3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
Material Safety Data Sheet
Copyright, 2006, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M(TM) Super Foam Fast 74, Clear, aerosol
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 05/02/2006
Supercedes Date: 12/01/2004
Document Group: 16-6046-3
Product Use:
Intended Use: aerosol foam adhesive
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
NONVOLATILE COMPONENTS - N.J. TRADE SECRET REGISTRY NO. Trade Secret 15 - 25
04499600-6501P
ISOBUTANE 75-28-5 15 - 25
DIMETHYL ETHER 115-10-6 15 - 25
ACETONE 67-64-1 15 - 25
METHYL ACETATE 79-20-9 3- 7
CYCLOHEXANE 110-82-7 1- 5
PETROLEUM NAPHTHA 64742-48-9 1- 5
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: clear, sweet fruity odor
General Physical Form: Gas
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and
flash back. Aerosol container contains flammable material under pressure. May cause chemical eye burns. May cause
target organ effects.
_________________________________________________________________________________________________
Page 1 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Corrosive (Eye Burns): Signs/symptoms may include cloudy appearance of the cornea, chemical burns, severe pain, tearing,
ulcerations, significantly impaired vision or complete loss of vision.
Skin Contact:
Moderate Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness.
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
Intentional concentration and inhalation may be harmful or fatal.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Prolonged or repeated exposure may cause:
Liver Effects: Signs/symptoms may include loss of appetite, weight loss, fatigue, weakness, abdominal tenderness and
jaundice.
Kidney/Bladder Effects: Signs/symptoms may include changes in urine production, abdominal or lower back pain, increased
protein in urine, increased blood urea nitrogen (BUN), blood in urine, and painful urination.
SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention.
Skin Contact: Remove contaminated clothing and shoes. Immediately flush skin with large amounts of water. Get medical
attention. Wash contaminated clothing and clean shoes before reuse.
_________________________________________________________________________________________________
Page 2 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed: Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
No Data Available
Autoignition temperature
-50 篎 [Test Method: Tagliabue Closed Cup]
Flash Point
No Data Available
Flammable Limits - LEL
No Data Available
Flammable Limits - UEL
Class IA Flammable Liquid
OSHA Flammability Classification:
5.2 EXTINGUISHING MEDIA
Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Extremely
flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back. Aerosol
container contains flammable material under pressure.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures: Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by
qualified personnel. Remove all ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-
sparking tools. Ventilate the area with fresh air. Close cylinder. If the cylinder can't be closed, place in a well-ventilated area,
preferably an operating exhaust hood, or if necessary outdoors. Collect the resulting residue containing solution. Dispose of collected
material as soon as possible.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Keep away from heat,
sparks, open flame, pilot lights and other sources of ignition. No smoking while handling this material. Avoid eye contact with
vapors, mists, or spray. Keep out of the reach of children. Vapors may ignite explosively. May cause flash fire. Prevent build-up of
vapors - open all windows and doors. Maintain vapor concentrations below recommended exposure limits. Use only with cross-
ventilation. Without adequate ventilation, vapors may settle in low-lying areas. Keep away from heat, sparks, and open flame. Do not
smoke or ignite matches, lighters, etc.
_________________________________________________________________________________________________
Page 3 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Use with functioning spray booth or local exhaust. Do not use in a confined area or
areas with little or no air movement. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to
below Occupational Exposure Limits and/or control mist, vapor, or spray. If ventilation is not adequate, use respiratory protection
equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields.
8.2.2 Skin Protection
Avoid skin contact. Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure
assessment. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
8.2.3 Respiratory Protection
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with organic vapor cartridges. Consult the current 3M
Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.
8.3 EXPOSURE GUIDELINES
Ingredient Authority Type Limit Additional Information
ACETONE ACGIH TWA 500 ppm Table A4
ACETONE ACGIH STEL 750 ppm Table A4
ACETONE OSHA TWA, Vacated 750 ppm
ACETONE OSHA TWA 1000 ppm Table Z-1
ACETONE OSHA STEL, Vacated 1000 ppm
CYCLOHEXANE ACGIH TWA 100 ppm
CYCLOHEXANE OSHA TWA 300 ppm Table Z-1
DIMETHYL ETHER AIHA TWA 1000 ppm
DIMETHYL ETHER CMRG TWA 1000 ppm
PETROLEUM NAPHTHA 3M TWA 100 ppm
PETROLEUM NAPHTHA CMRG TWA 300 ppm
ISOBUTANE ACGIH TWA 1000 ppm
METHYL ACETATE ACGIH TWA 200 ppm
METHYL ACETATE ACGIH STEL 250 ppm
METHYL ACETATE OSHA TWA 200 ppm Table Z-1A
METHYL ACETATE OSHA STEL 250 ppm Table Z-1A
VAC Vacated PEL:Vacated Permissible Exposure Limits [PEL] are enforced as the OSHA PEL in some states. Check with your local
regulatory agency.
