MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part B, Liquid Binder) (Part A, Powder Filler)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
The information contained herein is based upon data considered true and accurate. However,
OMEGA makes no warranties, express or implied, as to the accuracy or adequacy of the SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
information contained herein or the results to be obtained from the use thereof. This information
is offered solely for the user's consideration, investigation and verification. Since the use and
PRODUCT NAME: CC High Temperature Cement, Part A, Powder Filler
conditions of use of this information and the material described herein are not within the control
of OMEGA, OMEGA assumes no responsibility for injury to the user or third persons. The
SUPPLIER: OMEGA Engineering, Inc.
material described herein is sold only pursuant to OMEGA's Terms and Conditions of Sale,
ADDRESS: PO Box 4047
including those limiting warranties and remedies contained herein, it is the responsibility of the
Stamford, CT 06907
user to determine whether any use of this data and information is in accordance with applicable
TELEPHONE: (203) 359-1660
federal, state or local laws and regulations.
ITEM NUMBER: CC High Temperature Cement, Part A, Powder Filler
漏 Copyright 2005 OMEGA ENGINEERING, INC., ALL RIGHTS RESERVED
ITEM DESCRIPTION: Low Expansion Cement (Powder)
PRODUCT DESCRIPTION: Low Expansion Cement (Powder)
CHEMICAL FAMILY: Zirconium Silicate Cement Powder; aZrO2bSiO2
REVISION DATE: 09/05
PRODUCT USE: High temperature bonding/adhesive compounds
SECTION 2. COMPOSITION AND DATA ON COMPONENTS
COMPONENT CAS # ACGIH TLV OSHA PEL % WT
ZIRCONIUM SILICATE 14940-68-2 10 MG/M (TWA) 15 MG/M (STEL) <80%
3 3
SILICA, CRYSTALLINE 14808-60-7 0.1MG/M3 (TWA0 0.1 MG/M3 (STEL) <1%
SODIUM SILICO 1-6893-85-9 2.5MG/M3 2.5MG/M3 <30%
FLUORIDE
NOTES: Exposure values shown for guidance only. Please follow applicable regulations.
SECTION 3. HAZARDS IDENTIFICATION
HMIS rating
Health 1
Flammability 0
Reactivity 0
Personal protection E
THRESHOLD LIMIT VALUE: SiO2 - 0.1 mg/m3; F2 - 2.5mg/m3
EFFECTS OF OVEREXPOSURE: Since this product is a mixture, there is no exposure limit
established for it. Hazardous components and their associated permissible exposure limits are
listed in the section titled 鈥淐omposition and Data on Components鈥?. Specific health hazards from
the various ingredients include relevant symptoms: irritation to eyes, nose, throat, respiratory
system, and skin areas.
1 of 16
16 of 16
MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part A, Powder Filler) (Part B, Liquid Binder)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 15. REGULATORY INFORMATION (CONT'D)
SECTION 3. HAZARDS IDENTIFICATION (CONT'D)
CANADA
ACUTE: Inorganic fluorides are highly irritating and toxic. May cause irritation to respiratory
tract, skin, and eyes. Large doses can cause nausea, vomiting, and diarrhea. Circulatory, DSL: Components included on inventory.
respiratory complaints, and skin rashes may occur. Respiratory diseases including asthma and
emphysema may be aggravated. WHMIS HAZARD CLASS(ES):
Not controlled
CHRONIC: Exposure to fluorides over years may produce an embrittlement and densification of
bones, and increase calcification of ligaments. Repeated inhalation of respirable free silica dust WHMIS TRADE SECRET REGISTRY NUMBER(S): Not Applicable
may cause delayed lung injury (silicosis).
WHMIS SYMBOLS:
Stylized T
SECTION 4. FIRST AID MEASURES EUROPEAN ECONOMIC COMMUNITY (EEC)
EINECS Inventory: Components included on inventory
EYE CONTACT: Flush eyes immediately with water or physiological saline for at least 15
Irritant
minutes while lifting upper and lower lids. Seek medical attention.
