Reichhold, Inc. Street Address:
Corporate Headquarters 2400 Ellis Road, Durham, NC 27703
P.O. Box 13582
Research Triangle Park, NC 27709-3582
R72
8am to 5pm Phone: 1-800-275-6353
24-Hour Emergency Phone: 1-800-424-9300
MSDS No: 7763
Effective Date: 9/22/06 Material Safety Data Sheet
1. PRODUCT IDENTIFICATION
Health: 2*
3
Trade Name: POLYLITE?33306-12 Flammability: 3
2 1
Reactivity: 1
Chemical Family: Styrene-Suppressed Polyester Resin
Personal Protection:
Intended Use: Bathroom Component Resin
HMIS RATING
NFPA RATING
2. COMPOSITION / INFORMATION ON INGREDIENTS
O CAS No. CHEMICAL IDENTITY EXPOSURE LIMITS CARCINOGEN
S STATUS
H ACGIH OSHA MFR. IARC NTP OSHA
A TWA STEL PEL STEL
* 100-42-5 Styrene 20 ppm 40 ppm 100 NE NE Yes NR NR
ppm
Common Styrene Monomer
Name:
Concentration < 38.00 wt%
Proprietary Polyester Resin NE NE NE NE NE NR NR NR
Concentration 52.00 wt%
* Proprietary Cobalt Compounds 0.02 NE 0.1 NE NE Yes NR NR
mg/m3 mg/m3
Concentration < 0.20 wt%
* 25013-15-4 Vinyl Toluene 50 ppm 100 100 NE NE NR NR NR
ppm ppm
Common Vinyl Toluene
Name:
Concentration < 9.00 wt%
* 79-41-4 Methacrylic Acid 20 ppm NE 20 ppm NE NE NR NR NR
Concentration < 1.00 wt%
NE = Not Established NR = Not Reviewed * = OSHA Hazardous Ingredient
Reference Notes: Refer to Section 8, Subheading "Exposure Guidelines", for additional information concerning exposure limits.
3. HAZARDS IDENTIFICATION
Emergency Overview: Appearance: Blue Hazy Liquid Pungent Odor
FLAMMABLE liquid and vapor.
Harmful if swallowed - can enter lungs and cause damage
May undergo polymerization.
Page 1 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
Route(s) of Entry: Inhalation, ingestion, skin and eye.
Acute Exposure: INHALATION: Harmful if inhaled. Effects from exposure may include headaches, fatigue, nausea, sensation
of drunkeness, central nervous system depression and pulmonary edema. Inhalation of vapor or aerosol may cause irritation to the
respiratory tract (nose, throat, and lungs).
SKIN: Harmful if absorbed through skin. Contact causes skin irritation. Prolonged or repeated skin contact can result in defatting
and drying of the skin.
EYES: Harmful to eyes. Direct contact with this material causes eye irritation. Symptoms may include stinging, tearing, redness
and swelling.
INGESTION: Harmful if swallowed. Single dose oral toxicity is low. Swallowing small amounts during normal handling is not
likely to cause harmful effects; swallowing large amounts may be harmful. Effects from exposure through ingestion may include
gastrointestinal disturbances, pain and discomfort. Effects of exposure by ingestion may also include those indicated by the
inhalation route. Material is harmful or fatal if liquid is aspirated into the lungs.
Chronic Exposure: Overexposure to this material (or its components) has been suggested as a cause of the following effects in
humans and may aggravate pre-existing disorders of these organs; central nervous system effects, effects on hearing and respiratory
tract damage. Prolonged or repeated exposure may cause liver and kidney damage.
Carcinogenicity: This material contains styrene which is listed by the International Agency for Research (IARC) on Cancer as a
group 2B cancer causing agent (possibly carcinogenic to humans).
This material contains Cobalt Compounds which is listed by the International Agency for Research on Cancer (IARC) as a Group
2B cancer causing agent (possibly carcinogenic to humans).
4. FIRST AID MEASURES
Eye Contact: Immediately flush eyes with large quantities of clean water for at least 15 minutes. Get immediate medical attention.
Skin Contact: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation develops or
persists. Wash contaminated clothing before reuse.
Ingestion: DO NOT INDUCE VOMITING. ASPIRATION HAZARD: this material may enter the lungs during vomiting.
Immediately give the victim one or two glasses of water or milk to drink. Never give anything by mouth to an unconscious person.
GET IMMEDIATE MEDICAL ATTENTION.
