1/4
Printight KF-G, KM-G, KA-G, KM-A Type
First issue: June 10, 2004
Revised: February.23, 2007
MSDS No.F0509K
Material Safety Data Sheet
1. PRODUCT AND COMPANY IDENTIFICATION
Printight KF-G, KM-G, KA-G, KM-A Type
Product Name
SUPPLIER
Name TOYOBO Co., Ltd.
Address Photo Functional Materials Dept., 2-8 Dojima Hama 2-chome, Kita-Ku
OSAKA 530-8230 JAPAN
Telephone No. +81-6-6348-3059
Fax No. +81-6-6348-3099
2 COMPOSITION, INFORMATION ON INGREDIENTS
Chemical Product Preparation
Chemical Name Laminated sheet containing water soluble photo-sensitive resin
Composition Generic Name Concentration
Polyamide 55%
Derivative of Acrylates and Methacrylates 40%
Plasticizer 3%
Photo-initiator and other additives 2%
Components Contributing Product contains following chemical substances;
to the Hazard
-caprolactam
Chemical Name Methyl alcohol Methyl acrylate Methyl methacrylate
Synonyms Methanol
2-azacycloheptanone Methyl 2-propenoate Methy 2-methyl -2-propenoate
Concentration 2.0% or less 3.0% or less 4900ppm or less 2000ppm or less
CHNO CHOH
Chemical Formula CH=CHCOOCH CH=C(CH)COOCH
CAS No. 105-60-2 67-56-1 96-33-3 80-62-6
3 HAZARDS IDENTIFICATION
Most Important Hazards Eye contact or skin contact with the material may cause some irritation.
Dermatitis may occur in some serious case.
The material contains small amount of hazardous ingredients
or the ingredients of insufficient investigation of hazards.
Inflammable with the existence of ignition sources
Specific Hazards Prolonged inhalation of fumes or gases generated from the material
during the processing operations may cause headache, respiratory irritation.
Main Symptoms Dizziness, Headache, Irritation to eyes and skin
4 FIRST-AID MEASURES
Inhalation In case of irritation by inhaling fumes or gases generated from the material
during the processing operations, remove victim to fresh air and await recovery.
Seek immediate medical attention if irritation persists.
Skin Contact If the material or wash-out solution contacts the skin,
wash the affected area thoroughly with water and soap.
Seek medical attention if necessary.
Eye Contact If some irritation is felt in eyes or wash-out solution enters the eyes,
immediately flush eyes with plenty of clean water for at least 15 minutes.
Seek medical attention if irritation persists.
Ingestion If the material or wash-out solution is swallowed, induce vomiting.
Seek immediate medical attention if indisposition persists.
2/4
Printight KF-G, KM-G, KA-G, KM-A Type
First issue: June 10, 2004
Revised: February.23, 2007
MSDS No.F0509K
Material Safety Data Sheet
5 FIRE-FIGHTING MEASURES
Extinguishing Media Carbon Dioxide, Water-Spray, Dry Chemical, Foam
Specific Hazards When subjected to prolonged high temperature or burning, this
product will emit harmful gas containing carbon monoxide, nitrogen oxides,
chlorine compounds and sulfur oxides.
Specific Methods Extinguish the fire from windward by water or carbon dioxide.
Protection of Firefighters Wear self-contained breathing apparatus and protective clothing.
6 ACCIDENTAL RELEASE MEASURES
Personal Precautions The unexposed and exposed plates are solid and considered low
hazard material to human body. If the material contacts the body,
wash the affected area thoroughly with water and soap.
Wash-out solution remained on the skin may cause some irritation.
Environmental Precautions The unexposed plate is soluble in water, that may pollute environment.
The wash-out solution contains unreacted component and resin,
that may pollute watercourse.
Methods for Cleaning up Carefully pick up and collect the dropped plates.
Wipe the area with a cloth containing soapy water to remove
any adherent material.
Remove all the spilt wash-out solution with absorbent.
7 HANDLING AND STORAGE
HANDLING
Technical Measures Wash hands thoroughly after handling unexposed or exposed plates.
Pay attention not to contact skin and eyes with the plate material.
Wear protective equipment like impervious gloves, if necessary.
Precautions Use with adequate ventilation or local exhaust system especially for
washing-out and drying processes.
Do not inhale fumes and gases while processing the material.
