PRODUCT NAME: Epoxy.com #315 BC A 100% SOLIDS EPOXY COATING PART A
HMIS CODES: H F R P
PRODUCT CODE: Epoxy.com #315BC A 110B
SECTION 1: MANUFACTURER IDENTIFICATION
MANUFACTURER'S NAME: Epoxy Systems, Inc.
ADDRESS: 20774 West Pennsylvania Ave
Dunnellon, FL 34431
EMERGENCY NUMBER: 1-800-633-8253 DATE PRINTED: 08/20/08
INFORMATION NUMBER: 1-352-489-1666 PREPARER: K. Fontaine
SECTION 2: HAZARDOUS INGREDIENTS
ACGIH
OSHA PEL TLV WT % CARCINOGEN
HAZARDOUS COMPONENTS CAS NUMBER
Epoxy Resin 25068-38-6 NE NE 45-65 NO
Benzyl Alcohol 100-51-6 NE NE 5-15 NO
Talc 14807-96-6 2 mg/m? 2 mg/m?10-30 NO
Depending on color, one or more of the following may be present:
Titanium Dioxide 13463-67-7 10 mg/m?1-5 NO
Black Iron Oxide 1317-61-9 10 ppm 10 mg/m? <1 NO
Red Iron Oxide 1332-37-2 10 ppm 10 mg/m?1-5 NO
Yellow Iron Oxide 51274-00-1 10 ppm 5 mg/m? <1 NO
Chromium Oxide 1308-38-9 .5 mg/m?.5 mg/m? <1
The exposure limits shown above for pigments are for dust exposure.
They are not known to be hazardous after blended into a liquid. Wet
sanding is suggested to eliminate airborne dust, if product is machined
or ground. The only other exposure limits established for ingredients
of this product apply to nuisance dusts from inert fillers. These
fillers are blended into a liquid and pose no hazard as supplied.
Substances listed are present in concentration of 1% or greater, or
0.1% if cited as a potential Carcinogen in the OSHA hazards
communication standard. Where proprietary ingredient is listed, the
identity is available as provided in 29 CFR 1910.1200.
NE - Not Established
SECTION 3: PHYSICAL/CHEMICAL CHARACTERISTICS
BOILING RANGE Not determined
VAPOR DENSITY Not determined
VAPOR PRESSURE 1 mm Hg @ 200?F
VOC 0.00
SOLUBILITY IN WATER NIL
APPEARANCE AND ODOR Moderately viscous pigmented
liquid with a mild odor
SPECIFIC GRAVITY (H20=1) 1.51
SECTION 4: FIRE AND EXPLOSION HAZARD DATA
FLASH POINT: >200?F
METHOD USED: Closed Cup
FLAMMABLE LIMITS IN AIR BY VOLUME LOWER: Not determined
UPPER: Not determined
EXTINGUISHING MEDIA: Foam, dry chemical CO 2
OSHA FLAMMABILITY CLASSIFICATION: Combustible liquid, Class III A
SECTION 4: FIRE AND EXPLOSION HAZARD DATA (CON'T)
SPECIAL FIRE FIGHTING PROCEDURES: Decomposition and/or products of
combustion may be toxic. Use self contained breathing equipment.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Decomposition and combustion
products may be toxic.
SECTION 5: REACTIVITY DATA
STABILITY: Normally Stable
CONDITIONS TO AVOID: Elevated temperatures.
INCOMPATIBILITY (MATERIALS TO AVOID): Avoid contact with strong
oxidizing agents, strong acids, strong bases. Mixing large
quantities (1 gallon) with amines or epoxy hardeners can cause heat
build-up and hazardous reaction.
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS: Carbon Monoxide, Carbon
Dioxide, Phenolic Derivatives.
HAZARDOUS POLYMERIZATION: Will not occur.
SECTION 6: HEALTH HAZARD DATA
HEALTH RISKS AND SYMPTOMS OF EXPOSURE:
INHALATION: Exposure to vapors at elevated temperatures may cause
irritation to respiratory tract and difficulty breathing.
