View Section :
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
Product Name: RUBBER CEMENT
HMIS
14900
Stock No.:
Manufacturer Name: ITW Devcon
Address: 30 Endicott Street
Health Hazard 2*
Danvers, MA 01923
Fire Hazard 3
MSDS Revision Date: 10/10/2006
REACTIVITY 0
Emergency telephone number (800) 424-9300
Personal
X
Protection
* Chronic Health
Effects:
In the US, call CHEMTREC: (800) 424-9300
To Top of page
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Chemical Name CAS#
Non-hazardous ingredients. N/A 5 - 10 by Weight
Toluene 108-88-3 30 - 60 by Weight
Trade secret. N/A 1 - 5 by Weight
Methyl ethyl ketone 78-93-3 1 - 5 by Weight
Hexane 110-54-3 5 - 10 by Weight
Methylcyclopentane 96-37-7 1 - 5 by Weight
To Top of page
SECTION 3: HAZARDS IDENTIFICATION
Emergency Overview: DANGER! Extremely Flammable. Irritant.
Primary Routes of Exposure: Eyes. Skin. Inhalation. Ingestion.
Potential Health Effects:
Eye Contact: Can cause moderate irritation, burning sensation, tearing, redness, and swelling.
Overexposure may cause lacrimation, conjunctivitis, corneal damage and
permanent injury.
Skin Contact: Can cause skin irritation; itching, redness, rashes, hives, burning, and swelling.
Inhalation: Respiratory tract irritant. High concentration may cause dizziness, headache, and
anesthetic effects.
Ingestion: Causes irritation, a burning sensation of the mouth, throat and gastrointestinal
tract and abdominal pain.
Chronic Health Effects: Prolonged skin contact may lead to burning associated with severe reddening,
swelling, and possible tissue destruction
Signs/Symptoms: Overexposure can cause headaches, dizziness, nausea, and vomiting.
Target Organs: Eyes. Skin. Respiratory system. Digestive system. Central nervous system.
Aggravation of Pre-Existing Individuals with pre-existing skin disorders, asthma, allergies or known
Conditions: sensitization may be more susceptible to the effects of this product.
To Top of page
SECTION 4: FIRST AID MEASURES
Eye Contact: Immediately flush eyes with plenty of water for at least 15 to 20 minutes. Ensure
adequate flushing of the eyes by separating the eyelids with fingers. Get
immediate medical attention.
Skin Contact: Immediately wash skin with plenty of soap and water for 15 to 20 minutes, while
removing contaminated clothing and shoes. Get medical attention if irritation
develops or persists.
Inhalation: If inhaled, remove to fresh air. If not breathing, give artificial respiration or give
oxygen by trained personnel. Seek immediate medical attention.
Ingestion: If swallowed, do NOT induce vomiting. Call a physician or poison control center
immediately. Never give anything by mouth to an unconscious person.
Other First Aid: Due to possible aspiration into the lungs, DO NOT induce vomiting if ingested.
Provide a glass of water to dilute the material in the stomach. If vomiting occurs
naturally, have the person lean forward to reduce the risk of aspiration.
To Top of page
SECTION 5: FIRE FIGHTING MEASURES
Flammable Properties : Extremely Flammable.
Auto Ignition Temp : Not determined.
Flash Point: -9癋 (-22.7癈)
Flash Point Method: Setaflash Closed Cup
Lower Explosive Limit (LEL) 1.0 % (Estimated)
Upper Explosive Limit (UEL) 8.5 % (Estimated)
Extinguishing Media: Use carbon dioxide (CO2) or dry chemical when fighting fires involving this
material.
Protective Equipment: As in any fire, wear self-contained breathing apparatus pressure-demand,
MSHA/NIOSH (approved or equivalent) and full protective gear.
Fire Fighting Instructions: Evacuate area of unprotected personnel. Use cold water spray to cool fire
exposed containers to minimize risk of rupture. Do not enter confined fire space
without full protective gear. If possible, contain fire run-off water.
To Top of page
SECTION 6: ACCIDENTAL RELEASE MEASURES
Personal Precautions: Evacuate area and keep unnecessary and unprotected personnel from entering
the spill area.
Spill Cleanup Measures: Absorb spill with inert material (e,g., dry sand or earth), then place in a chemical
waste container. Provide ventilation. Collect spill with a non-sparking tool. Place
into a suitable container for disposal. Clean up spills immediately observing
precautions in the protective equipment section. After removal, flush spill area
with soap and water to remove trace residue.
Flammable, eliminate ignition sources. Vapors can form an ignitable mixture with
air. Vapors can flow along surfaces to distant ignition sources and flash back.
Ventilate area. Use proper personal protective equipment as listed in section 8.
Environmental Precautions: Avoid runoff into storm sewers, ditches, and waterways.
