Sentinella 2 Part Epoxy
MATERIAL SAFETY DATA SHEET
This Material Safety Data Sheet meets or exceeds the requirements of the Canadian
Controlled Product Regulations (WHMIS)
1. Product and Supplier Identification
Sentinella 2 Part Epoxy
Product:
Product Use: Epoxy Coating
Manufacturer: Smart Surface Technology Inc.,
Unit 143 ?14273 Knox Way,
Richmond, B.C., Canada, V6V 2Z7
Telephone: (604) 244-3122
Facsimile: (604) 244-3115
24-Hour Emergency Response Telephone for Transport Emergencies ONLY: +1 (604) 986-4617
2. Composition
Component 1: Part A
LD50 LC50
Component w/w% Exposure
Limits/ACGIH1
5540 mg/kg
7-10 Not available
Diethylene Glycol Not established
(oral/rat),
Monoethyl Ether
lowest value
CAS No 111-90-0
6000 mg/kg
(dermal/rat)
6600 mg/kg
4-6 15000 ppm
Propylene Glycol TLV-TWA:
(oral/rat) (rat/4 hour)
Monomethyl Ether 100 ppm
13-14 g/kg
CAS No 107-98-2 Basis: CNS,
(dermal/rabbit)
irritation
Not available
20-25 Not available
Modified Polyamine Not available
Resin
Not listed
2880 mg/kg
13-15 Not available
Poly (Oxypropylene) Not available
(oral/rat)
Diamine
2090 mg/kg
CAS 9046-10-0
(dermal/rabbit
Not applicable
93-97 Not applicable
Non-Hazardous Not applicable
Ingredients, ingredients
not WHMIS controlled
1
ACGIH: American Conference of Governmental Industrial Hygienists (ACGIH). Exposure limits
may vary from time to time and from one jurisdiction to another. Check with local regulatory
agency for the exposure limits in your area.
Smart Surface Technologies Inc. -1- August 1, 2007
Sentinella 2 Part Epoxy
Component 2: Part B
LD50 LC50
Component w/w% Exposure
Limits/ACGIH1
100 Not applicable
Non-Hazardous Not applicable Not applicable
Ingredients, ingredients
not WHMIS controlled
3. Hazards Identification
Routes of Entry:
Skin Contact: Yes Eye Contact: Yes Ingestion: Yes Inhalation: Yes
Emergency Overview: Corrosive Material. May cause eye and skin burns. Symptoms may be delayed.
Ingestion will cause burns to the mouth, throat, and esophagus. If ingested, this product is an aspiration
hazard. Aspiration into the lungs is serious and may be fatal due to pulmonary edema.
Acute Health Effects: Inhalation: Severely irritating to the upper respiratory tract if inhaled as a mist, or if
product is heated to produce vapours. High concentrations of mists will cause burning of the mucous
membranes, nasal passages and upper respiratory tract. Skin Contact: Corrosive to skin. Causes burns
which may be delayed. Eye Contact: Extremely corrosive to the eyes. Causes immediate burning, but total
effect may be delayed up to 24 hours. Ingestion: If ingested, gastrointestinal upset may occur. Ingestion will
cause burning of the mouth, throat, and upper respiratory tract. Aspiration into the lungs may cause
pulmonary edema, which in severe cases, may cause death.
Chronic Health Effects: Due to the recommendation not have this material contact the skin or eyes, it is
anticipated that there should be no chronic effects. Acute effects may be so severe that prolonged contact is
impossible.
Medical Conditions Aggravated by Exposure: Persons who are pre-disposed to skin problem eye
problems or impaired respiratory function may be more susceptible to the effects of this product.
4. First Aid Measures
Eye Contact: Immediately flush eyes with water for 15 minutes while retracting the eyelids. Irrigation of the
eye should continue while transport to a medical facility is occurring. Care should be taken not to cross
contaminate eyes. Seek immediate medical attention.
Skin Contact: Wash affected area of the body with soap and water for at least 15 minutes to remove
residue. Launder clothing before reuse. If an irritation develops, seek medical attention.
Inhalation: Remove victim to fresh air, and give artificial respiration if breathing has stopped. Oxygen
should only be administered by a trained attendant. Seek immediate medical attention.
Ingestion: Never give anything by mouth if victim is rapidly losing consciousness. Have victim rinse mouth
thoroughly with water. Do not induce vomiting. Dilute contents of stomach with 240 to 300 ml of water. If
vomiting occurs naturally have victim lean forward to reduce risk of aspiration. Seek immediate medical
attention.
5. Fire Fighting Measures
> 100 oC TCC
Flash point:
Not known
Autoignition temperature:
Not available
Lower Explosive Limit:
Not available
Upper Explosion Limit:
Not sensitive.
Sensitivity to Impact:
Smart Surface Technologies Inc. -2- August 1, 2007
Sentinella 2 Part Epoxy
Sensitivity to Static Discharge: Not sensitive.
Oxides of carbon, reactive hydrocarbons
Hazardous Combustion Products:
Extinguishing Media: Carbon dioxide, dry chemical, Foam, or any Class B agent. Use water fog to cool
containers below flash point. Do not use a water stream.
Fire Fighting Instructions: Evacuate area and fight fire from a safe distance or a protected location.
Approach fire from upwind to avoid hazardous vapours and toxic decomposition products. Do not enter
confined fire space without proper personal protection. Use approved positive pressure self-contained
breathing apparatus. If possible, isolate materials not yet involved in the fire, and move containers from fire
area if this can be done without risk, and protect personnel. Otherwise, fire-exposed containers or tanks
should be cooled by application of hose streams and this should begin as soon as possible and should
concentrate on any unwetted portions of the container.