EYE: May cause irritation to the eyes.
SKIN: A single exposure to the skin is unlikely to result in harm.
SKIN ABSORPTION: Repeated exposure to the skin can cause
sensitization.
INGESTION: Oral toxicity is low. No hazards expected from normal
industrial exposure.
HEALTH HAZARDS (ACUTE AND CHRONIC):
CARCINOGENICITY:
NTP CARCINOGEN: NO IARC MONOGRAPHS: NO OSHA REGULATED: NO
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: Allergy, Eczema,
or skin conditions.
EMERGENCY AND FIRST AID PROCEDURES:
EYES: Flush at once with potable water for at least 15 minutes.
SKIN: Wash with soap and warm water. Remove contaminated clothes.
Wash before reuse. Destroy contaminated shoes.
INGESTION: Not likely to occur in normal handling. Give large
quantities of water and get medical attention.
INHALATION: Remove to fresh air. Administer oxygen if breathing is
difficult.
SECTION 7: PRECAUTIONS FOR SAFE HANDLING AND USE
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Avoid
contact. Soak up with clay or other absorbent material. Place in
covered container for disposal.
WASTE DISPOSAL METHOD: Dispose in an approved incinerator or an
approved landfill.
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORING: Avoid contact.
OTHER PRECAUTIONS: Keep containers tightly closed when not in use.
If mixture of A and B are allowed to remain in the mixing vessel
past the pot life deadline, heat and a strong reaction will result.
Grinding or other abrasive action to cured film may develop Micro
crystalline Silica dust. Wear a dust mask during such operations.
SECTION 8: CONTROL MEASURES
RESPIRATORY PROTECTION: Avoid breathing vapor mist or spray.
VENTILATION: Use with good ventilation.
PROTECTIVE GLOVES: Wear impervious gloves.
EYE PROTECTION: Wear splash-proof chemical goggles.
OTHER PROTECTIVE CLOTHING OR EQUIPMENT: Provide eye fountain and
safety shower.
WORK/HYGIENIC PRACTICES: Practice good industrial hygiene. Wash with
soap and water before eating, smoking, or using the restroom.
SECTION 9: REGULATORY INFORMATION
SARA TITLE III SECTION 313: Unless shown below, this product does not
contain the following toxic chemicals subject to the reporting
requirements of section 313 of the Emergency Planning and Community
Right to Know Act of 1986 and of 40 CFR 372:
CAS # Chemical Name Percent by Weight
1308-38-9 Chromium compound <1%(not in all
formulations)
PROP 65 (CARCINOGEN): Unless shown below, this product does not
contain chemicals known to the state of California to cause cancer.
CAS # Chemical Name Percent by Weight
None
PROP 65 (TERATOGENIC): Unless shown below, this product does not
contain chemicals known to the state of California to cause birth
defects or other reproductive harm.
CAS # Chemical Name Percent by Weight
None
PROP 65 (CARCINOGENIC & TERATOGENIC): Unless shown below, this product
does not contain chemicals known to the state of California to cause
cancer or birth defects or other reproductive harm.
CAS # Chemical Name Percent by Weight
None
HAZARDOUS WASTE INFORMATION: Unless shown below, this product is not a
hazardous waste according to definitions found in CFR-40.
STATE OF MICHIGAN CRITICAL MATERIALS: Unless shown below, this product
does not contain ingredients appearing on the State of Michigan
Critical Materials List.
CAS # Chemical Name Percent by Weight
None
D.O.T. PROPER SHIPPING NAME: Synthetic Resin Liquid
PROPER SHIPPING NAME: Synthetic Resin Liquid
HAZARD CLASS: non-hazardous
UN/NA ID NUMBER:
SECTION 10: DISCLAIMER
Data and recommendations presented herein are based upon our and other
researchers and are believed to be accurate. The products discussed
are distributed without warranty (expressed or implied) and the
customer shall make his own determination of suitability for his
particular purpose.