PRODUCT DATA SHEET
511 Look Penetrating Sealer
Porous Plus
Natural www.miraclesealants.com
Water, Stain & Slip Protection for Grout Sealing
I Grout I Flamed, Honed & Polished Limestone Once the area has completely dried, proceed with the sealing of the grout for water
I Flamed, Honed & Polished Granite and stain resistance. Apply 511 Porous Plus to all grout with a paint brush. Any
I Flamed, Honed & Polished Marble excess sealer that gets on the surface should be wiped off with a clean towel before
I Saltillo Tile I Terra Cotta Pavers I Masonry it dries. On larger jobs grout can be sealed by retreating the entire area including the
I Sandstone I Porous Slate & Brick I Cement tile or stone surface a second time. Be careful not to allow the sealer to puddle or dry
I Concrete I Cantera/Adoquin I Flagstone on presealed surfaces.
I Sanded Grout I Stucco
Residue Removal
Uses To remove accumulated 511 Porous Plus residue, use Miracle Residue Remover as
I Interior & Exterior I Kitchens I Showers directed.
I Restrooms I Patios I Drive Ways
Existing Installation - Surface Preparation
I Garages I Pool Areas I Walls
Surface must be dry and free of contaminants, including previously applied sealers,
Special Features dirt, lime & hard water deposits, efflorescence, rust & other heavy dirt and grime.
I Water Resistant I Stain Resistant I Weather Resistant
Floor Coating/Wax Removal: To remove existing coatings and/or waxes, use Mira
I Acid Resistant I Salt Resistant I Freeze/Thaw Resistant
Strip or H2O Strip following the instructions carefully.
I Slip Resistant I Easy To Use I Low Toxicity
I Non Yellowing I Non coating I U.V. Transparent Heavy Duty Cleaning: To remove lime and hard water deposits, efflorescence, rust,
grease and other heavy dirt and grime use GCFR (Grout & Concrete Film Remover),
Phosphoric Acid Cleaner as directed. For a non-acid deep clean use Liquid Poultice
PRODUCT DESCRIPTION
as directed. All strippers and/or cleaners should be thoroughly rinsed with clean
KEEP OUT OF REACH OF CHILDREN. This product is formulated for sealing concrete water and the surface allowed to dry.
and masonry to provide resistance against water, alkalis, acids, ultraviolet light, stain-
ing, salt ion intrusion and freeze/thaw damage. 511 Porous Plus is a unique formula- Sealing Existing Surfaces: Follow the application instructions previously mentioned,
tion designed for the protection of all porous tile, stone and grout surfaces. 511 except now, seal the grout and tile or stone surfaces at the same time. When treating
Porous Plus penetrates into the surface and forms an invisible barrier that is resis- surfaces together, make sure that the recessed grout is saturated.
tant to moisture and stains, while allowing vapor to escape. 511 Porous Plus is not a
Light Cleaning: Use Mira Clean #1, Porcelain & Ceramic Tile Cleaner, Mira Soap &
surface coating and will not alter the natural look. All surfaces are harder and less
Counter Kleen as directed.
slippery. 511 Porous Plus can be used on interior and exterior applications. 511
Porous Plus is U.V. transparent, resists acid rain and will not yellow under any cir- Sealer Cure Time
cumstances. 511 Porous Plus averages 2 to 10 times the coverage of competitive 511 Porous Plus will be dry to the touch in 1 - 3 hours and may be used for normal
products. (See coverage chart). 511 products have been formulated for or applied to foot traffic. For optimum results the area should be kept dry and free from staining
freshly poured concrete to retard the evaporation of water. materials for 24 - 72 hours.
511 Porous Plus is on the approved sources list of the United States Postal Service Coverage Chart - used as directed
and is U.S.D.A. approved for incidental food contact in federal meat and poultry Material Cost per 500 sq.ft. 1000 sq.ft. 1500 sq.ft. 2000 sq.ft.
establishments. sq.ft/sq.m. 45 sq.m. 90 sq.m. 135 sq.m. 180 sq.m.
Test Data Sanded Grout (.15-.28)
Limestone (.15-.28)
Independent laboratory tests show 511 Porous Plus out performs Saltillo (.15-.45)
competitive products. Test results are available upon request for Staining, Static Sand Stone (.15-.28)
Flag Stone (.15-.28)
Coefficient of Friction, Tabor Abrasion, Surface Absorption, Freeze/Thaw, and Vapor
Flamed Granite (.15-.28)
Transmission. Textured Marble (.15-.28)
Brick (.15-.28)
NOTE: For any questions concerning grout - refer to the grout Concrete (.15-.45)
manufacturers specifications. 511 Porous Plus will not stop acid etching. Stucco (.22-.45)
Slate (.15-.28)
Sample Testing Terra Cotta (.15-.45)
Cantera/Adoquin (.15-.45)
Due to the differences of each substrate, several inconspicuous test patches should Masonry (.15-.45)
be completed to assure maximum performance. User must determine suitability of
Polished Stone Cost per sq. ft/3000-4000 sq.ft. (.05 - .07)
the product for their intended use.
