available. In
determination of any exposure procedures, protection or testing use the lowest rated ingredient in Section 2.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE : Liquid / Gas
ODOR AND APPEARANCE : Clear colorless liquid with solvent-like odor
ODOR THRESHOLD : N/Av
SPECIFIC GRAVITY (H2O=1) : Below 1.0
VAPOUR PRESSURE (mm HG) : N/Av
VAPOUR DENSITY (AIR=1) : Above 1.0
EVAPORATION RATE (BA=1) : N/Av
BOILING POINT (癋) : Propellant <0癋 (<-18癈)
FREEZING POINT (癋) : N/Av
pH : N/Av
COEFFICIENT OF WATER/OIL
DISTRIBUTION : N/Av
DENSITY : N/Av
SOLUBILITY IN WATER : Insoluble
% VOLATILE BY VOLUME : 93.0% Wt Max
VOC'S : N/Av
SECTION 10. STABILITY AND REACTIVITY
STABILITY: Stable.
CONDITIONS TO AVOID: Heat, sparks, flame, red hot metal.
MATERIALS TO AVOID (INCOMPATIBILITIES): Strong oxidizing materials.
CONDITIONS OF REACTIVITY: N/Av
HAZARDOUS DECOMPOSITION BYPRODUCTS: Oxides of carbon.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 11.TOXICOLOGICAL INFORMATION
LD50: N/Av
LC50: N/Av
ROUTES OF ENTRY: INHALATION[ Y] EYE CONTACT[Y] SKIN CONTACT[Y] SKIN ABSORPTION[Y] INGESTION[N]
EXPOSURE LIMITS: Since this product is a mixture, an OSHA or ACGIH exposure value is not available. In determination of any
exposure procedures, protection or testing use the lowest rated ingredient in Section 2.
IRRITANCY OF PRODUCT: N/Av
SENSITIZATION TO PRODUCT / MEDICAL CONDITIONS AGGRAVATED: N/Av
CARCINOGENICITY: None of the ingredients in this product are listed with IARC, NTP or OSHA as being carcinogenic.
TERATOGENICITY / MUTAGENICITY / REPRODUCTIVE TOXICITY: N/Av
TOXICOLOGICAL DATA: N/Av
EFFECTIVE: MARCH 01, 2003 (PAGE 3 OF 5
SECTION 12. ECOLOGICAL INFORMATION
ENVIRONMENTAL EFFECTS: This product has not been tested for environmental effects.
IMPORTANT ENVIRONMENTAL CHARACTERISTICS: N/Av
AQUATIC TOXICITY: N/Av
SECTION 13. DISPOSAL CONSIDERATIONS
An aerosol container that does not contain a significant amount of liquid would meet the definition of scrap metal (40 CFR
261.1(c)(6), and would be exempt from RCRA regulation under 40 CFR 261.6(a)(3)(iv) if it is to be recycled. If containers are to be
disposed of (not recycled) it must be managed under all applicable RCRA and state regulations.
SECTION 14. TRANSPORTATION INFORMATION
SPECIAL SHIPPING INFORMATION : N/Av
DOT HM-181 SHIPPING INFORMATION
PROPER SHIPPING NAME : Consumer Commodity
HAZARD CLASS OR DIVISION : ORM-D
UN NUMBER : 1950
PACKAGING GROUP : none
LABEL(S) REQUIRED : none
TDG SHIPPING INFORMATION
TDG SHIPPING NAME : Aerosols, Flammable Limited Quantity
TDG CLASSIFICATION : 2.1
UN NUMBER : 1950
PACKING GROUP : none
LABEL(S) REQUIRED : none
NAERG : 126
EMERGENCY TELEPHONE NUMBER : (613) 996-6666
INTERNATIONAL TRANSPORT INFORMATION
PROPER SHIPPING NAME : Consumer Commodity
CLASS OR DIVISION : 9
SUBSIDIARY RISK : none
HAZARDOUS LABEL(S) : Miscellaneous
PACKAGING GROUP : none
UN OR ID NUMBER : ID8000
SECTION 15. REGULATORY INFORMATION
TOXIC SUBSTANCES CONTROL ACT (TSCA): The product on this MSDS, or all of its components, is listed under TSCA.
SARA TITLE III, SECTION 313: The following ingredients are subject to the reporting requirements of section 313 of Title III of the
Superfund and Reauthorization Act of 1986 and 40 CFR Part 372: Xylene (10%), Methyl Isobutyl Ketone (6.8%)
CLEAN AIR ACT (CAA): The following ingredients appear on the List of Hazardous Air Pollutants (HAP ?42 USC 7412, Title I, Part
A, p112): Xylene, Methyl Isobutyl Ketone
CLEAN WATER ACT (CWA):The following ingredients appear on the CWA List of Hazardous Substances (40 CFR 116.4): Xylene
CALIFORNIA PROPOSITION 65: The following ingredients appear on the Proposition 65 list(s): None
CANADIAN WORKPLACE HAZARDOUS MATERIALS INFORMATION SYSTEM (WHMIS): This MSDS has been prepared
according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required
by the CPR.
DOMESTIC SUBSTANCES LIST (DSL): The product on this MSDS, or all of its components, is included in the DSL.
EFFECTIVE: MARCH 01, 2003 PAGE 4 OF 5
SECTION 16. OTHER INFORMATION
N/E Not Established
N/Av Not Available
N/Ap Not Applicable
IARC International Agency for Research on Cancer
ACGIH American Conference of Governmental Industrial Hygienists
NIOSH National Institute for Occupational Health and Safety
TLV-TWA Threshold Limit Values, Time Weighted Average
NAERG North American Emergency Response Guidebook
WHMIS Workplace Hazardous Materials Information System
This MSDS format meets ANSI Z400.1-1998, OSHA 1910.1200 and WHMIS requirements. INWELD Corporation provides the
information contained herein in good faith but makes no representation as to its comprehensiveness or accuracy. This document is
intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product.
Product use and conditions of use are beyond the control of INWELD Corporation. Warranty of materials is limited to test results of
product performance as detailed in certificates of compliance. Interpretation of test results is the responsibility of end-user. No other
warranties, expressed or implied, are made. INWELD Corporation is an ISO 9001:2000 registered company.
ADDITIONAL INFORMATION REPLY FORM ?PLEASE FAX OR EMAIL BACK
PLEASE ADD ME TO YOUR MSDS DATA BASE FOR PRODUCT UPDATES:
NAME TITLE / DEPT
FIRM
ADDRESS
CITY
STATE / PROV ZIP / POSTAL CODE
PHONE FAX
EMAIL
ADDRESS
PLEASE SEND ME INFORMATION ON THE FOLLOWING INWELD?PRODUCTS:
WELDING CHEMICAL PRODUCTS
AUTOMOTIVE, TRUCK & BUS FLEET WASH PRODUCTS
CONSUMER CLEANING PRODUCTS
INDUSTRIAL & INSTITUTIONAL CLEANERS
HVAC CHEMICAL PRODUCTS
EFFECTIVE: MARCH 01, 2003 PAGE 5 OF 5
|