SOURCE OF EXPOSURE LIMIT DATA:
_________________________________________________________________________________________________
Page 4 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
clear, sweet fruity odor
Odor, Color, Grade:
Gas
General Physical Form:
No Data Available
Autoignition temperature
-50 篎 [Test Method: Tagliabue Closed Cup]
Flash Point
No Data Available
Flammable Limits - LEL
No Data Available
Flammable Limits - UEL
2.97 [Ref Std: AIR=1]
Vapor Density
0.718 [Ref Std: WATER=1]
Specific Gravity
No Data Available
pH
No Data Available
Melting point
Nil
Solubility in Water
1.90 [Ref Std: ETHER=1]
Evaporation rate
<=0.1 % weight [Test Method: Calculated]
Hazardous Air Pollutants
Approximately 55 % [Test Method: calculated SCAQMD rule
Volatile Organic Compounds
443.1]
Approximately 79 % weight
Percent volatile
Not Applicable
Viscosity
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable.
Materials and Conditions to Avoid: Heat
Hazardous Polymerization: Hazardous polymerization will not occur.
Hazardous Decomposition or By-Products
Substance Condition
Hydrocarbons During Combustion
Carbon monoxide During Combustion
Carbon dioxide During Combustion
Oxides of Nitrogen During Combustion
SECTION 11: TOXICOLOGICAL INFORMATION
_________________________________________________________________________________________________
Page 5 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: Incinerate in a permitted hazardous waste incinerator. As a disposal alternative, dispose of waste product
in a permitted hazardous waste facility.
The facility should be equipped to handle gaseous waste.
RECYCLE EMPTY AEROSOL CONTAINERS WHERE AVAILABLE.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
ID Number(s):
62-4950-4935-5, 62-4950-4936-3
Please contact the emergency numbers listed on the first page of the MSDS for Transportation Information for this
material.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - Yes Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - Yes
Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient C.A.S. No % by Wt
CYCLOHEXANE 110-82-7 1- 5
_________________________________________________________________________________________________
Page 6 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
This material contains a chemical which requires export notification under TSCA Section 12[b]:
Ingredient (Category if applicable) C.A.S. No Regulation Status
CYCLOHEXANE 110-82-7 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
ACETONE 67-64-1 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
METHYL ACETATE 79-20-9 Toxic Substances Control Act (TSCA) 4 Test Applicable
Rule Chemicals
STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.
INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 3 Flammability: 4 Reactivity: 0 Special Hazards: None
Aerosol Storage Code: 2
National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.
Revision Changes:
Section 16: NFPA hazard classification for health was modified.
_________________________________________________________________________________________________
Page 7 of 8
3M MATERIAL SAFETY DATA SHEET 3M(TM) Super Foam Fast 74, Clear, aerosol 05/02/2006
Copyright was modified.
Section 3: Potential effects from skin contact information was modified.
Section 3: Potential effects from inhalation information was modified.
Section 3: Potential effects from ingestion information was modified.
Section 5: Unusual fire and explosion hazard information was modified.
Section 6: Release measures information was modified.
Section 7: Handling information was modified.
Section 8: Engineering controls information was modified.
Section 8: Eye/face protection phrase was modified.
Section 10: Hazardous decomposition or by-products table was modified.
Section 4: First aid for ingestion (swallowing) - decontamination - was modified.
Section 4: First aid for ingestion (swallowing) - medical assistance - was modified.
Section 2: Ingredient table was modified.
Section 3: Other health effects information was modified.
Section 8: Exposure guidelines ingredient information was modified.
Section 9: Vapor density value was modified.
Section 15: TSCA section 12[b] information was modified.
Section 3: Immediate physical hazard(s) was added.
Section 13: Waste disposal method information was added.
Section 8: Engineering controls comment was deleted.
Section 8: Exposure guideline note was deleted.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.
3M MSDSs are available at www.3M.com
_________________________________________________________________________________________________
Page 8 of 8
|