---------------------------------------------------------------------------
SECTION 1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
---------------------------------------------------------------------------
CHEMICAL PRODUCT IDENTIFICATION:
PRODUCT ID . . . . . . . . . . : 101-1A
PRODUCT CLASS . . . . . . . . . : PAINT, SOLVENT BASE
TRADE NAME . . . . . . . . . . : POLYAMIDE EPOXY-TINTABLE WHITE
FORMULA ID . . . . . . . . . . : 101-1A
MSDS PREPARATION DATE . . . . . . : 09/26/2005
MANUFACTURER IDENTIFICATION:
NAME . . . . . . . . . . . . . : INSL-X PRODUCTS CORPORATION
ADDRESS . . . . . . . . . . . . : 308 OLD COUNTY ROAD
EDGEWATER FL 32132
TELEPHONE . . . . . . . . . . . : 386-428-6461
EMERGENCY CONTACT . . . . . . . : CHEMTREC
EMERGENCY TELEPHONE . . . . . . : (800) 424-9300
---------------------------------------------------------------------------
SECTION 2 - COMPOSITION/INFORMATION ON HAZARDOUS INGREDIENTS
---------------------------------------------------------------------------
1
CAS# PROPRIETARY
POLYAMIDE RESIN
PCT BY WT: 25 - 35
EXPOSURE LIMIT:
---------------------------------------------------------------------------
2 TETA
CAS# 112-24-3
TRIETHYLENETETRAMINE
PCT BY WT: L/T .50 VAPOR PRESSURE: .010 MMHG @ 68F
EXPOSURE LIMIT:
LD50: Oral, Rat - 2500 mg/kg
---------------------------------------------------------------------------
3 LT AROMATIC SOLVENT, NAPHTHA
CAS# 64742-95-6
AROMATIC PETROLEUM DISTILLATES
PCT BY WT: .5 - 5 VAPOR PRESSURE: 3.000 MMHG @ 68F
EXPOSURE LIMIT:
ACGIH TLV/TWA: NE
OSHA PEL/TWA: NE
CA PROPOSITION 65: Yes
---------------------------------------------------------------------------
4
CAS# 1330-20-7
XYLENE (MIXED ISOMERS)
PCT BY WT: 10.8450 VAPOR PRESSURE: 5.100 MMHG @ 68F
EXPOSURE LIMIT:
ACGIH TLV/TWA: 100 ppm TWA
ACGIH TLV/STEL: 150 ppm STEL
OSHA PEL/TWA: 100 ppm TWA
LC50: Inhalation (Rat) - 6700 ppm/4H
LD50: Oral (Rat) - 4.3 g/kg
CA PROPOSITION 65: NO
---------------------------------------------------------------------------
5 1-METHOXY-2-PROPANOL
CAS# 107-98-2
PROPYLENE GLYCOL m-METHYL ETHER
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
PCT BY WT: .5 - 5 VAPOR PRESSURE: 8.000 MMHG @ 68F
EXPOSURE LIMIT:
ACGIH TLV/TWA: TWA 100 ppm
ACGIH TLV/STEL: STEL 150 ppm
OSHA PEL/TWA: TWA 100 ppm
OSHA STEL: 150 ppm
LC50: Inhalation (Rat) - >10,000 ppm/4 Hr(s)
LD50: Oral (Rat)- 6040 mg/kg
---------------------------------------------------------------------------
6
CAS# 100-41-4
ETHYLBENZENE
PCT BY WT: 2.7460 VAPOR PRESSURE: 7.000 MMHG @ 68F
EXPOSURE LIMIT:
ACGIH TLV/TWA: TWA 100 ppm
ACGIH TLV/STEL: STEL 25 ppm
OSHA PEL/TWA: TWA 100 ppm
OSHA STEL: 125 ppm
LD50: Oral, Rat - 3500 mg/kg
CA PROPOSITION 65: Yes
---------------------------------------------------------------------------
7
CAS# 13463-67-7
TITANIUM DIOXIDE
PCT BY WT: 35 - 50
EXPOSURE LIMIT:
ACGIH TLV/TWA: 10 mg/cu m(Total Dust) - TWA
OSHA PEL/TWA: 10 mg/cu m(Total Dust) - TWA
LD50: Oral (Rat)- >7500 mg/kg (TiO2)
---------------------------------------------------------------------------
8 HYDROUS KAOLIN
CAS# 1332-58-7
ALUMINUM SILICATE
PCT BY WT: 10 - 15
EXPOSURE LIMIT:
ACGIH TLV/TWA: 2 mg/cu m - TWA
OSHA PEL/TWA: 10 mg/cu m (Total dust) - TWA
---------------------------------------------------------------------------
***************************************************************************
This product contains one or more reported carcinogens or suspected
carcinogens which are noted in Section 3, Hazards Identification,
CARCINOGENICITY.
