Material Safety Data Sheet
SURE-WHITE LAP SEALANT MSDS No. 302172
Date of Preparation: 4/11/2008 Revision: 015
Section 1 - Chemical Product and Company Identification
Product/Chemical Name: SURE-WHITE LAP SEALANT
General Use: White Lap Sealant
Manufacturer: Carlisle SynTec Incorporated, 1285 Ritner Highway, Carlisle, PA 17013, Phone: 800-479-6832
24 Hour Emergency Phone Number: CHEMTREC (USA) 800-424-9300
Section 2 - Hazards Identification
Emergency Overview
Flammable
Skin and Eye Irritant
Aspiration Hazard
Skin Sensitizer
Medical Conditions Aggravated by Exposure: Pre-existing eye, skin and pulmonary disorders may be aggravated by exposure
to this product.
Primary Route of Entry: Skin absorption Yes
Inhalation Yes
Ingestion Yes
Eye contact Yes
Signs and Symptoms of Exposure:
Skin contact: Can cause redness, irritation, defatting, and dermatitis.
Inhalation: Prolonged inhalation of vapors may cause irritation of the respiratory tract. Intentional misuse by
deliberately concentrating and inhaling vapor may be harmful or fatal.
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, and diarrhea.
Eye Contact: Can cause severe irritation, redness, tearing, blurred vision.
Acute Effects of Overexposure: Irritation, redness
Chronic Effects: (include all potential carcinogens present at 0.1% or greater): None known
Carcinogenicity: NTP: No ARC Monographs: No OSHA regulated: No
Section 3 ?Ingredient Information
Hazardous Ingredients CAS Number % wt
Light Aliphatic Solvent Naphtha 64742-47-8 30-60
Additional Ingredients CAS Number % wt
Section 4 - First Aid Measures
On Skin: Wash with soap and water. Get medical attention if irritation persists.
Inhaled: Remove affected person to fresh air, give oxygen or artificial respiration as necessary to assist breathing.
Get medical attention.
Ingested: Do not induce vomiting. Get medical attention.
In Eyes: Flush with large amounts of water, frequently flushing under the lids. Seek medical attention.
After first aid, get appropriate in-plant, paramedic, or community medical support.
4/11/08 SURE-WHITE LAP SEALANT MSDS No. 302172
Section 5 - Fire-Fighting Measures
Flash Point: 52 癋 (11 癈)
Flash Point Method: Tag closed cup
LEL: 0.9%
UEL: 6.7%
Proper Extinguishing Media: Foam, dry chemical or carbon dioxide. Water may be ineffective, but water should be used to keep
fire-exposed containers cool.
Recommended Firefighting Procedures: Treat as a class "B" fire. Limit firefighting to those trained to do so. If a leak or spill has
ignited, use water spray to disperse the vapors and to protect the men attempting to stop the leak. Minimize breathing gases, vapor,
fumes or decomposition products. Use supplied-air breathing equipment for enclosed or confined spaces or as otherwise needed.
Unusual Fire & Explosion Hazards: Vapors are heavier than air and may travel along the ground and be ignited by ignition
sources distant from the handling point. Residue in "empty" containers may be explosive if exposed to an ignition source, to
prevent fire or explosion from static accumulation and discharge, effectively ground the product transfer system.
Section 6 - Accidental Release Measures
Steps To Be Taken in Case Material is Released or Spilled: Eliminate all ignition sources. Control the source of the spill if it is
safe to do so. Ventilate enclosed areas to prevent vapor accumulation. Restrict access by unauthorized personnel. Absorb spilled
product with vermiculite or other absorbent material. Shovel or scoop into a sealable container for disposal.
Section 7 - Handling and Storage
Storage and Handling Procedures: Do not store or handle near an ignition source. Keep containers closed. Effectively ground
the product transfer system to prevent fire or explosion from static discharge. Empty containers may contain residual product.
Do not reuse containers unless properly reconditioned.
Section 8 - Exposure Controls / Personal Protection
Hazardous Ingredients:
OSHA PEL ACGIH TLV NIOSH REL NIOSH
Ingredient TWA STEL TWA STEL TWA STEL IDLH
Light Aliphatic 500 ppm none estab. 300 ppm none estab. none estab. none estab. none estab.
Solvent Naphtha
Ventilation: General exhaust as needed to keep TLV below recommended levels if engineering or administrative controls are not
adequate.
Personal Protective Equipment
Respirator: For large spills or entry into enclosed small spaces with inadequate ventilation, a pressure demand, self-contained
breathing apparatus is recommended. If engineering or administrative controls are not adequate to maintain solvent TLV below
recommended levels, an appropriate respirator should be used in conjunction with a respirator use and fit training program.
Gloves: Buna-N, if needed
Eye Protection: Safety glasses with side shields if needed.
Other Protective Clothing/Articles: To prevent repeated or prolonged skin contact, wear impervious clothing and boots if contact
is likely.
