Transcend (TM) Additive
Material Safety Data Sheet
Arkema Inc.
1 PRODUCT AND COMPANY IDENTIFICATION
EMERGENCY PHONE NUMBERS:
DFO
Chemtrec: (800) 424-9300 (24hrs) or (703) 527-3887
2000 Market Street
Medical: Rocky Mountain Poison Control Center
(866) 767-5089 (24Hrs)
Philadelphia, PA 19103
Information Telephone Numbers Phone Number Available Hrs
Product Information 800-245-5858 8:00 am - 5:30 pm (Eastern)
Product Name Transcend (TM) Additive
Product Synonym(s) Trans-1,2-Dichloroethylene
Chemical Family
Chemical Formula
Chemical Name Trans-1, 2-Dichloroethylene
EPA Reg Num
Product Use Additive
2 COMPOSITION / INFORMATION ON INGREDIENTS
Ingredient Name CAS RegistryNumber Typical Wt. % OSHA
Trans-1,2-dichloroethylene 156-60-5 >99% Y
The substance(s) marked with a "Y" in the OSHA column, are identified as hazardous chemicals according to the
criteria of the OSHA Hazard Communication Standard (29 CFR 1910.1200)
This material is classified as hazardous under Federal OSHA regulation.
The components of this product are all on the TSCA Inventory list.
3 HAZARDS IDENTIFICATION
Emergency Overview
Clear liquid with a pleasant odor
WARNING!
FLAMMABLE LIQUID AND VAPOR.
CAUSES EYE AND SKIN IRRITATION.
MAY CAUSE RESPIRATORY TRACT IRRITATION.
MAY CAUSE CENTRAL NERVOUS SYSTEM EFFECTS
Potential Health Effects
Inhalation and skin contact are expected to be the primary routes of occupational exposure to this material. Based on
single exposure animal tests, it is considered to be slightly toxic if swallowed, practically non-toxic if absorbed through
skin or inhaled, moderately to severely irritating to eyes and slightly irritating to skin. High vapor concentrations may be
irritating to the eyes and respiratory tract, and may result in central nervous system (CNS) effects such as headache,
dizziness, nausea, drowsiness and, in severe exposures, loss of consciousness. Mild to severe lung injury may occur if
this material is drawn into the lungs (aspirated) during swallowing, or during vomiting after swallowing. Symptoms of
injury may include increased breathing and heart rate, coughing and related signs of respiratory distress. Inhalation of
this material may cause an increase in the sensitivity of the heart to adrenaline, which could result in irregular or rapid
heartbeats and reduced heart function. Medical conditions which may be aggravated by exposure to this material
include heart disease or compromised heart function.
Product Code: 04801 Page 1
Revision: 7 Issued: 08 NOV 2004 of 6
Transcend (TM) Additive
Material Safety Data Sheet
Arkema Inc.
4 FIRST AID MEASURES
IF IN EYES, immediately flush with plenty of water for at least 15 minutes. Get medical attention immediately.
IF ON SKIN, immediately flush with plenty of water. Remove contaminated clothing and shoes. Get medical
attention. Wash clothing before reuse. Destroy contaminated shoes.
IF SWALLOWED, do NOT induce vomiting. Give water to drink. Get medical attention immediately. NEVER
GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
IF INHALED, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give
oxygen. Get medical attention.
5 FIRE FIGHTING MEASURES
Fire and Explosive Properties
Auto-Ignition Temperature NE
Flash Point -12 C Flash Point Method
Flammable Limits- Upper 18%
6.7%
Lower
Extinguishing Media
Use water spray, carbon dioxide, foam or dry chemical.
Fire Fighting Instructions
Fire fighters and others who may be exposed to products of combustion should wear full fire fighting turn out
gear (full Bunker Gear) and self-contained breathing apparatus (pressure demand NIOSH approved or
equivalent). Fire fighting equipment should be thoroughly decontaminated after use.
Fire and Explosion Hazards
When burned, the following hazardous products of combustion can occur: Irritating or toxic vapors
6 ACCIDENTAL RELEASE MEASURES
In Case of Spill or Leak
Extinguish or turn off all ignition sources. Ventilate the space involved. Wear appropriate personal protection
equipment as indicated in Section 8 of this MSDS. Contain spill with inert materials. Construct a dike to
prevent spreading. Collect with non-sparking tools to a suitable container. Prevent waterway contamination.
Absorb liquid onto inert absorbent and place in DOT approved drums for disposal. Consult a regulatory
specialist to determine appropriate state or local reporting requirements, for assistance in waste
characterization and/or hazardous waste disposal and other requirements listed in pertinent environmental
permits.