Inhalation: Remove victim to fresh air. Keep warm and quiet. If not breathing, give artificial respiration. If breathing is difficult,
give oxygen by trained personnel. GET IMMEDIATE MEDICAL ATTENTION.
5. FIRE FIGHTING MEASURES
89?F (32 ?C)
Flash Point:
SetaFlash Closed Cup
Flash Point Method Used:
1.1 % in air Styrene
Flammable Limits in Air (Lower):
7 % in air Styrene
Flammable Limits in Air (Upper):
914?F (490 ?C) Styrene
Autoignition:
General Hazards: FLAMMABLE LIQUID: This material's flash point is less than 100癋 (38癈).
Fire Fighting Extinguishing Media: Use carbon dioxide, foam, dry chemical or water fog to extinguish fire.
Page 2 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
Fire Fighting Equipment: Wear self-contained breathing apparatus (SCBA) and full fire-fighting protective clothing.
Thoroughly decontaminate all protective equipment after use.
Fire Fighting Instructions: Evacuate all persons from the fire area to an explosion-protected location. Move non-burning
material, as feasible, to a safe location as soon as possible. Fire fighters should be protected from potential explosion hazard while
extinguishing the blaze. Containers of this material may build up pressure if exposed to heat (fire). Use water spray to cool fire-
exposed containers. DO NOT extinguish a fire resulting from the flow of this flammable liquid until the flow of liquid is
effectively shut off. This precaution will help prevent the accumulation of an explosive vapor-air mixture after the initial fire is
extinguished. Use water spray to disperse vapors if a spill or leak has not ignited.
Fire and Explosion Hazards: FLAMMABLE LIQUID. Vapors can form an explosive mixture with air. Vapor can travel to a
source of ignition (spark or flame) and flash back. This material may polymerize (react) when its container is exposed to heat (as
during a fire). This polymerization increases pressure inside a closed container and may result in the violent rupture of the
container.
Hazardous Combustion Products: Combustion may produce carbon monoxide, carbon dioxide and irritating or toxic vapors and
gases.
6. ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: FOR SMALL SPILLS: Absorb spill with inert material (e.g., dry sand or earth), then place in a
chemical waste container. Use non-sparking (non-metallic) tools to clean up spill. Remove all sources of ignition. NO SMOKING.
FOR LARGE SPILLS: Eliminate all ignition sources (flares, flames including pilot lights, electrical sparks). NO SMOKING.
Persons not wearing protective equipment (see Section 8) should be excluded from the area of the spill until clean-up has been
completed. Stop spill at source. Prevent spilled material from contaminating soil or entering drains, sewers, streams or other bodies
of water. Prevent spilled material from spreading. Immediately notify authorities of any reportable spill as may be required pursuant
to regulations. See Section 15 for applicable CERCLA reportable quantities. Pump or vacuum transfer spilled product to clean
containers for recovery. Absorb unrecoverable product. Transfer contaminated absorbent, soil and other waste materials to waste
containers for disposal.
7. HANDLING AND STORAGE
Signal Word: W A R N I N G
Handling Information: Avoid inhalation and contact with eyes, skin, and clothing. Wash hands thoroughly after handling and
before eating or drinking. Remove and wash contaminated clothing before reuse. Use with adequate ventilation. Ground and bond
containers when transferring the material to prevent static electricity sparks which could ignite the vapor. Use spark-proof tools
and explosion-proof equipment. Consult your supplier of promoters and catalysts for additional instructions on proper mixing and
usage.
Empty containers may retain product residue (liquid and/or vapor). Do not pressurize, cut, weld, braze, solder, drill, grind, or
expose these containers to heat, flame, sparks, static electricity, or other sources of ignition as the container may explode and may
cause injury or death. Empty drums should be completely drained and properly bunged. Empty drums should be promptly returned
to a drum reconditioner or properly disposed.
Storage Information: Keep away from ignition sources: flames, pilot lights, electrical sparks, and sparking tools. NO
SMOKING. Do not store in direct sunlight. Store separate from oxidizing materials, peroxides, and metal salts. Keep container
closed when not in use. To ensure maximum stability and maintain optimum resin properties, resins should be stored in closed
containers at temperatures below 75癋 (25癈). Copper or copper containing alloys should be avoided as containers.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Page 3 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
Exposure Guidelines: The Occupational Safety and Health Administration (OSHA), has established for styrene, a Permissible
Exposure Limit (PEL) of 100 ppm for an 8 hour Time Weighted Average (TWA); 200 ppm for an acceptable ceiling concentration;
and a 600 ppm concentration within a duration of 5 minutes in any 3 hours as an acceptable maximum peak above the acceptable
ceiling concentration for an 8 hour shift. While the federal workplace exposure limit for styrene is 100 ppm, OSHA accepted the
styrene industry's proposal to voluntarily meet a PEL of 50 ppm on an 8 hour TWA and a Short Term Exposure Limit (STEL) of
100 ppm, 15 minute exposure.
