Material Safety Data Sheet
Premier Implant Cement, Catalyst
Form 70010/B-MSDS, Rev. A
Last revised: 27-Oct-2006
Approved for Use: 27-Oct-2006
---------------------------------------------------------------------------------------------------------------------------
-
1. Chemical product and company identification
Product Name:
Premier Implant Cement
Manufacturer:
Premier Dental Products Co.
1710 Romano Drive
Plymouth Meeting, PA 19462
PH: 610-239-6000 FAX: 610-239-6171
2. Composition / Information on Ingredients
Hazardous Ingredients CAS # Hazard Identification & Risk Phrases
Aliphatic Urethane Diacrilate Resilient Oligomer Proprietary N/E
Triethylenglycoldimethacrylate 109-16-0 Xi
Benzoyl Peroxide 94-36-0 Explosive, Xi
Barium aluminoborosilicate glass 65997-17-3 N/E
Fumed Silica 7631-86-9 R36/37/38
TiO2 13463-67-7 N/E
Pink Pigment 1309-37-1 N/E
3. Hazards Identification
Acute Health Hazards: May cause eye, respiratory and skin irritation in high concentrations.
Chronic Health Hazards: Material is not known to cause significant health problems.
Signs and Symptoms of Exposure: High concentrations can cause eye and respiratory irritation. Prolonged skin
exposure can cause dryness.
Primary routes of exposure: inhalation, skin contact, eye contact
Carcinogenicity: NTP ?no, OSHA ?no, IARC ?no.
4. First Aid Measures
In case of inhalation: If irritation occurs, take victim to open air. If breathing difficulty persists, consult a
physician.
In case of skin contact: Wash with soap and water.
In case of eye contact: Flush with large quantities of water for 15 minutes. Consult a physician.
In case of ingestion: Consult a physician.
5. Fire-Fighting Measures
Flash Point: N/E
Extinguishing Media: Carbon dioxide, water spray, dry chemical
Special Fire Fighting Procedures: Avoid a direct jet of water.
Unusual Fire and Explosion Hazards: None
6. Accidental Release Measures
Environmental Precautions: Avoid seepage into sewers and water supplies.
Clean-Up Procedure: Contain spill and pick up material with a suitable absorbent material. Place absorbent into
a container for later disposal. Clean spill area with detergent and water.
7. Handling and Storage
Handling: No special measures necessary if handled according to instructions.
Storage: Avoid extreme heat. Keep in temperature of about 10篊 in tightly closed container when not in use, away
from heat, light, ignition sources. Keep material in original packaging.
Form 70010/B-MSDS, Rev. A
Page 1 of 3 Pages
8. Exposure Controls / Personal Protection
Exposure Controls: Use only in well-ventilated areas.
Respiratory Protection: Avoid inhalation of vapors. No special protection under normal use.
Hand and Skin Protection: Avoid unnecessary skin contact. Wear latex gloves when handling.
Eye Protection: Wear safety goggles or safety glasses with side shields when handling.
Hygiene Measures: Remove spilled material from skin and clothing. Do not eat or drink when handling this
material.
9. Physical and Chemical Properties
Appearance: Pink paste
Odor: Specific odor
Boiling Point/Range: N/A
Evaporation Rate (Water = 1): N/A
Vapor Density (Air = 1): N/A
Solubility in Water: Insoluble
10. Stability and Reactivity
Stability: This material is stable.
Hazardous Reactions: None if handled according to directions
Hazardous Polymerization: May occur.
Conditions to Avoid: Heat, UV light and contamination.
Incompatibility: Free radicals, reducing agents, heavy metal ions
Hazardous Decomposition Products: Carbon dioxide, water, carbon monoxide, acrylic decomposition products,
depending on conditions of heating and burning.
11. Toxicological Information
Acute oral toxicity : LD50 (rat) > 5000mg/KG
Irritation of Skin: dryness and irritation possible upon prolonged exposure
Allergic Effects: Methacrylate sensitive individuals may exhibit an allergic reaction.
12. Ecological Information
Do not discharge into sewers or water supplies
Environmental persistence and degradability: no data available
Ecotoxicity: no data available
13. Disposal Considerations:
May be disposed of in landfill or incinerator in accordance with local, state and federal regulations.
Form 70010/B-MSDS, Rev. A
Page 2 of 3 Pages
14. Transport Information:
U.S. DOT Shipping Name: Not Regulated
U.S. DOT Hazard Class: None
U.N./N.A. Number: None
U.S. DOT Packing Group: None
Other: Not considered hazardous cargo
15. Regulatory Information:
U.S.-O.S.H.A. Status: This material is not hazardous under the criteria of the U.S. Federal Hazard
Communication Standard.
16. Other Information
Material should be maintained in original containers. Empty containers should not be re-used.
ANSI/NFPA 704 Data:
Fire = 2
Health = 1
Reactivity = 1
Specific Hazard = None
This information is based on data considered accurate. However, no warranty is expressed or implied regarding the
accuracy of these data, or the results to be obtained from use thereof. In no event will the manufacturer or distributor be
responsible for damages of any nature whatsoever resulting from the use of, or reliance upon this information. General
properties described herein are to be regarded as guides and are not guaranteed for all samples.