Other Precautions: Pump or shovel to storage/salvage vessels.
To Top of page
SECTION 7: HANDLING AND STORAGE
Handling: Use with adequate ventilation. Avoid breathing vapor, aerosol or mist. Material
will accumulate static charges which may cause an electrical spark (ignition
source). Use proper grounding procedures. Do not reuse containers without
proper cleaning or reconditioning.
Storage: Store in a cool, dry, well ventilated area away from sources of heat, combustible
materials, direct sunlight, and incompatible substances. Keep container tightly
closed when not in use.
Hygiene Practices: Wash thoroughly after handling.
Special Handling Procedures: Hazardous liquid or vapor residue may remain in emptied container. Do not
reuse, heat, burn, pressurize, cut, weld, braze, solder, drill, grind, expose to
sparks, flame, or ignition sources of empty containers without proper commercial
cleaning or reconditioning.
To Top of page
SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION
Engineering Controls: Use appropriate engineering control such as process enclosures, local exhaust
ventilation, or other engineering controls to control airborne levels below
recommended exposure limits. Good general ventilation should be sufficient to
control airborne levels. Where such systems are not effective wear suitable
personal protective equipment, which performs satisfactorily and meets OSHA or
other recognized standards. Consult with local procedures for selection, training,
inspection and maintenance of the personal protective equipment.
Skin Protection Description: Wear appropriate protective gloves and other protective apparel to prevent skin
contact. Consult manufacturer's data for permeability data.
Eye/Face Protection: Wear appropriate protective glasses or splash goggles as described by 29 CFR
1910.133, OSHA eye and face protection regulation, or the European standard
EN 166.
Respiratory Protection: A NIOSH approved air-purifying respirator with an organic vapor cartridge or
canister may be permissible under certain circumstances where airborne
concentrations are expected to exceed exposure limits. Protection provided by
air purifying respirators is limited. Use a positive pressure air supplied respirator
if there is any potential for an uncontrolled release, exposure levels are not
known, or any other circumstances where air purifying respirators may not
provide adequate protection.
Other Protective: Facilities storing or utilizing this material should be equipped with an eyewash
and a deluge shower safety station.
Toluene:
Guideline ACGIH : ACGIH TLV-TWA 50 ppm
Guideline OSHA : OSHA PEL-STEL 500 ppm Ceiling/Peak
Methyl ethyl ketone:
Guideline ACGIH : ACGIH TLV-STEL 300 ppm
Guideline OSHA : OSHA PEL-TWA 200 ppm
Hexane:
Guideline ACGIH : ACGIH TLV-TWA 50 ppm
Guideline OSHA : OSHA PEL-TWA 500 ppm
Notes : Only established PEL and TLV values for the ingredients are listed below.
To Top of page
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Physical State/Appearance: Liquid.
Color: Syrupy amber
Odor: Hydrocarbon.
Boiling Point: 149-231癋 (65-110.5癈)
Melting / Freezing Point : Not determined.
Solubility: negligible
Specific Gravity: 0.9
pH: 7 @ 5 Percent Solution
Vapor Density: >1 (air = 1)
Vapor Pressure: Not determined.
Molecular Formula: Mixture
Molecular Weight: Mixture
Percent Volatile: 83
VOC Data : 673 g/L
Percent Solids by Weight 17
To Top of page
SECTION 10: STABILITY AND REACTIVITY
Chemical Stability: Stable under normal temperatures and pressures.
Conditions to Avoid: Extreme heat, sparks, and open flame. Incompatible materials, oxidizers and
oxidizing conditions.
Incompatibilities with Other Oxidizing agents. Strong acids and alkalis.
Materials:
Hazardous Polymerization: Not reported.