The American Conference of Governmental Industrial Hygenists (ACGIH) have established, for styrene, Threshold Limit Values
(TLV) of 20 ppm or 85 mg/m3 TWA and 40 ppm or 170 mg/m3 Short Term Exposure Limit (STEL), 15 minute exposure.
The OSHA PEL and ACGIH TLV for methacrylic acid are both set at 20 ppm for an 8-hour TWA.
The Occupational Safety and Health Administration (OSHA), has established for vinyl toluene, a Permissible Exposure Limit
(PEL) of 100 ppm or 480 mg/m3 for an 8 hour Time Weighted Average (TWA).
The American Conference of Governmental Industrial Hygenists (ACGIH) have established, for vinyl toluene, Threshold Limit
Values (TLV) of 50 ppm or 242 mg/m3 TWA and 100 ppm or 483 mg/m3 Short Term Exposure Limit (STEL), 15 minute
exposure.
The US Occupational Safety and Health Administration (OSHA) has established for Cobalt Compounds (metal dust and fume, as
Co) a Permissible Exposure Limit (PEL) of 0.1 mg/m3 for an 8-hour Time Weighted Average (TWA).
Engineering Controls: Local ventilation may be required during certain operations to maintain concentrations below
recommended exposure limits. Use explosion-proof ventilation equipment.
Eye Protection: Wear 1) safety glasses with side shields and a faceshield or 2) goggles and a faceshield. Facilities storing or
utilizing this material should be equipped with an eyewash station and safety shower.
Skin Protection: Wear chemical resistant gloves such as polyvinyl alcohol or Viton? If splashing is likely, wear impervious
clothing and boots to prevent repeated or prolonged skin contact. Consult your supplier of personal protective equipment for
additional instructions on proper usage.
Respiratory Protection: A NIOSH/MSHA approved air purifying respirator with organic vapor cartridge or canister may be
necessary under certain circumstances where airborne concentrations are expected to exceed exposure limits. A respiratory
protection program that meets OSHA's 29 CFR 1910.134 and ANSI Z88.2 requirements must be followed whenever workplace
conditions warrant a respirator's use. Protection provided by air purifying respirators is limited. Use a positive pressure air-
supplied respirator if 1) there is any potential for an uncontrolled release, 2) exposure levels are not known, or 3) during other
circumstances where air purifying respirators may not provide adequate protection.
9. PHYSICAL AND CHEMICAL PROPERTIES
Blue, Hazy
Color:
Pungent
Odor:
0.2 ppm Styrene
Odor Threshold:
Liquid
Physical State:
Insoluble at 20癈 (68 癋) Dispersion
Solubility in Water:
6.12 (mm Hg) Styrene
Vapor Pressure:
1.04 - 1.12 (Water = 1) at 25癈 (77 癋)
Specific Gravity:
295?F (146 ?C) Styrene
Boiling Point:
-22.7癋 (-30.4 癈) Styrene
Freezing Point:
< 1 (BuAc=1)
Evaporation Rate:
3.6 (AIR=1) Styrene
Vapor Density:
48 % by weight
% Volatile:
518 grams/liter (calculated)product as supplied
VOC Content:
Not applicable
pH:
Page 4 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
10. STABILITY AND REACTIVITY
Stability: Stable at normal temperatures and storage conditions.
Incompatibility: Avoid contact with strong acids, oxidizing agents (peroxides), metal salts and polymerization catalysts.
Hazardous Decomposition Products: Thermal decomposition may produce various hydrocarbons and irritating, acrid vapors.
Hazardous Polymerization: Product will undergo hazardous polymerization at temperatures above 150 F (65 C). Hazardous
polymerization will occur if contaminated with peroxides, metal salts and polymerization catalysts.
11. TOXICOLOGICAL INFORMATION
Acute Eye Toxicity: Studies indicate that exposures to concentrations of styrene above 200 ppm cause irritation of the eyes.
Styrene causes transient moderate eye irritation without corneal involvement.