EEC RISK庐 PHRASES:
INGESTION: Seek medical attention immediately. Give water to dilute. Do not induce vomiting
Irritating to eyes, respiratory system, and skin
unless directed by licensed medical personnel. Advise physician of possible fluoride exposure.
EEC SAFETY PHRASES
INHALATION: If difficulty breathing, move to fresh air at once. Apply artificial respiration if
Avoid contact with skin and eyes
breathing has stopped. Seek medical attention.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
Keep container tightly closed and dry
SKIN CONTACT: Wash contact area thoroughly with soap and water. Remove contaminated
clothing. Launder before reuse. Seek medical attention if erythema develops.
SECTION 16. OTHER INFORMATION
SECTION 5. FIRE FIGHTING MEASURES
This MSDS contains information and recommendations based upon our present knowledge and
data believed to be reliable. All data shown here are subject to reasonable variation and are
AUTO IGNITION TEMPERATURE: NA
supplied as an accommodation to the buyer. However, this shall not constitute a guarantee for
EXPLOSION DATA - Not sensitive to mechanical impact or static discharge. any specific product features and shall not establish a legally valid contractual relationship. This
MSDS applies only to the product in its 鈥渁s manufactured鈥? state, since the application to which
EXTINGUISHING MEDIA: NA
the product is subjected may change its characteristics. The buyer is responsible for
NOTE: Many dusts and aerosols may exhibit explosive characteristics if ignited by static determining the safety, toxicity, and suitability of the product under the conditions of their use of
discharge or spark. Exercise care to avoid causing dusting or misting. the product. Buyers also have the responsibility for insuring that the MSDS is available to their
employees, product users, and handlers.
FIRE AND EXPLOSION HAZARDS: Emits fluoride fumes if heated to decomposition
temperatures (932掳F).
NAV = Not Available NE = Not Established NA = Not Applicable
FIRE FIGHTING PROCEDURES: NA
FLAMMABILITY - Not flammable in presence of open flame, sparks, excessive heat and static
discharge.
FLAMMABLE LIMITS LEL: NA
FLAMMABLE LIMITS UEL: NA
FLASHPOINT: NA
2 of 16 15 of 16
MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part B, Liquid Binder) (Part A, Powder Filler)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 13. DISPOSAL CONSIDERATIONS SECTION 6. ACCIDENTAL RELEASE MEASURES
WASTE DISPOSAL: Comply with federal, state and local regulations. If approved, flush with CLEAN-UP PROCEDURE: Sweep, scoop, or vacuum the discharged material.
water to chemical sewer. For large quantities, neutralize with dilute acid and landfill solids or
Respiratory protection should be worn at all times and skin contact should be avoided. Observe
flush neutral liquid to sewer with plenty of water.
environmental regulations.
EUROPEAN COMMUNITY WASTE DISPOSAL KEY: Not known
UNCLEANED PACKAGINGS: Disposal must be made according to official regulations.
SECTION 7. HANDLING AND STORAGE
Avoid contact with eyes, skin, and clothing.
SECTION 14. TRANSPORT INFORMATION
Avoid breathing dust.
DOT I.D. NO.: NOT REGULATED
For industrial use only!
DOT SHIPPING NAME: HIGH TEMPERATURE BONDING MORTAR
Harmful if inhaled.
DOT HAZARD CLASS: NOT REGULATED
路May cause irritation.
DOT LABEL: NONE
Wear chemical splash goggles, gloves, and protective clothing.
OTHER: NA
Use adequate ventilation and employ respiratory protection where dust
may be generated.
SECTION 15. REGULATORY INFORMATION
Wash thoroughly after handling.
U.S. FEDERAL REGULATIONS: Store in a cool, dry place.
TSCA Status:
Components are included in the EPA Toxic Substances Control Act (TSCA Chemical Keep container closed when not in use.
Substances Inventory.
Keep away from food and drinking water.
SARA TITLE III:
Section 302 Extremely Hazardous Substances: None above detection limits.
