MSDS No.: 103C
Revision No.: 002
Revision Date: 01/19/2006
庐 Page: 1 of 2
Hilti (Canada) Corporation
MATERIAL SAFETY DATA SHEET
Product identifier: CFR-1 Cleaner
Aerosol solvent for Ccleaning agent for Hilti CF 120 P-2foam dispensers.
Product use:
Hilti (Canada) Corporation, 6790 Century Avenue, Suite #300, Mississauga, Ontario L5N 2V8
Supplier:
Hilti, Inc., P. O. Box 21148, Tulsa, Oklahoma, USA 74121
Originator
Emergency number: Chem-Trec: 1 800 424 9300
HAZARDOUS INGREDIENTS
Ingredient CAS Number % (wt.) LC50, (rat) LD50 (rat) TLV STEL
50,100 mg/m3 / 8Hr.
Acetone 067-64-1 40 鈥? 45 5800 mg/kg 750 ppm 1000 ppm
2-Propanol 067-63-0 30 鈥? 35 16,000 ppm / 8Hr. 5045 mg/kg 400 ppm 500 ppm
3
Butane 106-97-8 10 鈥? 15 65,800 mg/m / 4Hr. N/Av 800 ppm N/E
Propane 074-98-6 10 鈥? 15 N/Av N/Av 2500 ppm N/E
PHYSICAL PROPERTIES
Clear aerosol. Alcohol odour.
Appearance / Physical state: Odour:
0.72 N/Avn/av
Specific gravity (at 20潞C): Odour threshold:
N/Avn/av approx. 2 (air = 1)
Vapour pressure (at 20潞C): Vapour density:
> 3 (n-butyl acetate = 1) N/Avn/av
Evaporation rate: Boiling point:
N/Avn/av N/Avn/av
Freezing point: pH:
N/Avn/av Negligible
Coefficient of H20 / oil distrib: Solubility in water:
FIRE AND EXPLOSION DATA
-20 C / -4 F LFL: 1.4%; UFL:
Flash point / Method: Flammable limits:
12.8%1.4 鈥? 12.8%
Extremely flammable aerosol. N/Avn/av
Conditions of flammability: Auto-ignition temperature:
Dry chemical, foam, CO2, water.
Means of extinction:
Containers can explode or be propelled through the air when exposed to extreme heat such as
Special fire fighting
fire.
procedures:
Thermal decomposition can yield oxides of carbon.Refer to 鈥淗azardous decomposition
Hazardous combustion
products鈥? (next section).
products:
Susceptible to static discharge.
Sensitivity to mechanical
impact / static discharge:
REACTIVITY DATA
Stable. None known.
Stability: Conditions of reactivity:
Strong oxidizers and acids.
Incompatible materials:
None known. Thermal decomposition can yield oxides of carbon.
Hazardous decomposition
products:
TOXICOLOGICAL PROPERTIES
Skin contact Skin absorption Eye contact Inhalation Ingestion
Routes of exposure:
See 鈥淚ngredients鈥? section above.ACGIH-TLV Acetone 750 ppm, 1780 mg/m3 TWA, 1000 ppm
Exposure limits:
2380 mg/m3 STEL/Ceiling, 2-Propanol (Isopropyl alcohol) 400 ppm, 983 mg/m3 TWA, 500 ppm,
1230 mg/m3 STEL/Ceiling, Butane 800 ppm, 1900 mg/m3 TWA
Acute effects of exposure: Eyes: - Irritation and corneal burns can occur from direct contact with the eyes. Skin: -
Prolonged or repeated skin contact can cause irritation and defatting (drying) of the skin.
Inhalation: - Can be irritating to the respiratory tract if inhaled. Headaches and dizziness can
occur from exposure in poorly ventilated areas. Ingestion: - Not likely a likely route of
entryexposure. Harmful if swallowed.
Not applicable.
Chronic effects of exposure:
HILTI 庐 is a registered trademark of Hilti Corp.
None known
Synergistic materials:
FIRST AID MEASURES
Flush with plenty of water for at least 15 minutes. Get medical attention immediately.
Eyes:
Wash skin with mild soap and water. Rinse thoroughly. See a doctor if irritation persists.
Skin:
Remove victim to fresh air. Call physician if ill effects occur.
Inhalation:
If conscious give plenty of water to drink. Never give anything by mouth to an unconscious
Ingestion:
person. Seek medical attention. Do not induce vomiting unless directed to do so by a
physician.
Referral to a physician is recommended if there is any question about the seriousness of the
Other:
injury/exposure.
CONTROL MEASURES AND PERSONAL PROTECTIVE EQUIPMENT
General (natural or mechanically induced fresh air movements).
Engineering controls:
Chemical splash goggles are recommended. Safety glasses with side shields as a minimum.
Eye protection:
Gloves are recommended when cleaning tools (cloth or impermeable).
Skin protection:
None normally required. A NIOSH-approved respirator can be used for protection from mists.
Respiratory protection:
No additional measures are normally required.
Other:
PRECAUTIONS FOR SAFE HANDLING AND USE
Avoid contact with eyes, skin or clothing. Use with adequate ventilation. Wash thoroughly after
Handling procedures and
handling. Keep away from heat, sparks and flames. Do not puncture or incinerate container.
equipment:
Store in a cool dry area. Do not expose to heat or store at temperatures above 49C (120F).
Storage requirements:
Store indoors out of direct sunlight. Keep out of reach of children.
Remove all sources of ignition. Remove spillage with absorbent material. Place in closed
Spill, leak or release:
containers for disposal.
Consult federal, provincial and local regulations for allowed means of disposal.
Waste disposal:
TDG - Aerosols, Flammable, Class 2.1, UN1950, IATA/ICAO - Aerosols, Class 2.1, UN1950,
Special shipping instructions:
Ltd. Qty., IMDG - Aerosols, Class 2.1, UN1950
REGULATORY INFORMATION
A, B5, D2B
WHMIS classification:
Health 1, Flammability 3, Reactivity 0, PPE A (Goggles)
HMIS codes:
Aerosols, Flammable, Class 2.1, UN1950
TDG shipping name:
PREPARATION INFORMATION / CONTACTS
Hilti, Inc., Tulsa, OK USA 1 800 424 9300
Prepared by: Emergency phone number:
Hilti (Canada) Corporation, Mississauga, Ontario; 1 800 363 4458
Customer Service:
Hilti, Inc., Tulsa, OK USA; 1 800 879 6000, Jerry Metcalf (x6704)
Health / Safety contacts:
Abbreviations used: N/E = None Established. N/A = Not Applicable. N/Av = Not Available. H = Hours. HMIS:
Hazardous Materials Identification System
The information and recommendations contained herein are based upon data believed to be correct; however, no guarantee or
warranty of any kind expressed or implied is made with respect to the information provided.
MSDS 103C, Page 2 of 2
|