Vinyl toluene: (rabbit), undiluted, slight conjunctival irritation, no corneal injury.
Acute Skin Toxicity: Draize Skin Primary Irritation Score (range, 0-8) for a 4-hour exposure (rabbits) to styrene is 6.6. Styrene:
dermal LD50 (rabbit), 5 g/kg. Styrene causes severe irritation at 72 hours.
Methacrylic Acid: dermal LD50 (rat), 500 mg/kg.
Vinyl toluene monomer: dermal LD50 (rabbit), 4,500 mg / kg.
Acute Inhalation Toxicity: Styrene: inhalation LC50 (rat), 24 g/m3 / 4 hrs. Studies indicate that exposures to concentrations of
styrene above 200 ppm cause irritation of the upper respiratory tract. Acute exposure to high concentrations of styrene may
produce irritation of the mucous membranes of the upper respiratory tract, nose, and mouth, followed by symptoms of narcosis,
muscular contraction, and death due to respiratory center paralysis.
Vinyl toluene monomer: inhalation LC50 (mouse), 3,000 mg / cu m.
Acute Oral Toxicity: Styrene: oral LD50 (rat), 5 g / kg.
Methacrylic Acid: oral LD50 (rat), 1060 mg/kg.
Vinyl toluene: oral LD50 (rat), 4,000 mg / kg; (mouse), 3.16 g / kg.
Subchronic: Styrene: inhalation NOEL(rat) 200 ppm 6 hr / day 13 weeks, target organ effects: auditory response; inhalation
LOEL (rat) 800 ppm 6 hr / day 3 - 13 weeks, target organ effects: auditory response.
Styrene has been shown to cause probable hearing loss in rats exposed for at least six hours per day for three to thirteen weeks to
800 ppm of styrene in the air, as indicated by a rise in the auditory brainstem response threshold and loss of hair cells of the inner
ear. No effects were observed in rats exposed to styrene at 200 ppm for 13 weeks. Based on animal studies and human experience,
no significant risk of hearing loss is expected in occupationally exposed persons.
Overexposure to styrene has been suggested as a cause of the following effects in laboratory animals and may aggravate pre-
existing disorders of the following organs in humans; mild, reversible kidney effects, effects on hearing, respiratory tract damage,
testis damage and liver damage.
Vinyl toluene inhalation (1250 ppm, 7-8 hr/day for 92 - 100 days) increases kidney and liver weights and causes fatty degeneration
of these organs in rats, guinea pigs, rabbits and monkeys. Exposure to 600 ppm did not cause any microscopic or macroscopic
organ changes. A 12 week inhalation administration of 300 ppm vinyl toluene causes slight increases in secondary lysosomes in the
rat liver.
Vinyl toluene exhibited a central nervous system (CNS) depressant effect during exposure of mice, rats, guinea pigs and rabbits by
various routes (oral, inhalation and skin). During repeated exposure for 1 month, vinyl toluene had some effect on the CNS of mice,
Page 5 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
and during chronic inhalation at 0.03 mg/L it caused a reduction in weight of mice and symptoms of intoxication in the offspring of
guinea pigs.
Chronic/Carcinogenicity: The International Agency for Research on Cancer (IARC) has classified styrene in Group 2B, possibly
carcinogenic to humans. IARC concluded that evidence of carcinogenicity from human health studies, was inadequate and based
the classification on animal and other relevant data. The animal data included an increased incidence of cancer observed in a few
studies in which rats and mice were given styrene by inhalation or by ingestion for their lifetimes. IARC considered the combined
results of these cancer studies to provide "limited evidence" of carcinogenicity. Other scientists consider the results of these studies
inadequate to assess human carcinogenicity because these studies had either negative or statistically inconclusive results or had
serious problems such as poor study design or very high mortality. Other relevant data included results from in-vivo and in-vitro
genotoxicity studies. IARC also relied on data on styrene oxide including the results of two studies demonstrating stomach tumors
in rats that were fed styrene oxide for their lifetime. Several epidemiology studies involving workers in the styrene, polystyrene or
reinforced plastics industries have been conducted. Together, these studies show no increased cancer risk from occupational
exposure to styrene.
Preliminary results of a recent inhalation study indicated that mice exposed to styrene showed an increased incidence of lung
tumors, however no dose response relationship was observed. The relevance of these findings is uncertain since data from other
long-term animal studies and from epidemiology studies of workers exposed to styrene do not provide a basis to conclude that
styrene is carcinogenic.