***************************************************************************
***************************************************************************
This product contains one or more Hazardous Air Pollutants.
***************************************************************************
***************************************************************************
This product contains one or more reported mutagens or suspected
mutagens.
***************************************************************************
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
***************************************************************************
This product contains pigments, which may become a dust nuisance when
removed by abrasive blasting, sanding, or grinding.
***************************************************************************
***************************************************************************
This product contains one or more reported or suspected reproductive
toxins.
***************************************************************************
***************************************************************************
This product contains one or more reported teratogens or suspected
teratogens.
***************************************************************************
---------------------------------------------------------------------------
SECTION 3 - HAZARDS IDENTIFICATION
---------------------------------------------------------------------------
POTENTIAL HEALTH EFFECTS
EYES: May cause eye damage and pain.
SKIN: May irritate skin.
INHALATION: Vapor may cause irritation to nose, throat and respiratory
tract. May cause CNS depression.
INGESTION: Not a likely route of exposure, however, irritation of the
mouth, throat and the gastrointestinal tract may occur.
CNS depression may occur.
SIGNS AND SYMPTOMS: Skin sensitization (allergy) may be evidenced by
rashes, especially hives. Early to moderate CNS depression
may be evidenced by giddiness, headache, dizziness and
nausea; in extreme cases, unconsciousness, respiratory
depression and death may occur.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE
Any pre-existing respiratory or eye/skin conditions.
CHRONIC EFFECTS
NOTICE: Reports have associated repeated and prolonged occupational
exposure to solvents with permanent brain and nervous system damage.
Intentional misuse by deliberately concentrating and inhaling the contents
may be harmful or fatal. May cause respiratory and/or skin sensitization.
CARCINOGENICITY
Ethylbenzene has been shown to cause cancer in laboratory animals.
The relevance of this finding to humans is uncertain. IARC has
classified ethylbenzene as a possible human carcinogen, Group 2B.
---------------------------------------------------------------------------
SECTION 4 - FIRST AID MEASURES
---------------------------------------------------------------------------
EMERGENCY FIRST AID:
EYE CONTACT: Flush at once with large amounts of lukewarm water for at
least 15 minutes and get medical attention.
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
SKIN CONTACT: Immediately remove contaminated clothing, wipe excess from
skin and flush with clean water for at least 15 minutes.
Wash affected area with soap and water. Get medical
attention if persistent irritation and/or a skin rash,
appears. Do not reuse clothing until thoroughly cleaned.
INHALATION: Remove victim to fresh air and provide oxygen if breathing is
difficult. Give artificial respiration if not breathing.
Get medical attention.
INGESTION: DO NOT INDUCE VOMITING. Give 1 to 2 cups of milk or water to
drink. Do not give anything by mouth to an unconscious or
convulsing person. Consult a physician.
NOTE TO PHYSICIAN:
Not Applicable.
---------------------------------------------------------------------------
SECTION 5 - FIRE FIGHTING MEASURES
---------------------------------------------------------------------------
FIRE AND EXPLOSIVE PROPERTIES OF THE CHEMICAL:
Flammability Classification . . . . . : 1C
Flashpoint . . . . . . . . . . . . . : 80.0 癋
Explosion Level . . . . . . . . . . . : Low - .9
High - 10.9
EXTINGUISHING MEDIA
Water spray, dry chemical, carbon dioxide (CO2), alcohol foam
FIRE-FIGHTING PROCEDURES AND EQUIPMENT
Clear fire area of unprotected personnel. Do not enter confined space
without helmet, face shield, bunker coat, gloves, rubber boots, and a
positive pressure NIOSH-approved self-contained breathing apparatus.
Water spray may be used to cool closed containers to prevent pressure
build-up and possible explosion when exposed to extreme heat. Water
may be ineffective in extinguishing a paint fire. Therefore, use
caution not to spread flames with stream of water. If water is used,
fog nozzles are preferable.