To Top of page
SECTION 11: TOXICOLOGICAL INFORMATION
Toluene:
Eye Effect: Eye - Human Standard Draize Test : 300 ppm(RTECS)
Skin Effects: Skin - Rabbit Standard Draize Test : 20 mg/24H - [Moderate](RTECS)
Skin - Rabbit LD50: 14100 uL/kg - [Details of toxic effects not reported other
than lethal dose value ](RTECS)
Inhalation Effects: Inhalation - Rat LC50: 49 gm/m3/4H - [Details of toxic effects not reported other
than lethal dose value] (RTECS)
Inhalation - Mouse LC50: 400 ppm/24H - [Details of toxic effects not reported
other than lethal dose value] (RTECS)
Inhalation - Mouse LC50: 30000 mg/m3/2H - [Details of toxic effects not
reported other than lethal dose value] (RTECS)
Inhalation - Mouse LC50: 19900 mg/m3/7H - [Details of toxic effects not
reported other than lethal dose value] (RTECS)
Inhalation - Mouse LC50: 10000 mg/m3 - [Behavioral - somnolence (general
depressed activity) ] (RTECS)
Ingestion Effects: Oral - Rat LD50: 636 mg/kg - [Details of toxic effects not reported other than
lethal dose value ] (RTECS)
Methyl ethyl ketone:
Eye Effect: Eye - Human Standard Draize Test : 350 ppm(RTECS)
Skin Effects: Skin - Rabbit Open irritation test: 14 mg/24H - [mild ](RTECS)
Skin - Rabbit LD50: 6480 mg/kg - [Details of toxic effects not reported other
than lethal dose value ](RTECS)
Inhalation Effects: Inhalation - Rat LC50: 23500 mg/m3/8H - [Details of toxic effects not reported
other than lethal dose value] (RTECS)
Inhalation - Mouse LC50: 32 gm/m3/4H - [Details of toxic effects not reported
other than lethal dose value] (RTECS)
Ingestion Effects: Oral - Rat LD50: 2737 mg/kg - [Details of toxic effects not reported other than
lethal dose value ] (RTECS)
Oral - Mouse LD50: 3000 mg/kg - [Details of toxic effects not reported other
than lethal dose value ] (RTECS)
Hexane:
Eye Effect: Eye - Rabbit Standard Draize Test : 10 mg - [mild ](RTECS)
Inhalation Effects: Inhalation - Rat LC50: 627000 mg/m3/3M - [Details of toxic effects not reported
other than lethal dose value] (RTECS)
Inhalation - Mouse LC50: 150000 mg/m3/2H - [Details of toxic effects not
reported other than lethal dose value] (RTECS)
Ingestion Effects: Oral - Rat LD50: 25 gm/kg - [Details of toxic effects not reported other than
lethal dose value ] (RTECS)
Methylcyclopentane:
Inhalation Effects: Inhalation - Mouse LCLo: 95000 mg/m3 - [Behavioral - general anesthetic
Behavioral - tetany] (RTECS)
To Top of page
SECTION 12: ECOLOGICAL INFORMATION
Ecotoxicity: No ecotoxicity data was found for the product.
Environmental Fate: No environmental information found for this product.
To Top of page
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal: Consult with the US EPA Guidelines listed in 40 CFR Part 261.3 for the
classifications of hazardous waste prior to disposal. Furthermore, consult with
your state and local waste requirements or guidelines, if applicable, to ensure
compliance. Arrange disposal in accordance to the EPA and/or state and local
guidelines.
RCRA Number : D001, D035
Important Disposal Information: DANGER! Rags, steel wool and waste soaked with this product may
spontaneously catch fire if improperly discarded or stored. To avoid a
spontaneous combustion fire, immediately after use, place rags, steel wool or
waste in a sealed, water-filled, metal con
To Top of page
SECTION 14: TRANSPORT INFORMATION
DOT Shipping Name: Adhesives
DOT UN Number: 1133
DOT Hazard Class: 3
DOT Packing Group: II
To Top of page
SECTION 15: REGULATORY INFORMATION
WHMIS Pictograms
Toluene:
State: Listed in the State of Massachusetts Hazardous Substance List.
Listed in the New Jersey State Right to Know List.
Listed in the Pennsylvania State Hazardous Substances List.
EC Num : 601-021-00-3
Methyl ethyl ketone:
State: Listed in the State of Massachusetts Hazardous Substance List.
Listed in the New Jersey State Right to Know List.
Listed in the Pennsylvania State Hazardous Substances List.
EC Num : 606-002-00-3
Hexane:
State: Listed in the State of Massachusetts Hazardous Substance List.
Listed in the New Jersey State Right to Know List.
Listed in the Pennsylvania State Hazardous Substances List.
EC Num : 601-037-00-0
Methylcyclopentane:
State: Listed in the State of Massachusetts Hazardous Substance List.
Listed in the Pennsylvania State Hazardous Substances List.
Canadian Regulations. WHMIS Hazard Class(es): B2; D2B; D2A
All components of this product are on the Canadian Domestic Substances List.
To Top of page
SECTION 16: ADDITIONAL INFORMATION
HMIS Health Hazard: 2*
HMIS Fire Hazard: 3
HMIS Reactivity: 0
HMIS Personal Protection: X
MSDS Revision Date: 10/10/2006
Disclaimer: "This Health and Safety Information is correct to the best of our knowledge and
belief at the date of its publication but we cannot accept liability for any loss,
injury or damage which may result from its use. The information given in the
Data Sheet is designed only as a guidance for safe handling, storage and the use
of the substance. It is not a specification nor does it guarantee any specific
properties. All chemicals should be handled only by competent personnel, within
a controlled environment."
Copyright?1996-2007 Actio Software Corporation. All Rights Reserved.
|