The American Conference of Governmental Industrial Hygienists (ACGIH) has adopted the listing of Styrene as "A4-Not
Classifiable as a Human Carcinogen." There is inadequate data on which to classify the agent in terms of its carcinogenicity in
humans and/or animals.
The American Conference of Governmental Industrial Hygienists (ACGIH) has adopted the listing of Vinyl Toluene as "A4-Not
Classifiable as a Human Carcinogen." There is inadequate data on which to classify the agent in terms of its carcinogenicity in
humans and/or animals. The International Agency for Research on Cancer (IARC) has classified vinyl toluene in Group 3, not
classifiable as to its carcinogenicity to humans.
This material contains Cobalt Compounds which is listed by the International Agency for Research on Cancer (IARC) as a Group
2B cancer causing agent (possibly carcinogenic to humans).
Sensitization: No information is available.
Teratology: Styrene did not cause birth defects in orally-dosed rats, mice, rabbits and hamsters exposed by inhalation. Styrene
given by inhalation for six hours a day during organ development has been shown to be toxic to fetal mice at 250 ppm and to fetal
hamsters at 1000 ppm. Information from human experience and the results of animal studies suggest no significant risk of birth
defects or reproductive toxicity of styrene to humans.
Subchronic inhalation of 6 ppm (29 mg/cu m) vinyl toluene by guinea pigs for 4 months produced teratogenic effects.
Reproduction: No information is available.
Mutagenicity: Styrene has given mixed positive and negative results in a number of mutagenicity tests. It was not mutagenic in the
Ames test without metabolic activation but gave negative and positive mutagenic results with metabolic activation. It has also given
negative mutagenic results in the Chinese Hamster Ovary Test, and the Forward Gene Mutation Test and positive results in the
Sister Chromatid Exchange and the Chromosomal Aberration assay.
Vinyl toluene was tested for potential to induce chromosome aberrations and sister chromatid exchange in phytohemagglutinin-
stimulated human lymphocytes cultured for 48 hours (aberration analysis) or 72 hour (sister chromatid exchange analysis). The
treatments were carried out 24 hour (aberrations) or 48 hour (sister chromatid exchange) before harvest. The toxicity of vinyl
toluene was similar to that of styrene. Chromosome aberrations were observed in cells treated with 0.33 to 4.00 mmolar vinyl
toluene. Like styrene, vinyl toluene is converted in vitro to reactive metabolites, presumably epoxides.
Additional Information: No toxicological data is available for this product. Based on properties and similar polymers, the
polyester resin is not hazardous.
Page 6 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
12. ECOLOGICAL INFORMATION
Ecotoxicity: Styrene is toxic to aquatic organisms and should not be released to sewage, drainage systems and all bodies of water
at concentrations exceeding approved limits under applicable regulations and permits. Styrene: LC50 (Sheepshead minnow), 9.1
mg / l / 96 hr.
Environmental Fate: Styrene released to soil is subject to biodegradation. The results of one extensive biological screening study
suggest that styrene will be rapidly destroyed by biodegradation in most aerobic environments, but the rate may be slow at low
concentrations in aquifers and lake waters and in environments at low pH (6).
Terrestrial Fate: If released to soil, vinyl toluene is predicted to be moderately mobile. The compound has the potential to undergo
photolysis on surface soils. Volatilization may be a significant removal process.
Aquatic Fate: If released to water, vinyl toluene could potentially volatilize, photolyze, react with naturally occurring oxidants
found in water, or adsorb to suspended solids and sediments in water. Bioaccumulation in aquatic organisms is not expected to be
an important fate process.
Atmospheric Fate: The relatively high vapor pressure of vinyl toluene, suggests that the o-, m- and p- isomers would exist almost
entirely in the vapor phase in the atmosphere.
13. DISPOSAL CONSIDERATIONS
Waste Disposal Method: RCRA HAZARDOUS WASTE: This material and containers that are not empty, if discarded, would be
regulated as a hazardous waste under RCRA. Treatment and/or disposal must be completed at a RCRA-permitted Treatment,
Storage and Disposal Facility (TSD). The storage and transportation of RCRA hazardous wastes are also regulated by the USEPA.
EMPTY DRUMS: "Empty containers", as defined under 40 CFR 261.7 or other applicable state or provincial regulations or
transportation regulations, are not classified as hazardous wastes.
