MATERIAL SAFETY DATA SHEET
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT: P Adhesive November 13, 2008
Vishay Micro-Measurements MSDS # MGM068B
Post Office Box 27777
Raleigh, NC 27611
919-365-3800
CHEMTREC 1-800-424-9300 (U.S.)
703-527-3887 (Outside U.S.)
NOTE: CHEMTREC numbers to be used only in the event of chemical emergencies involving a spill, leak, fire,
exposure or accident involving chemicals.
SECTION 2: HAZARDOUS INGREDIENTS / IDENTITY INFORMATION
CAS NUMBER CHEMICAL IDENTITY %
872-50-4 N-Methylpyrrolidone 62
1330-20-7 Xylene 19
100-41-4 Ethyl Benzene 4
71-43-2 Benzene Approx. 1 ppm
N/A Solids Approx. 15
SECTION 3: HEALTH HAZARD DATA
Routes of Entry:
Inhalation: Yes Skin: Yes Ingestion: Accidental
Health Hazards (Acute and Chronic): Causes skin burns. Causes eye and respiratory tract irritation.
Carcinogenicity: NTP: Not listed
IARC Monographs: Not listed
OSHA Regulated: Not listed
DOCUMENT NO.: 14071 805-FRM011
P Adhesive MSDS # MGM068B
Signs and Symptoms of Exposure:
INHALATION: May cause respiratory tract irritation. Excessive exposure may result in headache, dizziness,
incoordination, nausea, loss of appetite and loss of consciousness.
EYE CONTACT: May cause severe eye irritation.
SKIN CONTACT: May cause skin burns.
INGESTION: May cause irritation and burns to mouth and digestive tract.
Conditions Generally Aggravated by Exposure: None listed.
SECTION 4: EMERGENCY AND FIRST AID PROCEDURES
INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen.
Get medical attention.
EYE CONTACT: Immediately flush with plenty of water for at least 15 minutes.
SKIN CONTACT: Immediately flush with plenty of water for at least 15 minutes while removing contaminated
clothing and shoes. Wash clothing before reuse. Destroy contaminated shoes. Get medical attention.
NOTE: Skin absorption may add to the overall exposure.
INGESTION: Call physician or poison control center.
SECTION 5: FIRE AND EXPLOSION HAZARD DATA
Flash Point (Method Used): 80-100癋 (27-38?C) Pensky-Martens, Closed Cup
Flammable limits: LEL: Not known UEL: Not known
Extinguishing Media: Water spray, foam, dry chemical, carbon dioxide or any Class B extinguishing agent.
Special Firefighting Procedures: Fire fighters and others who may be exposed to products of combustion should
wear full protective clothing including self-contained breathing apparatus. Equipment should be thoroughly
decontaminated after use.
Unusual Fire and Explosion Hazards: Closed containers exposed to heat may build up pressure. Use water
spray to keep exposed containers and equipment cool.
2
DOCUMENT NO.: 14071 805-FRM011
P Adhesive MSDS # MGM068B
SECTION 6: ACCIDENTAL RELEASE MEASURES
Steps to be taken if material is released or spilled: Remove any source of sparks, flame or hot surfaces. Insure
adequate ventilation. Absorb with commercial absorbing materials and dispose of as a hazardous waste. Flush
area with water. Keep out of sewers, watersheds, and water systems.
SECTION 7: EXPOSURE CONTROLS -- PERSONAL PROTECTION
Respiratory Protection: Avoid breathing vapor and/or mist. Use NIOSH/MSHA approved respiratory protection
equipment when airborne exposure limits are exceeded. Consult respirator manufacturer to determine appropriate
type equipment for given application. Observe respirator use limitations specified by NIOSH/MSHA or the
manufacturer. Respiratory Protection Programs must comply with 29 CFR 1910.134.
Ventilation: Provide natural or mechanical ventilation to control exposure levels below airborne exposure limits. If
practical, use local mechanical exhaust ventilation at sources of air contamination such as open process
equipment.
Protective Gloves: Wear appropriate chemical resistant gloves to prevent skin contact.