UNUSUAL FIRE AND EXPLOSION HAZARDS
Delayed lung damage (pulmonary edema) can be experienced after exposure
to combustion products, sometimes hours after the exposure. Nitrogen
oxides and nitrogen containing organic compounds may be released upon
combustion. Containers exposed to intense heat from fires should be
cooled with water to prevent vapor pressure buildup which could result
in container rupture. Container areas exposed to direct flame contact
should be cooled with large quantities of water as needed to prevent
weakening of container structure.
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
---------------------------------------------------------------------------
SECTION 6 - ACCIDENTAL RELEASE MEASURES
---------------------------------------------------------------------------
CLEAN-UP:
Soak up residue with an absorbent such as clay, sand or other suitable
material; place in non-leaking containers for proper disposal. Flush
area with water to remove trace residue; dispose of flush solutions.
*** SMALL SPILLS ***
Take up with an absorbent material and place in non-leaking containers;
seal tightly for proper disposal.
SPILL OR LEAK PROCEDURES:
WARNING! FLAMMABLE. Eliminate all ignition sources. Equipment
must be grounded to prevent sparking.
*** LARGE SPILLS ***
Evacuate the hazard area of unprotected personnel. Wear appropriate
respirator and protective clothing. Shut off source of leak only if
safe to do so. Dike and contain. If vapor cloud forms, water fog may
be used to suppress; contain run-off.
---------------------------------------------------------------------------
SECTION 7 - HANDLING AND STORAGE
---------------------------------------------------------------------------
HANDLING
WARNING: Extremely irritating to the eyes. May cause skin and
respiratory tract irritation. May cause skin sensitization. May
cause CNS depression. Containers, even those that have been emptied,
can contain hazardous product residues.
STORAGE
Store in tightly closed, properly vented containers in a cool, dry
place. Do not puncture containers or expose product to moisture.
SPECIAL COMMENTS
Avoid all bodily contact. Wash with soap and water before eating,
drinking, smoking, or using toilet facilities. Launder contaminated
clothing before reuse. Contaminated leather shoes cannot be
decontaminated and should be destroyed to prevent reuse.
---------------------------------------------------------------------------
SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION
---------------------------------------------------------------------------
ADDITIONAL PROTECTIVE MEASURES
Use explosion-proof ventilation as required to control vapor
concentrations. Eye wash fountains and safety showers should be
available for emergency use.
RESPIRATORY PROTECTION
Avoid breathing dust/mists. If exposure may or does exceed occupational
exposure limits, use a NIOSH-approved respirator to prevent overexposure.
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
Avoid breathing vapors, which may be produced under some conditions such
as heating or applications of uncured product in large surface areas
(e.g., flooring and painting). Avoid breathing aerosols and mists which
may be formed by various methods of application.
EYE PROTECTION
To prevent eye contact wear eye protection such as chemical splash
proof goggles or face shield.
SKIN PROTECTION REQUIREMENTS
Permeation resistant gloves. Cover as much of the exposed skin area
as possible with appropriate clothing, such as, long sleeved clothing,
etc.
---------------------------------------------------------------------------
SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES
---------------------------------------------------------------------------
Physical State . . . . . . . . . . . .: LIQUID
Vapor Pressure . . . . . . . . . . . : 8.00
Vapor Density . . . . . . . . . . . . : 5.00
Boiling Point Range . . . . . . . . . : Lower - 246.0 癋
Higher - 531.0 癋
Specific Gravity . . . . . . . . . . : 1.489
Weight per Volume . . . . . . . . . . : 12.3967 LB/GL
VOC - Total (lbs./gal). . . . . . . . : 2.838
Evaporation Rate . . . . . . . . . . .: .900 (n-Butyl Acetate = 1)
Volatile by Weight . . . . . . . . . : 22.8907
Volatile by Volume . . . . . . . . . : 38.7552
---------------------------------------------------------------------------
SECTION 10 - STABILITY AND REACTIVITY
---------------------------------------------------------------------------
INCOMPATIBILITIES (Materials to Avoid)
This product can react violently with strong oxidizing agents and
strong acids.
HAZARDOUS POLYMERIZATION
Will not occur.
CONDITIONS TO AVOID
Avoid heat and any source of ignition.
HAZARDOUS DECOMPOSITION PRODUCTS
Nitrogen oxides, carbon monoxide and unidentified organic compounds
(some containing nitrogen) may be formed during thermal or oxidative
decomposition of combustion.
STABILITY: Stable.