7 HANDLING AND STORAGE
Handling
Do not get in eyes, on skin or clothing. Avoid breathing vapor or mist. Keep container closed. Use only with
adequate ventilation. Wash thoroughly after handling. Use grounding and bonding connection when
transferring material to prevent static discharges, fire or explosion. Keep away from heat, sparks and flames.
Storage
Store in well ventilated area away from heat and sources of ignition such as flame, sparks and static
electricity. Ensure that all storage and handling equipment is properly rated, grounded and installed to satisfy
Product Code: 04801 Page 2
Revision: 7 Issued: 08 NOV 2004 of 6
Transcend (TM) Additive
Material Safety Data Sheet
Arkema Inc.
7 HANDLING AND STORAGE
electrical classification requirements. Static electricity may accumulate and create a fire hazard. All storage
containers, including containers such as drums, cylinders and IBC's, must be bonded and grounded during
filling and emptying operations. Store away from oxidizers and reactive materials. Keep container tightly
closed. Observe all federal, state and local regulations and National Fire Protection Association (NFPA)
Codes which pertain to the specific local conditions of storage and use, including OSHA 29 CFR 1910.106
and NFPA 30, 70, 77, and 497.
8 EXPOSURE CONTROLS / PERSONAL PROTECTION
Engineering Controls
Investigate engineering techniques to reduce exposures below airborne exposure limits. Provide ventilation
if necessary to control exposure levels below airborne exposure limits (see below). If practical, use local
mechanical exhaust ventilation at sources of air contamination such as open process equipment.
Eye / Face Protection
Where there is potential for eye contact, wear chemical goggles and have eye flushing equipment available.
Skin Protection
Wear appropriate chemical resistant protective clothing and chemical resistant gloves to prevent skin
contact. Consult glove manufacturer to determine appropriate type glove material for given application.
Wear face shield and chemical resistant clothing such as a rubber apron when splashing may occur. Rinse
contaminated skin promptly. Wash contaminated clothing and clean protective equipment before reuse.
Wash skin thoroughly after handling.
Respiratory Protection
Avoid breathing vapor or mist. When airborne exposure limits are exceeded (see below), use NIOSH
approved respiratory protection equipment appropriate to the material and/or its components. Consult
respirator manufacturer to determine appropriate type equipment for given application. Observe respirator
use limitations specified by NIOSH or the manufacturer. For emergency and other conditions where
exposure limit may be significantly exceeded, use an approved full face positive-pressure, self-contained
breathing apparatus or positive-pressure airline with auxiliary self-contained air supply. Respiratory
protection programs must comply with 29 CFR ?1910.134.
Airborne Exposure Guidelines for Ingredients
Exposure Limit Value
Trans-1,2-dichloroethylene
ACGIH TWA - 200 ppm
OSHA TWA PEL - 200 ppm (790 mg/m3)
-Only those components with exposure limits are printed in this section.
-Skin contact limits designated with a "Y" above have skin contact effect. Air sampling alone is insufficient to accurately quantitate
exposure. Measures to prevent significant cutaneous absorption may be required.
-ACGIH Sensitizer designator with a value of "Y" above means that exposure to this material may cause allergic reactions.
-WEEL-AIHA Sensitizer designator with a value of "Y" above means that exposure to this material may cause allergic skin reactions.
Product Code: 04801 Page 3
Revision: 7 Issued: 08 NOV 2004 of 6
Transcend (TM) Additive
Material Safety Data Sheet
Arkema Inc.
9 PHYSICAL AND CHEMICAL PROPERTIES
Clear liquid with a pleasant odor
Appearance/Odor
pH NA
Specific Gravity 1.2565
Vapor Pressure 400 mm Hg @ 87 F
Vapor Density 3.34
Melting Point NE
Freezing Point -58 F (-50 C)
Boiling Point 118 F (48 C)
Solubility In Water Slightly
Molecular Weight 96.94
10 STABILITY AND REACTIVITY
Stability
This material is chemically stable under normal and anticipated storage and handling conditions.
Incompatibility
Sodium hydroxide, steam, potassium hydroxide, oxidizing agents.
Hazardous Decomposition Products
Hydrogen chloride gas. Carbon oxides.
11 TOXICOLOGICAL INFORMATION
Toxicological Information
Data on this material and/or its components are summarized below.
