MATERIAL SAFETY DATA SHEET
1. PRODUCT IDENTIFICATION
Product: BULLDOG/DUREX #TC101 Elastomeric Coating - Top Coat
Product Code: TC101
MSDS Date: 06-01-08
2. COMPANY IDENTIFICATION
Palmer Asphalt Company After Hours Call: CHEMTREC
196 West 5th Street 800-424-9300 (Domestic - No. America)
Bayonne, NJ 07002 703-527-3887 (International)
Emergency Phone # 201-339-0855 (8:00 am - 5:00 pm EST)
3. INGREDIENTS
# Ingredient CAS Reg. # Weight (%) Vapor Pressure mm Occupational Exposure
Hg @ Temp Limits
755.00 mm Hg @ 80oF
1 Aqua Ammonia 1336-21-6 <1.00 ACGIH TWA 25 ppm
0.22 mm Hg @ 68oF
2 Propylene Glycol 57-55-6 1? None established
3 Acrylic Polymers NA 15 ?25 NA NA
10 mg/m3 (dust)
4 Calcium Carbonate 1317-65-3 30 ?40 NA
10 mg/m3 (dust)
5 Zinc Oxide 1314-13-2 1? NA
10 mg/m3 (dust)
6 Titanium Dioxide 13463-67-7 5 ?10 NA
5 mg /m3 TWA
7 Petroleum Based Defoamer Proprietary <1.00 NA
8 Hydroxyethylcellulose 9004-62-0 <2.00 NA None established
760.00 mm Hg @ 68oF
9 Water 7732-18-5 30 ?35 NA
<.01 mmHg @ 20oC
10 Ester-Alcohol 25265-77-4 <2.00 None established
.22mm Hg @ 68o F .2 mg/m3 TWA
11 2-N-Octyl-4-isothiazolin-3-one 26530-20-1 <1.00
Proposition 65 Statement: Certain raw materials used in making this product may contain small amounts of materials as
impurities which are regulated by Propostion 65.
4. PHYSICAL AND CHEMICAL PROPERTIES
Appearance Semi viscous liquid
State Liquid
Odor Characteristic Mild ammonia odor
Vapor Density (Air = 1) Heavier than air
Vapor Pressure No data
Weight per gallon 11.5 ?12.5
2500F
Boiling Point
Solubility in Water Soluble
VOC <100 grams/liter
Evaporation Rate Slower than ether
The physical and chemical data given in Section 4 are typical values for this product and are not intended to be product
specifications.
5. FIRE AND EXPLOSION HAZARD DATA
Flash Point Non-Combustible
Extinguishing agents: Foam, CO2, Dry Chemical, Water fog
Personal Protective Equipment: As in any fire, wear self-contained breathing apparatus (pressure-demand, NIOSH approved
or equivalent) and full protective gear.
MSDS ?06/01/08 ?BULLDOG/DUREX #TC101 Elastomeric Coating - Top Coat - Page 1 of 3
Unusual Fire and Explosion Hazards: Pressure may build up in tightly closed containers exposed to fire which may result in
rupture. Keep containers cooled with water spray. Material can spatter above 100oC/212oF.
6. REACTIVITY DATA
Instability: Material is considered stable. However, avoid temperatures above 177oC/350oF the onset of polymer
decomposition. Thermal decomposition is dependent on time & temperature.
Hazardous Decomposition Products: Thermal decomposition may yield acrylic monomers.
Hazardous Polymerization: Product will not undergo hazardous polymerization.
Incompatibility: None known
7. HEALTH HAZARD DATA
Primary Routes of Exposure: Inhalation - Skin Contact - Eye Contact
Inhalation - Inhalation of vapor or mist can cause the following: irritation of nose, throat and lungs
Eye Contact - Material can cause the following: -slightly irritating to the eyes.
Skin Contact - Prolonged or repeated skin contact can cause the following: -moderate skin irritation ?reddening
Ingestion - Material is harmful if swallowed. Material can cause the following:-gastrointestinal irritation ?nausea ?vomiting ?br>
diarrhea
8. FIRST AID MEASURES
Inhalation - Move subject to fresh air. If breathing is difficult, give oxygen. Give artificial respiration if breathing has stopped.
Get medical attention immediately.
