Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 1 ?PRODUCT IDENTIFICATION
Product Name: Manufacturer's Name:
SEBS Flashing Compound Water Tight Technologies, LLC
Item Number(s): Manufacturer's Address:
BRITE-n-EZ - SEBSF P.O. Box 899, Payson, AZ 85547
24 Hour Emergency Telephone Number: HMIS Acute Hazard Rating:
CHEMTREC ?United States 800-424-9300 ; Health __, Flammability __, Reactivity __
International 202-483-7616 (collect)
Chemical Name/Synonyms: Chemical Family:
N/A Mixture
SECTION 2 ?CHEMICAL COMPOSITION
Ingredient Components (chemical names) Common Names Case No. OSHA ACGIH
Hazardous components 1% or greater PEL-TWA TLV-TWA
%
Carcinogens 0.1% or greater
Toluene* 40 108-88-3 200 ppm 100 ppm
5 mg/m3 5 mg/m3
Titanium Dioxide* 13 13463-67-7
Solvent 64742-95-6 100 ppm N/A
5 mg/m3 5 mg/m3
Calcium Carbonate 1317-65-3
Styrene Butylene Block Copolymer 66070-58-4 NA NA
Zinc Dibutyldithiocarbamate 136-23-2 NA NA
Polyalicyclic Resin 69430-35-9 NA NA
* Indicates toxic chemical subject to the reporting requirements of section 313 of Title III and of 40 CFR 372.
SECTION 3 ?PHYSICAL & CHEMICAL CHARACTERISTICS
Physical State:
Appearance/Odor: Solubility in Water:
Liquid
White mastic, slight solvent odor. Negligible
Boiling Point: Specific Gravity (H睴=1) Melting Point:
1.0 N/A
231?F
Vapor Density: Additional Information: Freezing Point:
Heavier than air Evaporation rate ?slower than ether Not Established
VOC: Ignition Temperature: Reactivity in Water:
3.24 lb/gal. (388 g/L) N/A N/A
BRITE-n-EZTM SEBS Flashing Compound ?Page 1 of 1
January 19, 2009
Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 4- FIRE & EXPLOSION HAZARD DATA
Flash Point: Flammable Limits (in air):
145?F LEL: 1.0%; UEL: 7.0%
Extinguishing Media: Fire Fighting Procedures:
Foam, dry chemical or CO2 extinguisher. Self-contained breathing apparatus with full face piece
operated in pressure demand or other positive pressure
mode. During emergency conditions over exposure to
decomposition products may cause immediate or delayed
health hazards.
Special Fire & Explosion Hazards:
Hazardous Decomposition Products:
Vapors are heavier than air and may travel along the
May form toxic materials, CO2, CO, various
ground and be ignited by heat, open flame, or other
hydrocarbons, etc. on thermal decomposition.
ignition sources. Keep containers tightly closed. Closed
containers may explode when exposed to extreme heat.
Method Used: Auto-Ignition Temperature:
TCC This product is not self-igniting.
SECTION- 5 HEALTH HAZARD DATA
Medical Conditions Aggravated By Exposure: Signs and Symptoms of Exposure:
Excessive inhalation of vapors can cause nasal and
None known. respiratory irritation, dizziness, fatigue, nausea,
headache and possible unconsciousness. Ingestion may
cause gastrointestinal irritation ,nausea, vomiting and
diarrhea. Eye contact may cause redness, tearing and
blurred vision. Repeated skin contact may cause
irritation, defatting and dermatitis.
Acute: Chemical Listed as a Carcinogen (or Potential Carcinogen):
Irritation to eyes, skin, nasal and respiratory irritation.
Eye contact can cause redness and blurred vision. Skin National Toxicology Program: None
contact may cause defatting and dermatitis. Aspiration I.A.R.C. Monographs: Toluene (108-88-3)
into lungs can cause chemical pneumonitis, which can be OSHA: None
fatal.
Chronic:
Prolonged or repeated exposure to levels above TLV may
result in permanent brain and nervous system damage.
Emergency & First Aid Procedures:
Eye Contact:
Flush with water and call physician
Skin Contact:
Clean with soap and water. Remove contaminated clothing.