Always mix well before using.
Section 311/312 (40 CFR 370) Hazardous Categories:
Irritant
Section 313: Toxic Categories (40 CFR 370) Toxic chemicals above 鈥淒e Minimis鈥? level are:
There are no listed chemicals above detection limits in this compound.
CERCLA:
None
14 of 16 3 of 16
MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part A, Powder Filler) (Part B, Liquid Binder)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 11. TOXICOLOGICAL INFORMATION
SECTION 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION
ACGIH NO
See Section 2 for the components that have limit values that require monitoring at the
workplace. IARC NO
EYE PROTECTION: Safety glasses with side shields, chemical-type goggles, or face shield. EFFECTS OF ACCUTE EXPOSURE: Refer to Section 3.
Contact lenses should not be worn.
EFFECTS OF CHRONIC EXPOSURE: Refer to Section 3.
RESPIRATORY PROTECTION: Use dust respirators in compliance with OSHA Standard
1910.134. For emergency, a self-contained positive pressure, breathing appartus or full-face MUTAGENIC EFFECTS: If not addressed in Section 3, the data is not available.
respirator is recommended. If TLV of any component is exceeded, use appropriate respiratory
protection or ventilate in accordance with OSHA Regulation 29 CFR Part 1910. REPRODUCTIVE TOXICITY: If not addressed in Section 3, the data is not available.
SKIN PROTECTION: Suitable protective gloves (neoprene, butyl rubber, or viton). Clothing TERATOGENIC EFFECTS: If not addressed in Section 3, the data is not available.
should be clean, long-sleeved workclothes. Wash thoroughly before eating, smoking, applying
cosmetics, etc. Thoroughly launder work clothes before reuse. Safety shower nearby. NAME(S) OF TOXICOLOGICALLY SYNERGISTIC PRODUCTS AND EFFECTS: If not
addressed in Section 3, data is not available.
VENTILATION: Normal ventilation for good working conditions should be used.
LC50/LD50: There is no data available.
OTHER PRECAUTIONS: Wash thoroughly after handling. Safety shower and eyewash station
should be within direct access. Keep containers closed. ADDITIONAL INFORMATION: Sodium silicate solution has no known chronic hazard.
EYE IRRITANT: Yes
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES INGESTION IRRITANT: Yes
INHALATION IRRITANT: Yes
% VOLATILE BY VOLUME: NA
BOILING POINT: NA RESPIRATORY SENSITIZER: No
COEFFICIENT OF WATER/OIL DISTRIBUTION: Not available
EVAPORATION RATE: NA SKIN IRRITANT: Yes
MELTING POINT: NA
ODOR THRESHOLD: Not available SKIN SENSITIZER: No
PH: NA
SPECIFIC GRAVITY: 4.5
VAPOR DENSITY: NA
SECTION 12. ECOLOGICAL INFORMATION
VAPOR PRESSURE: NA
AQUATIC TOXICITY: Sodium silicate solution has low toxicity (96-hr LD50=500-5,000mg/liter).
The 96 hr TLM in mosquitofish is 2,320mg/liter. High pH (alkalinity) of undiluted material is
SECTION 10. STABILITY AND REACTIVITY
harmful to aquatic life.
CONDITIONS TO AVOID: None.
HAZARDOUS DECOMPOSITION PRODUCTS: Hydrogen fluoride gas
HAZARDOUS POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: NA
INCOMPATIBILITY: Avoid contact with acids, acidic catalysts, strong oxidizers, strong lewis,
and mineral acids, and excessive heat.
STABILITY: Stable
4 of 16 13 of 16
MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part B, Liquid Binder) (Part A, Powder Filler)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 8. EXPOSURE CONTROLS AND PERSONAL PROTECTION SECTION 11. TOXICOLOGICAL INFORMATION
See Section 2 for the components that have limit values that require monitoring at the ACGIH NOT AVAILABLE
workplace.*
IARC YES
EYE PROTECTION: Chemical resistant goggles and/or face shield.