Cost per sq.ft. is based on a suggested list price of $235/gallon. 1 gallon = 3.785 liters.
Color and Gloss Enhancement
For added color with "Textured and Non polished" surfaces, 511 Seal & Enhance or MAINTENANCE
Mira Matte may be used. For polished marble, travertine, limestone and granite,
For ongoing maintenance instructions please refer to Miracle Sealants Care Guide.
Stone Polish, Mira Dust, Marble Conditioner, MiraPolish or Granite Brite may be
Refer to the Miracle Sealants Product Recommendation Chart for specific product
used as directed. For ceramic tile, Tile Restor or Tile Brite may be used as directed.
recommendations.
Protect Neighboring Surfaces
Storage
Always protect neighboring surfaces including wood, carpet, metal , landscaping and
Store 511 Porous Plus in the original container, properly sealed to avoid contamina-
other non masonry surfaces.
tion and solvent evaporation. Stored at 770 F (400 C), 511 Porous Plus will have a shelf
life of 12 months.
N E W I N STA L L AT I O N S - A P P L I C AT I O N I N ST R U C T I O N S
Technical Support
Read entire label and PDS/MSDS before using. 511 Porous Plus should not be
diluted or thinned in any way. 511 Porous Plus should be used as is direct from For additional technical support, contact Miracle Sealants Company at
approved container. 1-800-350-1901 or 626-443-6433 ext. 3013
Office Hours
Sealing As a Grout Release
Monday - Friday from 8:30 am - 5:00 pm PT.
Apply 511 Porous Plus to all surfaces prior to grouting. This step will allow quick and
1-626-443-6433 1-800-350-1901 ?Fax: 1-626-443-1435
easy cleanup after grouting. Grout can stain many surfaces if this procedure is not
website: www.miraclesealants.com
used prior to the grouting process. Apply 511 Porous Plus using a Mira Brush or a
clean towel. Apply enough to wet the surface. (See coverage charts) Be careful not to Product Damaged During Transportation
saturate the open grout joints. Allow 511 Porous Plus to stand for approximately 3 - 5
If product is damaged during transportation contact
minutes for maximum penetration. Any excess sealer remaining at this time should
Info Trac @ 1-800-535-5053
be removed by wiping the surface with a clean dry towel. On very porous surfaces
apply another application after the previous application has dried 2-3 hours. Any Additional Products
excess sealer that has dried on the surface creating a residue/film, may be removed Miracle Sealants Company offers a complete line of water & stain repellents, sealers,
by applying Residue Remover. Apply Residue Remover undiluted to the affected area cleaners, polishing compounds, diamond abrasives, machinery and accessories for
with a clean dry towel. Let it sit for 1 - 2 minutes before buffing the area with a second the tile, stone, concrete, metal, fabric and carpet professional or do-it-yourself spe-
clean dry towel. Allow 511 Porous Plus to cure for 6 - 12 hours before continuing with cialist
the grouting procedure per manufacturers specification.
After Grouting: Once grouted, make sure that all grout residue is removed from the
surface with a clean sponge and water. Allow grout to dry at least 24 - 72 hours.
If grout clean up is not performed effectively, an additional cleaning may be neces-
sary to remove remaining grout residue or haze. For this procedure use Phosphoric
Acid Cleaner , (GCFR) Grout & Concrete Film Remover (Hydrochloric Acid), Sulfamic
Acid Crystals or Epoxy Grout Film Remover following the instructions carefully.
12-2009
MATERIAL SAFETY DATA SHEET
511 Look Penetrating Sealer
Porous Plus
Natural www.miraclesealants.com
Osha's Hazard Communication Standard Symptoms can include but are not limited to irritation of respiratory track,
U.S. Department Of Labor dizziness and light headaches.
29 CFR 1910.1200 OMB No. 1218-0072 Emergency and First Aid Procedures:
Eyes: Flush with water for 15 minutes. If irritation persists, call physician.
Identity No: Name: 511 Porous Plus
Skin: Wash with soap and water. If irritation persists, call physician.
Section 1 Ingestion: Do not induce vomiting. Call physician. Keep victim's head below
Manufacturers Name: Miracle Sealants Company hips to prevent aspiration.
Address: 12318 Lower Azusa Road Inhalation: Get person to fresh air. If unconscious, call a physician.
Emergency Phone: 800-350-1901 Section 7 - Precautions For Safe Handling And Use
City: Arcadia
Steps to be taken in case material is released or spilled: soak up with inert,
State: CA
absorbent material. Scoop up and place in a proper disposal container.
Phone: 626-443-6433
Date Prepared 12-2009 Waste disposal method: dispose of in accordance with state and local
regulations.