6. Accidental Release Measures
Personal Protection: See Section 8
Environmental Precautions: For small spills, dike to protect from contamination of natural waterways or
sewers.
Cleanup Procedures: Remove all sources of ignition. Absorb onto vermiculite or other suitable absorbent
and place into approved containers for legal disposal.
7. Handling and Storage
Handling Procedures: Avoid any contact with skin or eyes. Avoid inhalation of vapours. Do not pressurize,
cut, weld, braze, solder, grind, drill, or expose containers to heat or sources of ignition. Store in closed
containers in a well ventilated, dry, cool area. If exposed to heat, containers may expand, eventually
exploding. Use good hygiene practices when handling this material. Wash hands before eating, drinking, or
smoking.
Storage: Store away from oxidizers and ignition sources in a well ventilated cool place. Keep container
closed when not in use.
8. Exposure Controls, Personal Protection
Engineering Controls: General ventilation is recommended when using this product. Local exhaust may be
necessary when Threshold Limit Values (TLV's) are exceeded.
Respiratory Protection: Use appropriate respirator protection if there is any potential to exceed the
exposure limits (See Section 2). Determine the appropriate type by consulting the respirator manufacturer.
Skin Protection: Gloves: Impervious rubber, vinyl, or neoprene is recommended. Clothing: Impervious
coveralls or other outer garments.
Eye and Face Protection: Wear eye/face protection such as chemical splash-proof goggles or face shield.
Footwear: Wear foot protection as requires by worksite.
Other: Eye wash station should be located near work area.
Smart Surface Technologies Inc. -3- August 1, 2007
Sentinella 2 Part Epoxy
9. Physical and Chemical Properties
Part A
Opaque liquid Not applicable.
Appearance: Critical Temperature:
Amine Not known
Odour: Relative Density:
No data (water = 1)
Odour Threshold:
11 No data
pH: Partial Coefficient:
> 1 (Air=1) Not determined
Vapour Pressure: Evaporation Rate:
No available (n-butyl acetate =1)
Solubility:
Vapour Density: Not determined
o
Not determined < 250 cps@ 25 C
Freezing Point Viscosity:
120 ?260oC
Boiling Point:
Part B
> 100oC
Liquid
Appearance: Boiling Point:
Odourless Not applicable.
Odour: Critical Temperature:
No data 1 - 1.05
Odour Threshold: Relative Density:
Not applicable (water = 1)
pH:
Not available No data
Vapour Pressure: Partial Coefficient:
Insoluble in water. Not determined
Solubility: Evaporation Rate:
Vapour Density: Not determined (n-butyl acetate =1)
Not determined Not determined
Freezing Point Viscosity:
10. Stability and Reactivity
Chemical Stability and Reactivity: Product is stable under normal conditions.
Incompatibility: Avoid contact with oxidizers. Keep away from heat and sources of ignition.
Hazardous Decomposition Products: Normal combustion produces oxides of carbon and
unidentified hydrocarbons in smoke, ammonia, oxides of nitrogen.
Hazardous Polymerization: Will not occur.
11. Toxicological Information
Acute Exposure: Corrosive Effects! Not all components have LD50's and LC50's listed, however,
it is expected that both components of this product have an LD50 > 5000 mg/kg (rat/oral).
See Section 3.
Chronic Exposure:
See Section 2.
Exposure Limits:
See Section 3.
Irritancy:
None reported.
Sensitization:
None reported
Carcinogenicity:
May cause harm to unborn fetus.
Teratogenicity:
Not reported
Reproductive toxicity:
Not reported
Mutagenicity:
None known.
Synergistic products:
12. Ecological Information
Environmental toxicity: No data available.
Biodegradability: No data available.
Smart Surface Technologies Inc. -4- August 1, 2007
Sentinella 2 Part Epoxy
13. Disposal Considerations
Canadian Environmental Protection Act: All ingredients are listed on the DSL. Dispose
according to all local, provincial and federal requirements.
14. Transport Information
Part A
Canadian Transportation of Dangerous Goods Regulations: AMINES, LIQUID, CORROSIVE,
N.O.S. (Poly(oxypropylene) Diamine), Class 8, UN 2735, PG III
International Air Transport Association (IATA): AMINES, LIQUID, CORROSIVE, N.O.S.
(Poly(oxypropylene) Diamine), Class 8, UN 2735, PG III
International Maritime Organization (IMO): AMINES, LIQUID, CORROSIVE, N.O.S.
(Poly(oxypropylene) Diamine), Class 8, UN 2735, PG III
Part B
Not Regulated by any mode of transport
15. Regulatory Information
Canadian Federal Regulations:
Canadian Environmental Protection Act: All ingredients are on the Domestic Substances List.
WHMIS Classification: Part A: E, D2B, Part B: Not WHMIS Controlled
16. Other Information
Original Preparation Date: August 1, 2007
Prepared by: Kel-Ex Agencies Ltd., P.O. Box 52201, Lynnmour RPO, North Vancouver, BC,
Canada, V7J 3V5
Disclaimer: This Material Safety Data Sheet was prepared in accordance with criteria and
requirements of the Hazardous Products Act and the Controlled Products Regulations using
information provided by the manufacturer and other sources including CCINFO (Chemical
Information published by the Canadian Centre for Occupational Health and Safety). The
information in the Material Safety Data Sheet is offered for your consideration and guidance when
exposed to this product. The data in this MSDS does not apply to use with any other product or in
any other process.
This Material Safety Data Sheet may not be changed, or altered in any way without the
expressed knowledge and permission of Smart Surface Technology Inc.
Latest revision: None
Smart Surface Technologies Inc. -5- August 1, 2007
|