Eye Protection: Wear chemical safety goggles, and a face shield when splashing is likely.
Other Protective Clothing or Equipment: Wear chemical resistant clothing to prevent skin contact. Wear a
chemical resistant apron when splashing is likely.
Work / Hygienic Practices: Wash immediately if skin is contaminated. Remove contaminated clothing promptly
and launder before reuse. Clean protective equipment before reuse. Provide a safety shower at any location
where skin contact can occur. Wash thoroughly after handling and before eating, drinking or smoking.
SECTION 8: HANDLING AND STORAGE
Precautions to be taken in handling and storing: Do not get into eyes, on skin, or on clothing. Avoid breathing
vapors or mists. Keep container closed. Use with adequate ventilation. Wash thoroughly after handling.
Other Precautions: Container hazardous when empty. Emptied containers retain vapor and product residue.
Follow labeled warnings even after container is emptied. Residual vapors may explode on ignition. Do not cut, drill,
grind or weld on or near container.
3
DOCUMENT NO.: 14071 805-FRM011
P Adhesive MSDS # MGM068B
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Boiling Point: Not known
Vapor Pressure (mmHg): 10
Vapor Density (Air = 1): 3.66
Specific Gravity (H2O = 1): 1.05-1.08
Melting Point: Not known
Evaporation Rate (BuAc = 1): Not known
Volatile Organic Compounds: 23%
Solubility in Water: Negligible
Appearance and Odor: Clear amber semi-viscous liquid with amine-like odor.
SECTION 10: STABILITY AND REACTIVITY DATA
Stability: Stable under normal conditions of use and storage.
Conditions to Avoid: Do not expose to heat or ignition sources. Volatiles given off during cure ?ethanol, n-
methylpyrrolidone, xylene.
Incompatibility (Materials to Avoid): Strong oxidizing agents, strong alkali.
Hazardous Decomposition or By-products: Carbon monoxide, nitrogenous products.
Hazardous Polymerization: Does not occur.
SECTION 11: TOXICOLOGICAL INFORMATION
N-Methylpyrrolidone
OSHA PEL: None established
ACGIH TLV: None established
OTHER: 2 ppm (8 mg/m3 Skin 8 hour)
Xylene
OSHA PEL: 100 ppm (150 ppm STEL)
ACGIH TLV: 100 ppm (150 ppm STEL)
OTHER: None established
Ethylbenzene
OSHA PEL: 100 ppm (125 ppm STEL)
ACGIH TLV: 100 ppm (125 ppm STEL)
OTHER: None established
4
DOCUMENT NO.: 14071 805-FRM011
P Adhesive MSDS # MGM068B
SECTION 12: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Dispose of in accordance with local, state, and federal environmental regulations.
SECTION 13: TRANSPORTATION INFORMATION
SHIPPING NAME CLASS PACKING GROUP UN NUMBER
Adhesives
(N-Methylpyrrolidone, Xylene) 3 II 1133
SECTION 14: REGULATORY INFORMATION
SECTION 313 SUPPLIER NOTIFICATION:
This product contains a toxic chemical or chemicals (as listed below) subject to the reporting requirements of
Section 313 Title III of the Superfund Amendment and Reauthorization Act of 1986 and 40 CFR Part 372.
CAS NUMBER CHEMICAL NAME % BY WEIGHT
872-50-4 N-Methylpyrrolidone 62
1330-20-7 Xylene 19
100-41-4 Ethyl Benzene 4
TSCA NOTIFICATION:
All components of this product are listed in the Toxic Substance Control Act Chemical Substance Inventory (TSCA).
SECTION 15: OTHER INFORMATION
To the best of our knowledge, the information provided above meets the requirements of the United States
Occupational Safety and Health Act and regulations established under 29 CFR 1910.1200 (g)(2)(c)(1)-(4) for a
mixture of hazardous chemicals which has not been tested as a whole. The data provided on this Material Safety
Data Sheet is from manufacturers of the original components. Vishay Micro-Measurements specifically disclaims
any and all form of liability and/or responsibility for the application of this product.
5
DOCUMENT NO.: 14071 805-FRM011
|