Section 2 - Hazardous Ingredients/Identity Information
Hazardous Components CAS# OSHA PEL ACGIH TLV Precautions to be taken in handling and storing: store in a cool, dry place
out of direct sunlight. Do not freeze or heat above 1100 f
Petroleum Distillate 64741-65-7 100ppm 150ppm
Butyl Acetate 123-86-4 150ppm 150ppm Other precautions: KEEP OUT OF REACH OF CHILDREN. Follow directions on
N-Heptane 142-82-5 500ppm 400ppm the container for proper use of this product.
Ethyl Acetate 141-78-6 400ppm 400ppm
Section 8 - Control Measures
VOC: Less than or equal to 742 g/L
Respiratory protection: Ventilate by opening all doors and windows. If
Section 3 - Physical/Chemical Characteristics exposure above the TLV or PEL require a NIOSH approved respirator
equipped for the exposure or suitable respiratory protection per
Boiling Point: 3200 F Specific Gravity: 0.80
29 CFR 1910.134 is required.
Vapor Pressure: Not Tested Melting Point: Not Tested
Vapor Density: Not Tested Evaporation Rate: Not Tested Ventilation
Solubility In Water: Insoluble Local Exhaust - Recommended Special - None
Mechanical - Recommended Other - None
Appearance and Odor: Colorless, Solvent Odor
Protective gloves: Rubber or plastic, chemical resistant.
Section 4 - Fire And Explosion Hazard Data
Eye protection: Tight fitting, splash proof safety glasses or goggles.
Flash Point: 1450 F Flammable Limits: Not Tested Other protective clothing or equipment: Chemical resistant clothing.
LEL: Not Tested UEL: Not Tested
pH: Neutral DOT#: Not Available Work hygienic practices: Wash hands thoroughly before handling food
NFPA Hazard Rating H F R S (0-Least, 4-Extreme): 1 2 0 0 stuffs, liquids or tobacco products. Use common sense and care around
chemicals. Never mix this product with other chemicals. Consult your super-
Extinguishing media: CO2, Dry foam visor for all other hygienic and safety practices. All practices depend on
Special fire fighting procedures: Combustible - wear full bunker gear and your specific business. Directions for use normally found on label which will
NIOSH approved breathing apparatus. dictate engineering and control measures.
Unusual fire and explosion hazards: cool exposed containers with water to Section 9 - Shipping & Regulatory Classification
prevent rupturing. Heat will cause phosgene gas.
DOT Shipping Name: Please refer to the Bill of Lading receiving/documents
Section 5 - Reactivity Data for up-to-date information.
Stability: Stable DOT Hazard Class: N/A
Conditions to avoid: Keep away from heat, flame & sparks OSHA Hazard Class: N/A
Incompatible materials to avoid: Heat, flames, strong oxidizer UN/NA Number: N/A
Hazardous polymerization: None EPA Hazard Waste: D 001, Ignitible
Hazardous decomposition product: CO2, CO, HF CPSC Classification: Combustible Liquid
Section 6 - Health Hazard Data Transportation Class: 55
Routes of Entry: Toxic Substances Control Act (TSCA): This product and/or all the ingredients
Inhalation - Possible contained in this product have been registered under the Toxic Substances
Skin - Possible Control Act.
Ingestion - Possible
SARA: No SARA 313 chemicals identified.
Health hazards - Same as signs and symptoms of exposure
OSHA Carcinogenicity - None; NTP - None; IARC Monographs - None NOTE: Miracle Sealants believes the data set forth are accurate. Miracle
Sealants makes no warranty with respects thereto and disclaims all liability
Signs and Symptoms of Over Exposure
or reliance thereon. Such data are offered solely for consideration, investi-
Eyes:Burning irritation.
gation and verification. Also, the data set forth is for the concentrated fin-
Skin: Slight irritation, defatting of the skin. Material will place a clear coat-
ished product. All lab samples are for experimental purposes only and used
ing onto skin.
at the customers discretion.
Ingestion: Toxic
Inhalation: Irritation, dizziness, headaches - may cause CNS depression.
Medical conditions aggravated: Same as signs and symptoms of over expo-
sure.
W A R R A N T Y & C AU T I O N S
Warranty Caution
Instructions are a condensed guide and should not be considered com- 511 Porous Plus contains combustible petroleum distillates. All solvents
plete. In the event of failure, the only obligation of Miracle Sealant must be considered toxic and must be used in a well ventilated area. Good
Company shall be to replace such products proven to be defective. Before ventilation means that fresh air is flowing in such a way as to feel a slight
using, user shall determine the suitability of the product for their intended breeze. Open windows and use fans to circulate air. Continue to ventilate
use User assumes all risks and liability whatsoever in connection therein. until vapors are eliminated. Exposure to high vapor concentration must be
Neither seller nor manufacturer shall be liable for any injury or inability to avoided. Inhaling the vapors can be harmful. Keep away from heat and
use this product. open flames. Avoid prolonged contact with skin. Chemical resistant gloves
should be worn at all times. Keep small children and pets out of the area
until product or surface has thoroughly dried. Refer to MSDS for additional
information.
12-2009
|