MATERIAL SAFETY DATA SHEET
BLUGLOO LIGHT CURE ADHESIVE
1 - IDENTIFICATION 7 - EMERGENCY FIRST AID PROCEDURES
Manufacturer: Ormco Corporation Skin: Wash thoroughly with soap and water.
Address: 1717 West Collins Avenue Eyes: Flush with water for 15 minutes including under eyelids.
City, State, Zip: Orange, CA 92867 Inhalation: Remove to fresh air. Get medical attention if discomfort
persists.
Telephone: 1-800-854-1741
Ingestion: Rinse mouth out with water. Do not induce vomiting. Seek
24-Hour Emergency: Chemtrec 1-800-424-9300
medical attention.
Date Prepared: April 13, 2005
2 - COMPOSITION INFORMATION
8 - PRECAUTIONS FOR SAFE HANDLING & USE
Hazardous Ingredients
Steps to be taken in case material is released or spilled: Absorb
CAS # PEL TLV %
spills with inert material. Keep spilled material out of sewers.
Uncured Methacrylate Ester Monomers N/A N/A N/A 20-38
Waste Disposal Method: Unpolymerized material may be RCRA
hazardous waste. Incinerate uncured material in accordance with all
Other Ingredients
federal, state and local regulations.
Inert mineral fillers, fumed silica, activators and preservatives
Precautions to be taken in handling and storing: Store in a cool, dry
place away from heat, light and ignition sources.
3 - PHYSICAL AND CHEMICAL PROPERTIES
9 - CONTROL MEASURES
Boiling Point: N/D
Specific Gravity (H20 = 1): 1.16
Respiratory Protection: Avoid prolonged or excessive breathing of
Vapor Pressure (mm Hg): N/D
vapors of uncured material.
Vapor Density (AIR = 1): N/D
VENTILATION:
Freezing/Melting Point: N/D
Local Exhaust: Good general ventilation should be sufficient to
Solubility in Water: Insoluble
control airborne levels of vapors released by uncured material.
Appearance and Odor: Colored paste with fruity ester-like odor
Mechanical (General): Good general ventilation recommended.
4 - FIRE AND EXPLOSION HAZARD DATA Protective Gloves: Impervious rubber gloves recommended when
contacting uncured material.
Flash Point (Method Used): N/D Eye Protection: Safety glasses recommended.
Flammable Limits: LEL: N/D UEL: N/D Work/Hygiene Practices: Handle in accordance with good personal
Extinguishing Media: Chemical foam, CO2 or dry chemical hygiene and safety practices. These practices include avoiding
unnecessary exposure to uncured material.
Special Fire Fighting Procedures: Wear a self-contained breathing
apparatus.
Unusual Fire and Explosion Hazards: Heat can cause 10 - TRANSPORTATION INFORMATION
polymerization with rapid release of energy
5 - REACTIVITY DATA Not DOT regulated.
Stability: Stable if stored as directed. 11 - SPECIAL INFORMATION
Conditions to Avoid: Heat, light, aging and contamination
Incompatibility (Material to Avoid): Reducing and oxidizing agents, HMIS (Hazardous Material Identification System) Rating:
peroxides, and amines H2 F1 R2 PPE 鈥? Gloves and safety glasses.
Hazardous Decomposition Byproducts: Oxides of carbon [HMIS Hazard Index: 4 鈥? Severe Hazard; 3 鈥? Serious Hazard;
Hazardous Polymerization: May occur 2 鈥? Moderate Hazard; 1 鈥? Slight Hazard; 0 鈥? Minimum Hazard]
6 - HEALTH HAZARD DATA
Note: Hazard information contained on this MSDS form relates
only to material in its uncured state. Thorough biocompatibility
Routes of Entry:
and toxicity testing of the cured material and its extracts have
Skin: Prolonged or repeated exposure to uncured material may cause
demonstrated that the material is non-toxic.
irritation or skin rash especially in sensitive individuals.
Eyes: May cause irritation and damage if not removed promptly.
Inhalation: Prolonged or excessive inhalation may cause respiratory
tract irritation.
Ingestion: Uncured material may be harmful or fatal if swallowed.
Carcinogenicity - NTP: No
IARC Monographs: No OSHA Regulated Carcinogen: No
Note: This MSDS was prepared in accordance with the requirements of the OSHA Hazard Communication Standard (29 CFR 1910.1200) and
is to be used only for this product. The information contained in this MSDS is, to the best of our knowledge, believed to be accurate.
|