EFFECTS OF ACCUTE EXPOSURE: Refer to Section 3.
RESPIRATORY PROTECTION: Use NIOSH approved mist respirator where spray occurs. For
EFFECTS OF CHRONIC EXPOSURE: Refer to Section 3.
emergency, a self-contained breathing apparatus or a full-face respirator is recommended. If
TLV of any component is exceeded, use appropriate respiratory protection or ventilate in
MUTAGENIC EFFECTS: If not addressed in Section 3, the data is not available.
accordance with OSHA Regulation 29 CFR Part 1910.
REPRODUCTIVE TOXICITY: If not addressed in Section 3, the data is not available.
SKIN PROTECTION: Suitable protective gloves (neoprene, butyl rubber, or viton). Clothing
should be clean, long-sleeved workclothes. Wash thoroughly before eating, smoking, applying
TERATOGENIC EFFECTS: If not addressed in Section 3, the data is not available.
cosmetics, etc. Thoroughly launder work clothes before reuse. Safety shower nearby.
NAME(S) OF TOXICOLOGICALLY SYNERGISTIC PRODUCTS AND EFFECTS: If not
VENTILATION: Normal ventilation for good working conditions should be used.
addressed in Section 3, data is not available.
OTHER PRECAUTIONS: Avoid floor spills.
ADDITIONAL INFORMATION: Crystalline Silica (Quartz)
Silicosis - The major concern is silicosis caused by the inhalation of respirable crystalline silica
dust. Silicosis can exist in several forms, chronic (or ordinary), accelerated, or acute.
SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES
Cancer - Silica is listed by IARC and NTP as having sufficient evidence to be a carcinogen in
% VOLATILE BY VOLUME: NA humans and in experimental animals for the carcinogenicity of quartz and cristobalite. The
APPEARANCE AND ODOR: Hazy to clear, odorless liquid. overall IARC evaluation was that crystalline silica inhaled in the form of quartz or cristobalite
BOILING POINT: 100潞C from occupational sources is carcinogenic to humans (group 1).
COEFFICIENT OF WATER/OIL DISTRIBUTION: Not available
Scleroderma - There is evidence that exposure to respirable crystalline silica or silicosis is
EVAPORATION RATE: (N-Butyl Acetate=1) Less than 1
associated with incidence of scleroderma of the lungs.
MELTING POINT: 32潞F (0潞C)
ODOR THRESHOLD: Not available
Tuberculosis - Individuals with silicosis are at risk to develop tuberculosis, if exposed to
PH: 11.7
persons with tuberculosis.
SPECIFIC GRAVITY: 1.32
SOLUBILITY IN WATER: 100%
Nephrotoxicity - Recent studies suggest that exposure to respirable crystalline silica or that the
VAPOR DENSITY: Vapor is water
disease silicosis is associated with the increased incidence of kidney disorders.
VAPOR PRESSURE: Vapor is water
ADDITIONAL INFORMATION: Fluoride-the acute lethal oral toxicity for rats is about 125 mg/kg
or body weight. This is equivalent to about 6.5 gms for the average human.
SECTION 10. STABILITY AND REACTIVITY
EYE IRRITANT: Yes
INGESTION IRRITANT: Yes
CONDITIONS TO AVOID: Flammable hydrogen gas may be produced on prolonged contact INHALATION IRRITANT: Yes
with metals such as aluminum, tin, lead, and zinc. RESPIRATORY SENSITIZER: No
HAZARDOUS DECOMPOSITION PRODUCTS: Not known SKIN IRRITANT: Yes
HAZARDOUS POLYMERIZATION: Will not occur. SKIN SENSITIZER: No
CONDITIONS TO AVOID: NA
INCOMPATIBILITY: (Materials to avoid) Acids, salts, or alcohols may cause gel formation (non-
hazardous)
STABILITY: Stable
12 of 16 5 of 16
MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part A, Powder Filler) (Part B, Liquid Binder)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 6. ACCIDENTAL RELEASE MEASURES
SECTION 12. ECOLOGICAL INFORMATION
CLEAN-UP PROCEDURE: Spill area may become slippery; use care to avoid falls. Flush spill
Crystalline silica (quartz) is not known to be an environmental hazard.
area with plenty of water. For spill quantities greater than 100 gallons: isolate, dike and store
Fluorides can be toxic to aquatic and terrestrial flora and fauna.
discharge material, if possible. Otherwise, disperse and flush with water. Observe environmental
regulations.