Trans-1,2-dichloroethylene
Single exposure (acute) studies indicate that this material is slightly toxic if swallowed (rat LD50 1,235 mg/kg),
practically non-toxic if absorbed through skin (rabbit LD50 >5,000 mg/kg) or inhaled (rat 4-hr LC0 8,000 ppm),
moderately to severely irritating to rabbit eyes and slightly irritating to rabbit skin. No adverse effects were
observed in rats following repeated oral administration. Repeated inhalation produced effects in the liver, lungs
and blood parameters of rats. No malformations in offspring of rats following inhalation during pregnancy; fetal
toxicity was noted at doses that also produced adverse effects on the mothers. Cardiac sensitization was noted
in dogs after exposure by inhalation after exposure to concentrations of 25 - 50% in air. No genetic changes
were observed in tests using bacteria or animal cells or whole animals.
12 ECOLOGICAL INFORMATION
Ecotoxicological Information
Data on this material and/or its components are summarized below.
Trans-1,2-dichloroethylene
Bluegill sunfish 96 hr LC50 = 135 mg/l
Daphnia magna 48 hr LC50 170 - 290 mg/l
Product Code: 04801 Page 4
Revision: 7 Issued: 08 NOV 2004 of 6
Transcend (TM) Additive
Material Safety Data Sheet
Arkema Inc.
12 ECOLOGICAL INFORMATION
Chemical Fate Information
Data on this material and/or its components are summarized below.
Trans-1,2-dichloroethylene
Aerobic biodegradation: 93 - 95 % after 28 day(s); the test material exhibited slow to moderate biodegradative
activity
13 DISPOSAL CONSIDERATIONS
Waste Disposal
Recover, reclaim or recycle when practical. Dispose of in accordance with federal, state and local regulations.
Note: Chemical additions to, processing of, or otherwise altering this material may make this waste
management information incomplete, inaccurate, or otherwise inappropriate. Furthermore, state and local
waste disposal requirements may be more restrictive or otherwise different from federal laws and regulations.
14 TRANSPORT INFORMATION
DOT Name 1,2-Dichloroethylene
DOT Technical Name
DOT Hazard Class 3
UN Number UN1150
DOT Packing Group PG II
RQ 1000 lbs/454 kg (1,2-trans-Dichloroethylene)
15 REGULATORY INFORMATION
Hazard Categories Under Criteria of SARA Title III Rules (40 CFR Part 370)
Immediate (Acute) Health Y Fire Y
Delayed (Chronic) Health N Reactive N
Sudden Release of Pressure N
The components of this product are all on the TSCA Inventory list.
Ingredient Related Regulatory Information:
CERCLA RQ SARA TPQ
SARA Reportable Quantities
Trans-1,2-dichloroethylene 1000 LBS NE
SARA Title III, Section 313
This product does contain chemical(s) which are defined as toxic chemicals under and subject to the reporting requirements of, Section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372. See Section 2
Trans-1,2-dichloroethylene
Massachusetts Right to Know
This product does contain the following chemicals(s), as indicated below, currently on the Massachusetts Right to Know Substance
List.
Trans-1,2-dichloroethylene
Product Code: 04801 Page 5
Revision: 7 Issued: 08 NOV 2004 of 6
Transcend (TM) Additive
Material Safety Data Sheet
Arkema Inc.
New Jersey Right to Know
This product does contain the following chemical(s), as indicated below, currently on the New Jersey Right-to-Know Substances List.
Trans-1,2-dichloroethylene
Pennsylvania Environmental Hazard
This product does contain the following chemical(s), as indicated below, currently on the Pennsylvania Environmental Hazard List.
Trans-1,2-dichloroethylene
Pennsylvania Right to Know
This product does contain the following chemical(s), as indicated below, currently on the Pennsylvania Hazardous Substance List.
Trans-1,2-dichloroethylene
16 OTHER INFORMATION
Revision Information
Revision Number 7
08 NOV 2004
Revision Date
Supercedes Revision Dated 05-NOV-2004
Revision Summary
Revised section 12.
Key
NE= Not Established NA= Not Applicable (R) = Registered Trademark
Arkema Inc. believes that the information and recommendations contained herein (including data and
statements) are accurate as of the date hereof. NO WARRANTY OF FITNESS FOR ANY PARTICULAR
PURPOSE, WARRANTY OF MERCHANTABILITY, OR ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, IS MADE CONCERNING THE INFORMATION PROVIDED HEREIN. The information provided
herein relates only to the specific product designated and may not be valid where such product is used in
combination with any other materials or in any process. Further, since the conditions and methods of use are
beyond the control of Arkema Inc., Arkema Inc. expressly disclaims any and all liability as to any results
obtained or arising from any use of the product or reliance on such information.
Product Code: 04801 Page 6
Revision: 7 Issued: 08 NOV 2004 of 6
|