Eye Contact - Immediately flush eyes with a large amount of water for at least 15 minutes. If redness, itching or a burning
sensation develops, see a physician.
Skin Contact - Remove contaminated clothing. Wash affected areas thoroughly with soap and water. Wash contaminated
clothing thoroughly before reuse. If redness, itching or a burning sensation develops, see a physician.
Ingestion - DO NOT induce vomiting. Give milk or water to drink. Get medical attention immediately. If vomiting occurs
spontaneously, keep airway clear.
Note to Physician - No specific antidote, treat symptomatically.
9. ACCIDENTAL RELEASE MEASURES
Personal Protection: Wear compatible, chemically resistant gloves. Wear protective clothing including splash proof goggles
and rubber overshoes.
Procedures: Contain spills immediately with inert materials (e.g. sand, earth). If material is spilled in a confined area ventilate
the area well. Keep spectators away. Floor may be slippery; use care to avoid falling. Transfer liquids and solid diking material
to separate suitable containers for recovery or disposal. Keep spills and cleaning runoffs out of municipal sewers and open
bodies of water.
10. HANDLING & STORAGE
Storage Conditions: Avoid temperature extremes during storage; ambient temperature preferred. Store in well-ventilated area.
Keep container tightly closed when not in use. Keep from freezing. Store material out of direct sun.
Handling Procedures: Use in well-ventilated areas. Keep containers closed when not in use. Keep away from excessive heat
and open flames. Do not work alone! Keep out of reach of children!
Other: Improper disposal or re-use of this container may be dangerous and illegal. Refer to applicable local, state and federal
regulations.
11. EXPOSURE CONTROLS ?PERSONAL PROTECTION
Respiratory Protection: A respiratory protection program meeting OSHA 1910.134 and ANSI Z88.2 requirements or
equivalent must be followed whenever workplace conditions warrant a respirator's use. None required under normal operation
conditions. Approved mechanical filter respirator to remove solid airborne particles of overspray during spray application.
Eye Protection: Use chemical splash goggles or face shield. (ANSI Z87.1 or approved equivalent). Eye protection worn must
be compatible with respiratory protection system employed.
MSDS ?06/01/08 ?BULLDOG/DUREX #TC101 Elastomeric Coating - Top Coat - Page 2 of 3
Hand Protection: Chemical-resistant gloves should be worn whenever this material is handled. Rinse and remove gloves
immediately after use. Wash hands with soap and water.
Other protection: Use chemically resistant apron or other impervious clothing to avoid prolonged or repeated skin contact.
Engineering Controls (Ventilation): Use local exhaust ventilation with a minimum capture velocity of 100ft/min. (.5 m/sec.)
at the point of vapor evolution. Refer to the current edition of Industrial Ventilation: A Manual of Recommended Practice
published by the American Conference of Governmental Industrial Hygienists for information on the design, installation, use,
and maintenance of exhaust systems.
Work ?Hygienic Practices: Remove contaminated clothing; launder or dry clean before reuse. Wash thoroughly with soap
and water.
12. DISPOSAL CONSIDERATIONS
Procedure: Dispose of in accordance with local, state and federal regulations.
13. TRANSPORT INFORMATION
US DOT Class Paint, Not Regulated
14. OTHER INFORMATION
Category HMIS ?TC101 Scale
Toxicity 1 4=Extreme
Fire 0 3=High
Reactivity 0 2=Moderate
Special - 1=Slight
0=Insignificant
Prepared by: Palmer Asphalt Company ?Technical Department
The information contained herein relates only to the specific material identified. Palmer Asphalt Company believes that such
information is accurate and reliable as of the date of this Material Safety Data Sheet, but no representation, guarantee or
warranty, expressed or implied, is made as to the accuracy, reliability, or completeness of the information. Since conditions of
use are out of our control, users assume all risks associated with the use of the material and are advised to confirm in advance
that the information contained in this MSDS is correct, applicable, and suitable to their circumstances. As these are proprietary
formulations, the actual percentages of ingredients have been omitted pursuant to OSHA Federal Hazard Communication
Standard.
PALMER ASPHALT COMPANY
196 WEST 5TH STREET
BAYONNE, NJ 07002
www.palmerasphalt.com
MSDS ?06/01/08 ?BULLDOG/DUREX #TC101 Elastomeric Coating - Top Coat - Page 3 of 3
|