Do not contact skin and eyes with the wash-out solution.
Do not inhale nor contact with hazardous product pieces, liquid or gases
which may remain in the used containers.
Safe Handling Advice Pay attention not to get hurt to hands while cutting the plate.
Handle with care not to get hurt to hands with outer case or edge of the plate.
STORAGE
Technical Measures Put the packages vertical, and not pile up. Pay attention not to
fall them down.
Incompatible Products Oxidizers
Keep away from water and alcohol in which the material is soluble.
Store plates in a cool (below 25), and dry location, away from
Storage Conditions
sources of intense heat and ignition.
Put and store all the unexposed plates into the particular masking bag.
Packaging Materials Masking bag or corrugated board package
3/4
Printight KF-G, KM-G, KA-G, KM-A Type
First issue: June 10, 2004
Revised: February.23, 2007
MSDS No.F0509K
Material Safety Data Sheet
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
ENGINEERING MEASURES Use with adequate ventilation or local exhaust system especially for
washing-out and drying processes. Ensure eyewash/safety shower
stations are available near areas where the material is used.
-caprolactam Methyl alcohol Methyl acrylate Methyl methacrylate
Control Parameters
ACGIH 5ppm(vapor) 200ppm 2ppm 50ppm
TLV-TWA (23mg/m3) (260mg/m3) (7mg/m3) (410mg/m3)
(year) 1998 1998 1997 1999
PERSONAL PROTECTIVE EQUIPMENT
Respiratory Protection Wear a suitable gas mask, depending upon the task
Hand Protection Wear impervious rubber or plastic gloves
Eye Protection Wear safety glasses, goggles or face shield
Skin and Body Protection Wear impervious clothing to prevent skin from contacting the material
9 PHYSICAL AND CHEMICAL PROPERTIES
Physical State, Form, Color Solid sheet, Colorless transparent, slightly sweet odor
and Odor
pH 6.4 as washing-out solution
110
Melting Point
Decomposition Temperature No data available
Flash Point No data available
Autoignition Temperature No data available
Explosion Properties None
Density 1.2 g/cm3
Solubility Soluble in water and alcohol.
10 STABILITY AND REACTIVITY
Stability Stable under normal storage and handling.
Possible Hazardous Reactions Inflammable with the existence of ignition sources
Conditions to Avoid Avoid high temperature, flame and heat-sources and direct sunlight
Material to Avoid Avoid strong oxidizers
When subjected to prolonged high temperature or burning, this
Hazardous Decomposition Products
product will emit harmful gas containing carbon monoxide, nitrogen
oxides, chlorine compounds and sulfur oxides.
11 TOXICOLOGICAL INFORMATION
Acute Toxicity Oral-Rat LDLo2000mg/kg
Local Effects (skin and eye) Skin-Rabbit test: Printight KF-G, KM-G, KA-G, KM-A type has no irritation potential
under the conditions of this study.
Eye effects-Rabbit test: Printight KF-G, KM-G, KA-G, KM-A type has reversible and
mild irritation potential under the conditions of this study.
Mutagenicity Ames test: Printight KF-G, KM-G, KA-G, KM-A type is not mutagenic under the test
conditions employed.
4/4
Printight KF-G, KM-G, KA-G, KM-A Type
First issue: June 10, 2004
Revised: February.23, 2007
MSDS No.F0509K
Material Safety Data Sheet
12 ECOLOGICAL INFORMATION
Mobility
Unexposed plate and washed-out solution of exposed plate are soluble in water,and are
possible to diffuse in watercourse.
13 DISPOSAL CONSIDERATIONS
ispose of in accordance with all applicable local and
Waste from Residues
national lows/regulations.
Contaminated Packaging Dispose of as well as the waste material.
14 TRANSPORT INFORMATION
International Regulations
UN Classification Number Not applicable
Specific Precautionary When loading the package, pay attention not to fall it down nor drop it.
Transport Measures and because of its heavy weight.
Conditions Keep it dry and handle with care.
15 REGULATORY INFORMATION
Follow all the laws and regulations in your country.
16 OTHER INFORMATION
The information in this MSDS, to the best of our knowledge, is accurate and correct.
Notice
However, TOYOBO makes no warranty and assumes no liability whatsoever in
connection with any use of this information. The MSDS is subject to revision as new
information becomes available.
|