SECTION 13. DISPOSAL CONSIDERATIONS
SECTION 7. HANDLING AND STORAGE
WASTE DISPOSAL: Sweep up excess; flush area with large quantities of water. Material could
be disposed of in approved landfill according to Federal, state, and local regulations.
Avoid contact with eyes, skin, and clothing.
EUROPEAN COMMUNITY WASTE DISPOSAL KEY: Not known
For industrial use only!
UNCLEANED PACKAGINGS: Disposal must be made according to official regulations.
Do not take internally.
May cause irritation.
SECTION 14. TRANSPORT INFORMATION Wear chemical splash goggles, gloves, and protective clothing.
Wash thoroughly after handling.
DOT I.D. NO.: NOT REGULATED
Store in a cool, dry place.
DOT SHIPPING NAME: HIGH TEMPERATURE BONDING MORTAR
Keep container closed when not in use.
DOT HAZARD CLASS: NOT REGULATED
DOT LABEL: NONE
OTHER: NA
SECTION 15. REGULATORY INFORMATION
U.S. FEDERAL REGULATIONS:
TSCA Status:
Components are included in the EPA Toxic Substances Control Act (TSCA) Chemical
Substances Inventory.
SARA TITLE III:
Section 302 Extremely Hazardous Substances: None above detection limits.
Section 311/312 (40 CFR 370) Hazardous Categories:
Acute
Carcinogen
Chronic
Irritant
Section 313: Toxic Categories (40 CFR 370)Toxic chemicals above 鈥淒e Minimis鈥? level are:
There are no listed chemicals above detection limits in this compound.
CERCLA: The RQ for release of sodium silicofluoride is 1,000 pounds.
6 of 16 11 of 16
MATERIAL SAFETY DATASHEET 7MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part B, Liquid Binder) (Part A, Powder Filler)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 4. FIRST AID MEASURES SECTION 15. REGULATORY INFORMATION (CONT'D)
EYE CONTACT: Flush eyes immediately with water or physiological saline for at least 15 STATE REGULATIONS:
minutes while lifting upper and lower lids. Seek medical attention. California: Proposition 65 substances (components) known to the State of California to cause
cancer and reproductive toxicity and subject to warning and discharge requirements under the
INGESTION: If swallowed, do not induce vomiting. Give large quantities of water. Seek medical 鈥淪afe Drinking Act of 1986鈥?.
attention. Never give anything by mouth to an unconscious person. It has not been determined and cannot be ascertained that this product would not expose users
to the listed chemicals at the very low levels prescribed in the regulations. Therefore, it is the
INHALATION: Not expected to be a problem. user's responsibility to determine if the percent of hazardous/carcinogenic ingredients listed
elsewhere in the MSDS comply with State of California regulations. This product has been
SKIN CONTACT: Wash contact area thoroughly with soap and water. Remove contaminated classified in accordance with the hazard criteia of the Controlled Products Regulations (CPR)
clothing. Launder before reuse. Seek medical attention if erythema develops. and the MSDS contains all the information required by CPR.
CANADA
SECTION 5. FIRE FIGHTING MEASURES DSL: Components included on inventory.
WHMIS HAZARD CLASS (ES):
AUTO IGNITION TEMPERATURE: NA
Class D, Division 2, Subdivision A: Materials cause other toxic effects, very toxic material.
EXPLOSION DATA - Not sensitive to mechanical impact or static discharge.