Inhalation:
Remove to fresh air. Administer oxygen or artificial respiration, if necessary. Call physician.
Ingestion:
Drink 1 ?2 glasses of water to dilute. Do not induce vomiting. Consult a Physician.
Primary Route of Entry:
Inhalation, eyes, skin, ingestion
BRITE-n-EZTM SEBS Flashing Compound ?Page 2 of 2
January 19, 2009
Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 6 ?REACTIVITY DATA
Stability: Incompatibility:
Stable at ambient temperatures and pressures Avoid contact with strong oxidizing agents, strong acids
and selected amine.
Hazardous Decomposition Products: Hazardous Polymerization:
May form toxic materials, CO2, CO, various hydrocarbons, Will not occur
etc. on thermal decomposition.
Conditions to Avoid:
Do not expose to high temperatures, open ignition sources which induce thermal decomposition.
SECTION 7 - SPILL OR LEAK PROCEDURES
Steps to be taken in case material is released or spilled:
Small spill:
Eliminate all ignition sources. Dike, contain or absorb with inert materials (sand, vermiculite, etc). Transfer
containers for recovery or disposal. Prevent runoff into sewers, streams or other bodies of water.
Large Spill:
Eliminate all ignition sources. Dike, contain or absorb with inert materials (sand, vermiculite, etc). Transfer
containers for recovery or disposal. Prevent runoff into sewers, streams or other bodies of water.
Waste Disposal Method:
Dispose of in accordance with federal, state and local regulations. Do not dump into sewers, on the ground or into any
body of water.
SECTION 8 ?SPECIAL PROTECTION
Respiratory Protection: Eye Protection:
If TLV is exceeded use NIOSH/MSHA approved organic
Splash goggles or other OSHA permitted safety glasses.
vapor and mist mask, supplied air or self contained
breathing apparatus, depending on the vapor
concentration in the area. Do not enter area if vapor
concentration exceeds OSHA permissible levels.
Protective Gloves: Other Protective Equipment:
Impervious gloves are recommended to prevent skin Impervious clothing and supply eyewash stations.
contact, i.e. nitrile rubber gloves.
Ventilation:
Use adequate mechanical ventilation to maintain exposure to below TLV.
BRITE-n-EZTM SEBS Flashing Compound ?Page 3 of 3
January 19, 2009
Water Tight Technologies, LLC
P.O. Box 899, Payson, AZ 85547
SECTION 9 ?SPECIAL PRECAUTIONS OR OTHER COMMENTS
Storage/Handling:
Store in cool, dry, well ventilated facility, away from direct sun light. Store and use away from all sources of direct
heat and ignition. Keep containers closed when not in use. DO NOT FREEZE.
Other Precautions:
Provide adequate ventilation and avoid prolonged or repeated contact with the skin. Wash with soap and water after
contact. Vapors of this product are heavier than air and will collect in confined areas. Do not take internally. Avoid
breathing vapors.
Work/Hygienic Practices:
Maintain good personal hygiene practices. Wash contaminated clothing before reuse. Do not eat, drink, or smoke in
work areas. Wash exposed skin before eating, drinking, smoking, or applying cosmetics.
SECTION 10 - TRANSPORTATION
Regulatory Agency: Identification Number:
N/A
Labels Required:
Proper Shipping Name:
Not regulated N/A
Hazard Classification: Other Requirements:
N/A
Packing Group:
SECTION 11 ?MISCELLANEOUS INFORMATION
Additional Comments:
This product contains chemicals (Toluene ?CAS# 108-88-3) known to the state of California to cause birth defects or
other reproductive harm
Date of Previous MSDS:
Changes Since Previous MSDS:
Telephone Number for Additional Information:
888-269-2122
DISCLAIMER
The information contained herein is based on data considered accurate which has been obtained from other
companies and organizations. However, no warranty or representation is expressed or implied that the information
is accurate, complete, or representative. Water Tight Technologies, LLC assumes no responsibility for injury to the
buyer, the buyer's employees, or any third persons if reasonable safety procedures are not followed.
BRITE-n-EZTM SEBS Flashing Compound ?Page 4 of 4
January 19, 2009
|