RCRA Hazard Class: D001 (IGNITABLE): When discarded in its purchased form, this material would be regulated under 40
CFR 261.21 as EPA Hazardous Waste Number D001 based on the characteristic of ignitability.
14. TRANSPORT INFORMATION
DOT / IATA / IMDG: Non Bulk
RESIN SOLUTION
Proper Shipping Name:
3
Hazard Class:
UN1866
ID Number:
III
Packing Group:
127
ERG Number:
DOT / IMDG: Bulk
RESIN SOLUTION
Proper Shipping Name:
3
Hazard Class:
UN1866
ID Number:
III
Packing Group:
127
ERG Number:
TDG: Bulk and Non-Bulk
RESIN SOLUTION
Proper Shipping Name:
3
Hazard Class:
UN1866
ID Number:
III
Packing Group:
127
ERG Number:
Page 7 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
Additional Information: US regulations require the reporting of spills when the amount exceeds the Reportable Quantity (RQ) for
specific components of this material. See CERCLA in Section 15, Regulatory Information, for the Reportable Quantities of specific
components.
15. REGULATORY INFORMATION
Clean Air Act -Hazardous Air Pollutants (HAP): The following chemical(s) are listed as hazardous air pollutants (HAP) under
the U.S. Clean Air Act Section 112(b)(1), (40 CFR 61): Styrene (CAS# 100-42-5) See Section 2 of this MSDS for amount. A
maximum of 0.5% of other HAP's may be present in this product.
Clean Water Act - Priority Pollutants (PP): Styrene (100-42-5) is listed under Section 311 as a Hazardous Substance.
Occupational Safety and Health Act (OSHA): This material is classified as a hazardous chemical under the criteria of the US
Occupational Safety and Health Administration (OSHA) Hazard Communication Standard, 29 CFR 1910.1200.
SARA Title III: Section 304 - CERCLA: Styrene (CAS# 100-42-5): Reportable Quantity = 1,000 lb.
SARA Title III: Section 311/312 - Hazard Communication Standard (HCS): This material is classified as an IMMEDIATE
HEALTH HAZARD, DELAYED HEALTH HAZARD, FLAMMABILITY HAZARD, and REACTIVITY HAZARD under the
US Superfund Amendment and Reauthorization Act (Section 311/312).
SARA Title III: Section 313 Toxic Chemical List (TCL): Styrene (100-42-5)
TSCA Section 8(b) - Inventory Status: All components of this material are listed on the US Toxic Substances Control Act
(TSCA) inventory.
TSCA Section 12(b) - Export Notification: Vinyl toluene (CAS # 25013-15-4) is subject to the US Toxic Substances Control
Act (TSCA) Section 12(b) Export Reporting requirements.
Canadian Inventory Status: All components of this material are listed on the Canadian Domestic Substances List (DSL).
Canadian WHMIS: This material is classified by the Canadian Workplace Hazardous Material Information System as: B2
(flammable liquid) D2A (materials causing other toxic effects, very toxic material) D2B (materials causing other toxic effects,
toxic material) F (dangerously reactive material)
California Proposition 65: W A R N I N G: This material contains a chemical known to the State of California to cause cancer
and birth defects or other reproductive harm.
Additional Canadian Regulatory Information: The following chemicals are listed on the WHMIS Ingredient Disclosure List:
Styrene Monomer (CAS# 100-42-5) Vinyl Toluene (CAS# 25013-15-4)
16. OTHER INFORMATION
7763
MSDS No:
Revise for color change.
Reason Issued:
Environment, Health and Safety Department
Prepared By:
09/22/06
Approved Date:
08/11/06
Supersedes Date:
Disclaimer: This information is provided in good faith and is correct to the best of Reichhold's knowledge as of the date hereof
and is designed to assist our customers; however, Reichhold makes no representation as to its completeness or accuracy. Our
products are intended for sale to industrial and commercial customers. We require customers to inspect and test our products before
use and to satisfy themselves as to suitability for their specific applications. Any use which Reichhold customers or third parties
make of this information, or any reliance on, or decisions made based upon it, are the responsibility of such customer or third party.
Reichhold disclaims responsibility for damages, or liability, of any kind resulting from the use of this information. THERE ARE
Page 8 of 9
POLYLITE?33306-12 Reichhold, Inc.
Effective Date: 9/22/06 MSDS No: 7763
NO WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, INCLUDING THOSE OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO THIS INFORMATION OR TO THE PRODUCT IT
DESCRIBES. IN NO EVENT SHALL REICHHOLD BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Page 9 of 9
|