WHMIS TRADE SECRET REGISTRY NUMBER(S): Not Applicable
EXTINGUISHING MEDIA: NA
WHMIS SYMBOLS:
Stylized T
NOTE: Many dusts and aerosols may exhibit explosive characteristics if ignited by static
discharge or spark. Exercise care to avoid causing dusting or misting.
EUROPEAN ECONOMIC COMMUNITY (EEC)
NOTE: Many dusts and aerosols may exhibit explosive characteristics if ignited by static
EINECS Inventory: Components included on inventory
discharge or spark. Exercise care to avoid causing dusting or misting.
EEC SYMBOL(S):
FIRE AND EXPLOSION HAZARDS: NA
Toxic
Irritant
FIRE FIGHTING PROCEDURES: NA
Harmful
FLAMMABILITY - Not flammable in presence of open flame, sparks, excessive heat and static
EEC RISK庐 PHRASES:
discharge.
Toxic by inhalation and if swallowed
Irritating to eyes, respiratory system, and skin
FLAMMABLE LIMITS LEL: NA
HARMFUL: Danger of serious damage to health by prolonged exposure
FLAMMABLE LIMITS UEL: NA
EEC SAFETY PHRASES
FLASHPOINT: NA
Avoid contact with skin and eyes
Wear suitable protective clothing, gloves, and eye and face protection
Keep container tightly closed and dry
10 of 16 7 of 16
MATERIAL SAFETY DATASHEET MATERIAL SAFETY DATASHEET
MSDS-0103 MSDS-0103
CC High Temperature Cement CC High Temperature Cement
(Part A, Powder Filler) (Part B, Liquid Binder)
One Omega Drive One Omega Drive
Rev. Date 09/05 Rev. Date 09/05
Stamford, CT 06907-0047 Stamford, CT 06907-0047
Supersedes: 07/02 Supersedes: 07/02
omega.com omega.com
e-mail: info@omega.com e-mail: info@omega.com
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
SSECTION 16. OTHER INFORMATION
PRODUCT NAME: CC High Temperature Cement, Part B, Liquid Binder
This MSDS contains information and recommendations based upon our present knowledge and
data believed to be reliable. All data shown here are subject to reasonable variation and are SUPPLIER: OMEGA Engineering, Inc.
supplied as an accommodation to the buyer. However, this shall not constitute a guarantee for ADDRESS: PO Box 4047
any specific product features and shall not establish a legally valid contractual relationship. This Stamford, CT 06907
MSDS applies only to the product in its 鈥渁s manufactured鈥? state, since the application to which TELEPHONE: (203) 359-1660
the product is subjected may change its characteristics. The buyer is responsible for
determining the safety, toxicity, and suitability of the product under the conditions of their use of ITEM NUMBER: CC High Temperature Cement, Part B, Liquid Binder
the product. Buyers also have the responsibility for insuring that the MSDS is available to their ITEM DESCRIPTION: Low Expansion Cement (Liquid)
employees, product users, and handlers. PRODUCT DESCRIPTION: Low Expansion Cement (Liquid)
CHEMICAL FAMILY: Sodium Silicate Solution; aS:O2bNa2O
NAV = Not Available NE = Not Established NA = Not Applicable REVISION DATE: 02/06/02
PRODUCT USE: High temperature bonding/adhesive compounds
SECTION 2. COMPOSITION AND DATA ON COMPONENTS
COMPONENT CAS # ACGIH TLV OSHA PEL % WT
SODIUM SILICATE 1344-09-8 NE NE <50%
NOTES: Exposure values shown for guidance only. Please follow applicable regulations.
SECTION 3. HAZARDS IDENTIFICATION
HMIS rating
Health 2
Flammability 0
Reactivity 0
Personal protection B
THRESHOLD LIMIT VALUE: NE
EFFECTS OF OVEREXPOSURE: Causes irritation to skin, eyes, respiratory tract, esophagus,
and stomach. No known chronic hazards.
INHALATION: Causes sneezing, and burning or itching in nose and throat
EYE EXPOSURE: Pain, redness, and tearing
SKIN EXPOSURE: Itching or burning
8 of 16 9 of 16
|