Work/Hygienic Practices: Minimize breathing vapor. Avoid prolonged or repeated contact with the skin. Remove contaminated
clothing and launder before reuse, Cleanse skin thoroughly after contact, before work breaks and meals and at the end of the
workday. Product is readily removed from the skin with waterless hand cleaners followed by washing thoroughly with soap and
water.
Page 2 of 4
4/11/08 SURE-WHITE LAP SEALANT MSDS No. 302172
Section 9 - Physical and Chemical Properties
Physical State: Paste Water Solubility: <0.5%
Appearance and Odor: White paste with aliphatic Boiling Point(癋): 240 (115癈)
solvent naphtha odor % Volatile: 45
Vapor Pressure: 45 mm Hg at 78 癋 (26 癈) Evaporation Rate (ethyl ether = 1): 9.2
Vapor Density (Air=1): 3.8 Percent Solids (by weight): 55
VOC: 448 gpl
Specific Gravity (H2O=1): 1.16
Flash Point: 52 癋 (11 癈)
Flash Point Method: Tag closed cup
LEL: 0.9%
UEL: 6.7%
Section 10 - Stability and Reactivity
Stability: Stable
Possibility of Hazardous Reactions: Will not occur
Chemical Incompatibilities: None known
Conditions to Avoid: None known
Hazardous Decomposition Products: In the event of partial combustion, fumes, smoke, carbon dioxide, aldehydes and other
decomposition products may be released.
Section 11- Toxicological Information
This product has not been tested. No data available.
Section 12 - Ecological Information
This product has not been tested. No data available.
Section 13 - Disposal Considerations
Waste Disposal Method: If this product becomes a waste, it is considered a hazardous waste due to its ignitability. Dispose of in
accordance with local, state and federal environmental and waste regulations.
Section 14 - Transport Information
DOT Transportation Data (49 CFR 172.101):
Shipping Name: Adhesive, Packaging Authorizations Quantity Limitations
Containing a Flammable Liquid a) Exceptions: 173.150 a) Passenger, Aircraft, or Railcar: 5 L
b) Non-bulk Packaging: 173.173 b) Cargo Aircraft Only: 60 L
Shipping Symbols:
Hazard Class: 3 c) Bulk Packaging: 173.242
ID No.: UN1133 Vessel Stowage Requirements
Packing Group: II a) Vessel Stowage: B
Label: 3 b) Other: None
Special Provisions (172.102):
149, B52, IB2, T4, TP1, TP8
Section 15 - Regulatory Information
All components are included in the EPA Toxic Substance Control Act (TSCA) Chemical Substance Inventory.
If this product becomes a waste, it meets the criteria of a hazardous waste as defined under RCRA 4OCFR261: Ignitability
Hazardous Materials Identification System (HMIS):
Health Hazard Rating: 1 CAUTION Irritation or minor reversible injury possible.
Flammability Hazard Rating: 3 WARNING Material capable of ignition under almost all normal temperature conditions.
Reactivity Hazard Rating: 0 Normally stable and will not react with water.
Personal Protective Equipment B Safety glasses and gloves
Page 3 of 4
4/11/08 SURE-WHITE LAP SEALANT MSDS No. 302172
EPA SARA Title Ill hazard class (40CFR370): Acute Health Hazard
Chronic Health Hazard
Fire Hazard
EPA SARA Title Ill Section 313 (40CFR372): There are no listed toxic chemicals present in quantities greater than the de
minimis level.
EPA SARA Title Ill (40CFR355): There are no components present in this product at a level which would require reporting.
Pennsylvania Right-To-Know:
Substances on the Pennsylvania Hazardous Substances List present at a concentration of 1% or more (0.01% for Special
Hazardous Substances):
Chemical Name CAS #
Titaniun Dioxide 13463-67-7
Naphtha VM&P 64742-47-8
Non-Hazardous Substances at a concentration of 3% or more:
Chemical Name CAS #
Calcium Carbonate 471-34-1
Hydrogenated Hydrocarbon Resin 68132-00-3
Quaternary Ammonium Montmorillonite 68953-58-2
Ethylene Propylene Copolymer 9010-79-1
Ethylene Propylene Terpolymer 25038-36-2
California Proposition 65 (Safe Drinking Water and Toxic Enforcement Act of 1986): This product contains no listed
substances, which the State of California has found to cause cancer, birth defects, or other reproductive harm, in a form which
would require a warning under the statute.
Section 16 - Other Information
Prepared By: Research & Development
Revision Notes: Formatting Changes.
Additional Hazard Rating Systems:
Disclaimer: The information contained in this document is based upon data that was supplied to Carlisle by other
companies and organizations. No warranty of merchantability or fitness for a particular purpose is expressed or implied
regarding the accuracy or completeness of the data and/or information in this material safety data sheet.
Page 4 of 4
|