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
---------------------------------------------------------------------------
SECTION 11 - TOXICOLOGICAL INFORMATION
---------------------------------------------------------------------------
No data at this time.
---------------------------------------------------------------------------
SECTION 12 - ECOLOGICAL INFORMATION
---------------------------------------------------------------------------
No data at this time.
---------------------------------------------------------------------------
SECTION 13 - DISPOSAL CONSIDERATIONS
---------------------------------------------------------------------------
WASTE DISPOSAL
Discharge, treatment, or disposal may be subject to national, state
or local laws. We recommend that organic materials classified as RCRA
hazardous wastes be disposed of by thermal treatment or incineration at
EPA approved facilities.
---------------------------------------------------------------------------
SECTION 14 - TRANSPORT INFORMATION
---------------------------------------------------------------------------
DOT HAZARD CLASS . . . . . . . . : 3
DOT PACKAGING GROUP . . . . . . . : PG III
DOT LABEL . . . . . . . . . . . . : FLAMMABLE LIQUID
DOT SHIPPING NAME . . . . . . . . : PAINT
DOT PLACARD . . . . . . . . . . . : FLAMMABLE LIQUID
UN/NA NUMBER . . . . . . . . . . .: UN1263
---------------------------------------------------------------------------
SECTION 15 - REGULATORY INFORMATION
---------------------------------------------------------------------------
U.S. FEDERAL REGULATORY INFORMATION
TSCA SECTION 8(b) - INVENTORY STATUS:
All components of this product are either listed on the U.S. Toxic
Substances Control Act (TSCA) inventory of chemicals or are otherwise
compliant with TSCA Regulations.
SARA 313 TOXIC CHEMICALS:
This product contains the following substances subject to the
reporting requirements of Section 313 of Title III of the Superfund
Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:
XYLENE (MIXED ISOMERS)
CAS# 1330-20-7 PCT BY WT: 10.8450
---------------------------------------------------------------------------
1,2,4-TRIMETHYLBENZENE
CAS# 95-63-6 PCT BY WT: 2.0330
---------------------------------------------------------------------------
---------------------------------------------------------------------------
INSL-X PRODUCTS CORPORATION
MATERIAL SAFETY DATA SHEET
101-1A 1
---------------------------------------------------------------------------
ETHYLBENZENE
CAS# 100-41-4 PCT BY WT: 2.7460
---------------------------------------------------------------------------
---------------------------------------------------------------------------
SECTION 16 - OTHER INFORMATION
---------------------------------------------------------------------------
Prepared by . . . . . . . . . . . . . :
Date of issue . . . . . . . . . . . . : 09/26/2005
Last Revision Date . . . . . . . . . : 05/21/2002
MSDS Prepared for . . . . . . . . . . :
MSDS Last Prepared . . . . . . . . . : NONE
HMIS Rating: Health- 3 Flammability- 3
Reactivity- 0
***************************************************************************
This Material Safety Data Sheet conforms to the Hazard Communication
Standard, 29 CFR 1910.1200(g)(4).
The above information pertains to this product as currently formulated
and is based on the information available, as of this date. Addition of
reducers or other additives to this product may substantially alter the
composition and hazards of the product. Since conditions of use are out-
side our control, we make no warranties, express or implied, and assume
no liability in connection with any use of this information.
***************************************************************************
Abbreviations used: int.- interior; ext.- exterior; MSDS - Material Safety
Data Sheet; HMIS - Hazardous Materials Information System; CAS - Chemical
Abstracts Services; pct - percent; wt - weight; mm Hg - millimeters of
mercury; F - Fahrenheit; ACGIH - American Conference of Governmental
Industrial Hygienists; TLV - Threshold Limit Value; OSHA - Occupational
Safety and Health Administration; PEL - Permissible Exposure Limit; TWA -
Time-Weighted Average; STEL- Short Term Exposure Limit; N/A- Not applicable
IARC - International Agency for Research on Cancer; NE - Not established
NTP - National Toxicological Program; CFR - Code of Federal Regulations;
OSHA - Z 29CFR 1910, Subpart Z; VOC - Volatile Organic Compounds; TCC -
Tag Closed Cup; LEL - Lower Explosive Limit; Mg/m3 or Mg/Cu M - milligram
per cubic meter; mppcf - millions of particles per cubic foot; ppm - parts
per million; NIOSH - National Institute of Occupational Safety and Health;
MSHA - Mine Safety and Health Administration; CNS - Central Nervous System.
|